// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)

/dts-v1/;

#include "ipq5018.dtsi"
#include "ipq5018-avm-common.dtsi"
#include <dt-bindings/pwm/pwm.h>

/ {
	model = "AVM FRITZ!Box 7530 AX TypB";

	#address-cells = <0x2>;
	#size-cells = <0x2>;

	interrupt-parent = <&intc>;

	/delete-property/ MP_256;
	MP_512;

	dect_gpio: dect-gpio {
		compatible = "avm,gpio-aggregator";
		gpios = <&tlmm 44 GPIO_ACTIVE_HIGH>,
				<&tlmm 12 GPIO_ACTIVE_HIGH>;
		gpio-line-names = "DECT_RST", "DECT_RD";
	};
	/* measure clock and fs from tdm-interface (piglet, pcmlink) */
	tdmclkfs_gpio: tdmclkfs-gpio {
		compatible = "avm,gpio-aggregator";
		gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>,
			<&tlmm 24 GPIO_ACTIVE_HIGH>;
		gpio-line-names = "TDM_FS", "TDM_CLK";
	};

	avm_netdev_map {
		compatible = "avm,port_netdev";

		lan1 {
			netdev = "eth0";
		};
		lan2 {
			netdev = "eth1";
		};
		lan3 {
			netdev = "eth2";
		};
		lan4 {
			netdev = "eth3";
		};
	};

	avm-rt-framework {
		compatible = "avm,rt_framework";

		ipi-gic-sgi = <9>, <10>, <11>, <12>, <13>, <14>;
	};

	aliases {
		sdhc1 = &sdhc_1; /* SDC1 eMMC slot */
		serial0 = &blsp1_uart1;
		serial1 = &blsp1_uart2;
		ethernet0 = "/soc/dp1";
		ethernet1 = "/soc/dp2";
	};

	chosen {
		bootargs-append = " swiotlb=1";
		stdout-path = "serial0";
	};

	reserved-memory {
		/delete-node/ nss@40000000;

		nss@40000000 {
			no-map;
			reg = <0x0 0x40000000 0x0 0x0800000>;
		};

		q6_mem_regions: q6_mem_regions@4b000000 {
			no-map;
			reg = <0x0 0x4b000000 0x0 0x3900000>;
		};

		q6_code_data: q6_code_data@4b000000 {
			no-map;
			reg = <0x0 0x4b000000 0x0 0x1000000>;
		};

		q6_ipq5018_data: q6_ipq5018_data@4c000000 {
			no-map;
			reg = <0x0 0x4c000000 0x0 0xE00000>;
		};

		m3_dump: m3_dump@4CE00000 {
			no-map;
			reg = <0x0 0x4CE00000 0x0 0x100000>;
		};

		q6_etr_region:q6_etr_dump@4CF00000 {
			no-map;
			reg = <0x0 0x4CF00000 0x0 0x100000>;
		};

		q6_caldb_region: q6_caldb_region@4d000000 {
			no-map;
			reg = <0x0 0x4d000000 0x0 0x200000>;
		};

		q6_qcn6122_data1: q6_qcn6122_data1@4d200000 {
			no-map;
			reg = <0x0 0x4d200000 0x0 0x1000000>;
		};

		m3_dump_qcn6122_1: m3_dump_qcn6122_1@4e200000 {
			no-map;
			reg = <0x0 0x4e200000 0x0 0x100000>;
		};

		q6_qcn6122_etr_1: q6_qcn6122_etr_1@4e300000 {
			no-map;
			reg = <0x0 0x4e300000 0x0 0x100000>;
		};

		q6_qcn6122_caldb_1: q6_qcn6122_caldb_1@4e400000 {
			no-map;
			reg = <0x0 0x4e400000 0x0 0x500000>;
		};
	};

	soc {
		serial@78af000 {
			status = "ok";
			pinctrl-0 = <&blsp0_uart_pins>;
			pinctrl-names = "default";
		};

		serial@78b0000 {
			status = "ok";
			pinctrl-0 = <&blsp1_uart_pins>;
			pinctrl-names = "default";
		};

		qpic_bam: dma@7984000{
			status = "ok";
		};

		nand: qpic-nand@79b0000 {
			pinctrl-0 = <&qspi_nand_pins>;
			pinctrl-names = "default";
			status = "ok";
		};

		mdio0: mdio@88000 {
			#address-cells = <1>;
			#size-cells = <0>;
			status = "ok";

			ethernet-phy@0 {
				reg = <7>;
			};
		};

		mdio1: mdio@90000 {
			status = "ok";
			pinctrl-0 = <&mdio1_pins>;
			pinctrl-names = "default";
			phy-reset-gpio = <&tlmm 1 GPIO_ACTIVE_HIGH>;

			/*
			 * reduce mdio clock rate as early designs do not
			 * support higher rates. Starting with HWSubrev 4
			 * we can remove this rate reducton. We also have to do
			 * so as we see telephony issues with a reduced mdio
			 * clock rate.
			 */
			avm,clk_div = <0x3>;

			ethernet-phy@0 {
				reg = <0>;
			};

			ethernet-phy@1 {
				reg = <1>;
			};

			ethernet-phy@2 {
				reg = <2>;
			};

			ethernet-phy@3 {
				reg = <3>;
			};

			ethernet-phy@4 {
				reg = <4>;
			};
		};

		ess-instance {
			num_devices = <0x2>;
			#address-cells = <1>;
			#size-cells = <0>;
			ess-switch@0x39c00000 {
				device_id = <0>;
				switch_mac_mode = <0xf>; /* SGMII */
				cmnblk_clk = "internal_96MHz"; /* cmnblk clk*/
				qcom,port_phyinfo {
					port@0 {
						port_id = <1>;
						phy_address = <7>;
						mdiobus = <&mdio0>;
					};
					/* Required to get GMAC2 up and running */
					port@1 {
						port_id = <2>;
						forced-speed = <1000>;
						forced-duplex = <1>;
					};
				};
			};
			ess-switch1@1 {
				compatible = "qcom,ess-switch-qca83xx";
				device_id = <1>;
				switch_access_mode = "mdio";
				mdio-bus = <&mdio1>;
				switch_cpu_bmp = <0x40>;  /* cpu port bitmap */
				switch_lan_bmp = <0x2A>; /* lan port bitmap */
				switch_wan_bmp = <0x0>;  /* wan port bitmap */
				qca,ar8327-initvals = <
						0x00004 0x7600000   /* PAD0_MODE */
						0x00008 0x1000000   /* PAD5_MODE */
						0x0000c 0x80        /* PAD6_MODE */
						0x00010 0x2613a0    /* PORT6 FORCE MODE*/
						0x000e4 0xaa545     /* MAC_POWER_SEL */
						0x000e0 0xc74164de  /* SGMII_CTRL */
						0x0007c 0x4e        /* PORT0_STATUS */
						0x00094 0x4e        /* PORT6_STATUS */
				>;
				qcom,port_phyinfo {
					port@0 {
						port_id = <1>;
						phy_address = <0>;
						mdiobus = <&mdio1>;
					};
					port@1 {
						port_id = <2>;
						phy_address = <1>;
						mdiobus = <&mdio1>;
					};
					port@2 {
						port_id = <3>;
						phy_address = <2>;
						mdiobus = <&mdio1>;
					};
					port@3 {
						port_id = <4>;
						phy_address = <3>;
						mdiobus = <&mdio1>;
					};
					port@4 {
						port_id = <5>;
						phy_address = <4>;
						mdiobus = <&mdio1>;
					};
				};
			};
		};

		q6v5_wcss@CD00000 {
			memory-region = <&q6_mem_regions>;
		};

		nss-common {
			avm,mem-profile-medium;
		};

		dp1: dp1 {
			device_type = "network";
			compatible = "qcom,nss-dp";
			clocks = <&gcc GCC_SNOC_GMAC0_AXI_CLK>;
			clock-names = "nss-snoc-gmac-axi-clk";
			qcom,id = <1>;
			reg = <0x39C00000 0x10000>;
			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
			qcom,mactype = <2>;
			qcom,link-poll = <1>;
			qcom,phy-mdio-addr = <7>;
			mdio-bus = <&mdio0>;
			local-mac-address = [000000000000];
			phy-mode = "sgmii";
			devname = "eth3";
			macname = "usb_board_mac";
		};

		dp2 {
			status = "ok";
			device_type = "network";
			compatible = "qcom,nss-dp";
			clocks = <&gcc GCC_SNOC_GMAC1_AXI_CLK>;
			clock-names = "nss-snoc-gmac-axi-clk";
			qcom,id = <2>;
			reg = <0x39D00000 0x10000>;
			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
			qcom,mactype = <2>;
			local-mac-address = [000000000000];
			phy-mode = "sgmii";
			devname = "gmac1";
			avm,no_pa;
			avm,portid;
		};

		virt_dp1: virt-dp1 {
			compatible = "avm,nss-virtifmgr";
			status = "ok";
			phy-mode = "sgmii";
			devname = "eth0";
			macname = "maca";
			identifier = <1>;
			gmac_id = <1>;
			port_id = <1>;
			type = <2>;
			mdio-bus = <&mdio1>;
			phy_addr = <0>;
		};

		virt_dp2: virt-dp2 {
			compatible = "avm,nss-virtifmgr";
			status = "ok";
			phy-mode = "sgmii";
			devname = "eth1";
			macname = "macb";
			identifier = <2>;
			gmac_id = <1>;
			port_id = <3>;
			type = <2>;
			mdio-bus = <&mdio1>;
			phy_addr = <2>;
		};

		virt_dp3: virt-dp3 {
			compatible = "avm,nss-virtifmgr";
			status = "ok";
			phy-mode = "sgmii";
			devname = "eth2";
			macname = "usb_rndis_mac";
			identifier = <3>;
			gmac_id = <1>;
			port_id = <5>;
			type = <2>;
			mdio-bus = <&mdio1>;
			phy_addr = <4>;
		};

		qcom,test@0 {
			status = "ok";
		};

		lpass: lpass@0xA000000 {
			status = "ok";
		};

		audio_mclk {
			status = "ok";
		};

		pcm_avm: pcm_avm@0xA3C0000 {
			status = "ok";
		};

		pcm_lb: pcm_lb@0 {
			status = "ok";
		};
	};

	avm-usb-en-gpio {
		compatible = "avm,gpio-aggregator";
		pinctrl-0 = <&usb_pw_en_pins>;
		pinctrl-names = "default";

		gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
		gpio-line-names = "usb-pwr-en";
	};
};

&sdhc_1 {
	status = "disabled";
};

&tlmm {
	blsp0_uart_pins: blsp0_uart_pins {
		blsp0_uart_rx {
			pins = "gpio21";
			function = "blsp0_uart0";
			drive-strength = <8>;
		};
		blsp0_uart_tx {
			pins = "gpio20";
			function = "blsp0_uart0";
			drive-strength = <8>;
		};
	};

	blsp1_uart_pins: blsp1_uart_pins {
		blsp1_uart_rx {
			pins = "gpio12";
			function = "blsp1_uart0";
			drive-strength = <8>;
		};
		blsp1_uart_tx {
			pins = "gpio11";
			function = "blsp1_uart0";
			drive-strength = <8>;
		};
	};

	qspi_nand_pins: qspi_nand_pins {
		qspi_clock {
			pins = "gpio9";
			function = "qspi_clk";
			drive-strength = <8>;
			bias-disable;
		};

		qspi_cs {
			pins = "gpio8";
			function = "qspi_cs";
			drive-strength = <8>;
			bias-disable;
		};

		qspi_data {
			pins = "gpio4", "gpio5", "gpio6", "gpio7";
			function = "qspi_data";
			drive-strength = <8>;
			bias-disable;
		};
	};

	mdio1_pins: mdio_pinmux {
		mux_0 {
			pins = "gpio36";
			function = "mdc";
			drive-strength = <8>;
			bias-pull-up;
		};

		mux_1 {
			pins = "gpio37";
			function = "mdio";
			drive-strength = <8>;
			bias-pull-up;
		};
	};

	usb_pw_en_pins: usb_pwr_en_pinmux {
		pins = "gpio45";
		function = "gpio";
		drive-strength = <8>;
		bias-disable;
	};
};

&pcie_x1phy {
	status = "disabled";
};

&pcie_x1 {
	status = "disabled";
};

&pcie_x2phy {
	status = "ok";
};

&pcie_x2 {
	status = "ok";
	perst-gpio = <&tlmm 3 GPIO_ACTIVE_LOW>;
	avm,host_magic;
};

&eud {
	status = "ok";
};

&dwc_0 {
	/delete-property/ #phy-cells;
	/delete-property/ phys;
	/delete-property/ phy-names;
};

&hs_m31phy_0 {
	status = "ok";
};

&usb3 {
	status = "ok";
};

&pcie_x1_rp {
	#address-cells = <5>;
	#size-cells = <0>;
	mhi_0: qcom,mhi@0 {
		reg = <0 0 0 0 0 >;
	};
};

&qfprom {
	status = "ok";
};

&tsens {
	status = "ok";
};

/*
&qgic_msi_0 {
	status = "ok";
};

&qgic_msi_1 {
	status = "ok";
};
*/

&q6v5_wcss {
	qcom,nosecure;
	qcom,multipd_arch;
	memory-region = <&q6_mem_regions>;
	qcom,share_bootargs;
	qcom,bootargs_smem = <507>;
	boot-args = <0x2 0x4 0x2 0xf 0x0 0x0>;
	/* IPQ5018 */
	q6v5_wcss_userpd1 {
		m3_firmware = "IPQ5018/m3_fw.mdt";
		interrupts-extended = <&wcss_smp2p_in 8 0>,
			<&wcss_smp2p_in 9 0>,
			<&wcss_smp2p_in 12 0>,
			<&wcss_smp2p_in 11 0>;
		interrupt-names ="fatal",
			"ready",
			"spawn_ack",
			"stop-ack";
		qcom,smem-states = <&wcss_smp2p_out 8>,
			<&wcss_smp2p_out 9>,
			<&wcss_smp2p_out 10>;
		qcom,smem-state-names = "shutdown",
			"stop",
			"spawn";
		qca,asid = <1>;
		qca,auto-restart;
		qca,int_radio;
		memory-region = <&q6_ipq5018_data>, <&m3_dump>,
				<&q6_etr_region>, <&q6_caldb_region>;
	};

	/* QCN6122 5G */
	q6v5_wcss_userpd2 {
		m3_firmware = "qcn6122/m3_fw.mdt";
		interrupts-extended = <&wcss_smp2p_in 16 0>,
			<&wcss_smp2p_in 17 0>,
			<&wcss_smp2p_in 20 0>,
			<&wcss_smp2p_in 19 0>;
		interrupt-names ="fatal",
			"ready",
			"spawn_ack",
			"stop-ack";
		qcom,smem-states = <&wcss_smp2p_out 16>,
			<&wcss_smp2p_out 17>,
			<&wcss_smp2p_out 18>;
		qcom,smem-state-names = "shutdown",
			"stop",
			"spawn";
		qca,asid = <2>;
		qca,auto-restart;
		memory-region = <&q6_qcn6122_data1>, <&m3_dump_qcn6122_1>,
				<&q6_qcn6122_etr_1>, <&q6_qcn6122_caldb_1>;
	};
};

&wifi0 {
	/* IPQ5018 */
	qcom,multipd_arch;
	qcom,tgt-mem-mode = <1>;
	qcom,board_id = <0x23>;
	qcom,bdf-addr = <0x0 0x4c000000 0x4c000000 0x0 0x0>;
	qcom,caldb-addr = <0x0 0x4D000000 0 0 0>;
	qcom,caldb-size = <0x200000>;
	qcom,userpd-subsys-name = "q6v5_wcss_userpd1";
	status = "ok";
};

&wlan_cma_5G_0 {
	status = "ok";
};

&wifi1 {
	/* QCN6122 5G */
	qcom,multipd_arch;
	qcom,tgt-mem-mode = <1>;
	qcom,board_id = <0x60>;
	/*
	 * once wifi driver changes are in place to
	 * qcn6122 compatible string, remove qcn9100 here
	 */
	compatible = "qcom,cnss-qcn9100", "qcom,cnss-qcn6122";
	memory-region = <&wlan_cma_5G_0>;
	qcom,bdf-addr = <0x0 0x4d200000 0x4cf00000 0x0 0x0>;
	qcom,caldb-addr = <0x0 0x4E400000 0 0 0>;
	qcom,caldb-size = <0x500000>;
	qcom,userpd-subsys-name = "q6v5_wcss_userpd2";
	status = "ok";
};