--- zzzz-none-000/linux-5.4.213/drivers/hwtracing/coresight/Kconfig	2022-09-15 10:04:56.000000000 +0000
+++ alder-5690pro-762/linux-5.4.213/drivers/hwtracing/coresight/Kconfig	2024-08-14 09:01:58.000000000 +0000
@@ -26,6 +26,7 @@
 config CORESIGHT_LINK_AND_SINK_TMC
 	bool "Coresight generic TMC driver"
 	depends on CORESIGHT_LINKS_AND_SINKS
+	select CORESIGHT_CSR
 	help
 	  This enables support for the Trace Memory Controller driver.
 	  Depending on its configuration the device can act as a link (embedded
@@ -75,7 +76,6 @@
 
 config CORESIGHT_SOURCE_ETM4X
 	bool "CoreSight Embedded Trace Macrocell 4.x driver"
-	depends on ARM64
 	select CORESIGHT_LINKS_AND_SINKS
 	select PID_IN_CONTEXTIDR
 	help
@@ -109,4 +109,99 @@
 	  properly, please refer Documentation/trace/coresight-cpu-debug.rst
 	  for detailed description and the example for usage.
 
+config CORESIGHT_CTI
+	bool "CoreSight Cross Trigger Interface driver"
+	help
+	  This driver provides support for Cross Trigger Interface that is
+	  used to input or output i.e. pass cross trigger events from one
+	  hardware component to another. It can also be used to pass
+	  software generated events.
+
+config CORESIGHT_CTI_SAVE_DISABLE
+	bool "Turn off CTI save and restore"
+	depends on CORESIGHT_CTI
+	help
+	  Turns off CoreSight CTI save and restore support for cpu CTIs. This
+	  avoids voting for the clocks during probe as well as the associated
+	  save and restore latency at the cost of breaking cpu CTI support on
+	  targets where cpu CTIs have to be preserved across power collapse.
+
+	  If unsure, say 'N' here to avoid breaking cpu CTI support.
+
+config CORESIGHT_TPDA
+	bool "CoreSight Trace, Profiling & Diagnostics Aggregator driver"
+	help
+	  This driver provides support for configuring aggregator. This is
+	  primarily useful for pulling the data sets from one or more
+	  attached monitors and pushing the resultant data out. Multiple
+	  monitors are connected on different input ports of TPDA.
+
+config CORESIGHT_TPDM
+	bool "CoreSight Trace, Profiling & Diagnostics Monitor driver"
+	help
+	  This driver provides support for configuring monitor. Monitors are
+	  primarily responsible for data set collection and support the
+	  ability to collect any permutation of data set types. Monitors are
+	  also responsible for interaction with system cross triggering.
+
+config CORESIGHT_TPDM_DEFAULT_ENABLE
+	bool "Turn on TPDM tracing by default"
+	depends on CORESIGHT_TPDM
+	help
+	  Turns on CoreSight TPDM tracing for different data set types by
+	  default. Otherwise, tracing is disabled by default but can be
+	  enabled via sysfs.
+
+	  If unsure, say 'N' here to avoid potential power and performance
+	  penalty.
+
+config CORESIGHT_CSR
+	bool "CoreSight Slave Register driver"
+	help
+	  This driver provides support for CoreSight Slave Register block
+	  that hosts miscellaneous configuration registers.
+	  Those configuration registers can be used to control, various
+	  coresight configurations.
+
+config CORESIGHT_HWEVENT
+	bool "CoreSight Hardware Event driver"
+	depends on CORESIGHT_STM
+	select CORESIGHT_CSR
+	help
+	  This driver provides support for monitoring and tracing CoreSight
+	  Hardware Event across STM interface. It configures Coresight
+	  Hardware Event mux control registers to select hardware events
+	  based on user input.
+
+config CORESIGHT_DUMMY
+	bool "Dummy driver support"
+	help
+	  Enables support for dummy driver. Dummy driver can be used for
+	  CoreSight sources/sinks that are owned and configured by some
+	  other subsystem and use Linux drivers to configure rest of trace
+	  path.
+
+config CORESIGHT_REMOTE_ETM
+	bool "Remote processor ETM trace support"
+	depends on QCOM_QMI_HELPERS=y
+	help
+	  Enables support for ETM trace collection on remote processor using
+	  CoreSight framework. Enabling this will allow turning on ETM
+	  tracing on remote processor via sysfs by configuring the required
+	  CoreSight components.
+
+config CORESIGHT_REMOTE_ETM_DEFAULT_ENABLE
+	int "default enable ETM for Remote processor based on instance id"
+	depends on CORESIGHT_REMOTE_ETM
+	default 0
+	help
+	  Support for enabling separated Remote processor ETM tracing. Depends
+	  on if instance id bit is set.
+
+config CORESIGHT_STREAM
+	tristate "Coresight network stream driver"
+	depends on CORESIGHT_LINK_AND_SINK_TMC && NET && NET_UDP_TUNNEL
+	help
+	  This enables support for the Coresight network stream driver.
+
 endif