/* * drivers/mtd/nand/pxa3xx_nand.c * * Copyright © 2005 Intel Corporation * Copyright © 2006 Marvell International Ltd. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. * * See Documentation/mtd/nand/pxa3xx-nand.txt for more details. */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #if defined(CONFIG_ARCH_PXA) || defined(CONFIG_ARCH_MMP) #define ARCH_HAS_DMA #endif #ifdef ARCH_HAS_DMA #include #endif #include #define CHIP_DELAY_TIMEOUT msecs_to_jiffies(200) #define NAND_STOP_DELAY msecs_to_jiffies(40) #define PAGE_CHUNK_SIZE (2048) /* * Define a buffer size for the initial command that detects the flash device: * STATUS, READID and PARAM. The largest of these is the PARAM command, * needing 256 bytes. */ #define INIT_BUFFER_SIZE 256 /* registers and bit definitions */ #define NDCR (0x00) /* Control register */ #define NDTR0CS0 (0x04) /* Timing Parameter 0 for CS0 */ #define NDTR1CS0 (0x0C) /* Timing Parameter 1 for CS0 */ #define NDSR (0x14) /* Status Register */ #define NDPCR (0x18) /* Page Count Register */ #define NDBDR0 (0x1C) /* Bad Block Register 0 */ #define NDBDR1 (0x20) /* Bad Block Register 1 */ #define NDECCCTRL (0x28) /* ECC control */ #define NDDB (0x40) /* Data Buffer */ #define NDCB0 (0x48) /* Command Buffer0 */ #define NDCB1 (0x4C) /* Command Buffer1 */ #define NDCB2 (0x50) /* Command Buffer2 */ #define NDCR_SPARE_EN (0x1 << 31) #define NDCR_ECC_EN (0x1 << 30) #define NDCR_DMA_EN (0x1 << 29) #define NDCR_ND_RUN (0x1 << 28) #define NDCR_DWIDTH_C (0x1 << 27) #define NDCR_DWIDTH_M (0x1 << 26) #define NDCR_PAGE_SZ (0x1 << 24) #define NDCR_NCSX (0x1 << 23) #define NDCR_ND_MODE (0x3 << 21) #define NDCR_NAND_MODE (0x0) #define NDCR_CLR_PG_CNT (0x1 << 20) #define NDCR_STOP_ON_UNCOR (0x1 << 19) #define NDCR_RD_ID_CNT_MASK (0x7 << 16) #define NDCR_RD_ID_CNT(x) (((x) << 16) & NDCR_RD_ID_CNT_MASK) #define NDCR_RA_START (0x1 << 15) #define NDCR_PG_PER_BLK (0x1 << 14) #define NDCR_ND_ARB_EN (0x1 << 12) #define NDCR_INT_MASK (0xFFF) #define NDSR_MASK (0xfff) #define NDSR_ERR_CNT_OFF (16) #define NDSR_ERR_CNT_MASK (0x1f) #define NDSR_ERR_CNT(sr) ((sr >> NDSR_ERR_CNT_OFF) & NDSR_ERR_CNT_MASK) #define NDSR_RDY (0x1 << 12) #define NDSR_FLASH_RDY (0x1 << 11) #define NDSR_CS0_PAGED (0x1 << 10) #define NDSR_CS1_PAGED (0x1 << 9) #define NDSR_CS0_CMDD (0x1 << 8) #define NDSR_CS1_CMDD (0x1 << 7) #define NDSR_CS0_BBD (0x1 << 6) #define NDSR_CS1_BBD (0x1 << 5) #define NDSR_UNCORERR (0x1 << 4) #define NDSR_CORERR (0x1 << 3) #define NDSR_WRDREQ (0x1 << 2) #define NDSR_RDDREQ (0x1 << 1) #define NDSR_WRCMDREQ (0x1) #define NDCB0_LEN_OVRD (0x1 << 28) #define NDCB0_ST_ROW_EN (0x1 << 26) #define NDCB0_AUTO_RS (0x1 << 25) #define NDCB0_CSEL (0x1 << 24) #define NDCB0_EXT_CMD_TYPE_MASK (0x7 << 29) #define NDCB0_EXT_CMD_TYPE(x) (((x) << 29) & NDCB0_EXT_CMD_TYPE_MASK) #define NDCB0_CMD_TYPE_MASK (0x7 << 21) #define NDCB0_CMD_TYPE(x) (((x) << 21) & NDCB0_CMD_TYPE_MASK) #define NDCB0_NC (0x1 << 20) #define NDCB0_DBC (0x1 << 19) #define NDCB0_ADDR_CYC_MASK (0x7 << 16) #define NDCB0_ADDR_CYC(x) (((x) << 16) & NDCB0_ADDR_CYC_MASK) #define NDCB0_CMD2_MASK (0xff << 8) #define NDCB0_CMD1_MASK (0xff) #define NDCB0_ADDR_CYC_SHIFT (16) #define EXT_CMD_TYPE_DISPATCH 6 /* Command dispatch */ #define EXT_CMD_TYPE_NAKED_RW 5 /* Naked read or Naked write */ #define EXT_CMD_TYPE_READ 4 /* Read */ #define EXT_CMD_TYPE_DISP_WR 4 /* Command dispatch with write */ #define EXT_CMD_TYPE_FINAL 3 /* Final command */ #define EXT_CMD_TYPE_LAST_RW 1 /* Last naked read/write */ #define EXT_CMD_TYPE_MONO 0 /* Monolithic read/write */ /* macros for registers read/write */ #define nand_writel(info, off, val) \ writel_relaxed((val), (info)->mmio_base + (off)) #define nand_readl(info, off) \ readl_relaxed((info)->mmio_base + (off)) /* error code and state */ enum { ERR_NONE = 0, ERR_DMABUSERR = -1, ERR_SENDCMD = -2, ERR_UNCORERR = -3, ERR_BBERR = -4, ERR_CORERR = -5, }; enum { STATE_IDLE = 0, STATE_PREPARED, STATE_CMD_HANDLE, STATE_DMA_READING, STATE_DMA_WRITING, STATE_DMA_DONE, STATE_PIO_READING, STATE_PIO_WRITING, STATE_CMD_DONE, STATE_READY, }; enum pxa3xx_nand_variant { PXA3XX_NAND_VARIANT_PXA, PXA3XX_NAND_VARIANT_ARMADA370, }; struct pxa3xx_nand_host { struct nand_chip chip; struct mtd_info *mtd; void *info_data; /* page size of attached chip */ int use_ecc; int cs; /* calculated from pxa3xx_nand_flash data */ unsigned int col_addr_cycles; unsigned int row_addr_cycles; size_t read_id_bytes; }; struct pxa3xx_nand_info { struct nand_hw_control controller; struct platform_device *pdev; struct clk *clk; void __iomem *mmio_base; unsigned long mmio_phys; struct completion cmd_complete, dev_ready; unsigned int buf_start; unsigned int buf_count; unsigned int buf_size; unsigned int data_buff_pos; unsigned int oob_buff_pos; /* DMA information */ int drcmr_dat; int drcmr_cmd; unsigned char *data_buff; unsigned char *oob_buff; dma_addr_t data_buff_phys; int data_dma_ch; struct pxa_dma_desc *data_desc; dma_addr_t data_desc_addr; struct pxa3xx_nand_host *host[NUM_CHIP_SELECT]; unsigned int state; /* * This driver supports NFCv1 (as found in PXA SoC) * and NFCv2 (as found in Armada 370/XP SoC). */ enum pxa3xx_nand_variant variant; int cs; int use_ecc; /* use HW ECC ? */ int ecc_bch; /* using BCH ECC? */ int use_dma; /* use DMA ? */ int use_spare; /* use spare ? */ int need_wait; unsigned int data_size; /* data to be read from FIFO */ unsigned int chunk_size; /* split commands chunk size */ unsigned int oob_size; unsigned int spare_size; unsigned int ecc_size; unsigned int ecc_err_cnt; unsigned int max_bitflips; int retcode; /* cached register value */ uint32_t reg_ndcr; uint32_t ndtr0cs0; uint32_t ndtr1cs0; /* generated NDCBx register values */ uint32_t ndcb0; uint32_t ndcb1; uint32_t ndcb2; uint32_t ndcb3; }; static bool use_dma = 1; module_param(use_dma, bool, 0444); MODULE_PARM_DESC(use_dma, "enable DMA for data transferring to/from NAND HW"); static struct pxa3xx_nand_timing timing[] = { { 40, 80, 60, 100, 80, 100, 90000, 400, 40, }, { 10, 0, 20, 40, 30, 40, 11123, 110, 10, }, { 10, 25, 15, 25, 15, 30, 25000, 60, 10, }, { 10, 35, 15, 25, 15, 25, 25000, 60, 10, }, }; static struct pxa3xx_nand_flash builtin_flash_types[] = { { "DEFAULT FLASH", 0, 0, 2048, 8, 8, 0, &timing[0] }, { "64MiB 16-bit", 0x46ec, 32, 512, 16, 16, 4096, &timing[1] }, { "256MiB 8-bit", 0xdaec, 64, 2048, 8, 8, 2048, &timing[1] }, { "4GiB 8-bit", 0xd7ec, 128, 4096, 8, 8, 8192, &timing[1] }, { "128MiB 8-bit", 0xa12c, 64, 2048, 8, 8, 1024, &timing[2] }, { "128MiB 16-bit", 0xb12c, 64, 2048, 16, 16, 1024, &timing[2] }, { "512MiB 8-bit", 0xdc2c, 64, 2048, 8, 8, 4096, &timing[2] }, { "512MiB 16-bit", 0xcc2c, 64, 2048, 16, 16, 4096, &timing[2] }, { "256MiB 16-bit", 0xba20, 64, 2048, 16, 16, 2048, &timing[3] }, }; static u8 bbt_pattern[] = {'M', 'V', 'B', 'b', 't', '0' }; static u8 bbt_mirror_pattern[] = {'1', 't', 'b', 'B', 'V', 'M' }; static struct nand_bbt_descr bbt_main_descr = { .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE | NAND_BBT_2BIT | NAND_BBT_VERSION, .offs = 8, .len = 6, .veroffs = 14, .maxblocks = 8, /* Last 8 blocks in each chip */ .pattern = bbt_pattern }; static struct nand_bbt_descr bbt_mirror_descr = { .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE | NAND_BBT_2BIT | NAND_BBT_VERSION, .offs = 8, .len = 6, .veroffs = 14, .maxblocks = 8, /* Last 8 blocks in each chip */ .pattern = bbt_mirror_pattern }; static struct nand_ecclayout ecc_layout_2KB_bch4bit = { .eccbytes = 32, .eccpos = { 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63}, .oobfree = { {2, 30} } }; static struct nand_ecclayout ecc_layout_4KB_bch4bit = { .eccbytes = 64, .eccpos = { 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63, 96, 97, 98, 99, 100, 101, 102, 103, 104, 105, 106, 107, 108, 109, 110, 111, 112, 113, 114, 115, 116, 117, 118, 119, 120, 121, 122, 123, 124, 125, 126, 127}, /* Bootrom looks in bytes 0 & 5 for bad blocks */ .oobfree = { {6, 26}, { 64, 32} } }; static struct nand_ecclayout ecc_layout_4KB_bch8bit = { .eccbytes = 128, .eccpos = { 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63}, .oobfree = { } }; /* Define a default flash type setting serve as flash detecting only */ #define DEFAULT_FLASH_TYPE (&builtin_flash_types[0]) #define NDTR0_tCH(c) (min((c), 7) << 19) #define NDTR0_tCS(c) (min((c), 7) << 16) #define NDTR0_tWH(c) (min((c), 7) << 11) #define NDTR0_tWP(c) (min((c), 7) << 8) #define NDTR0_tRH(c) (min((c), 7) << 3) #define NDTR0_tRP(c) (min((c), 7) << 0) #define NDTR1_tR(c) (min((c), 65535) << 16) #define NDTR1_tWHR(c) (min((c), 15) << 4) #define NDTR1_tAR(c) (min((c), 15) << 0) /* convert nano-seconds to nand flash controller clock cycles */ #define ns2cycle(ns, clk) (int)((ns) * (clk / 1000000) / 1000) static const struct of_device_id pxa3xx_nand_dt_ids[] = { { .compatible = "marvell,pxa3xx-nand", .data = (void *)PXA3XX_NAND_VARIANT_PXA, }, { .compatible = "marvell,armada370-nand", .data = (void *)PXA3XX_NAND_VARIANT_ARMADA370, }, {} }; MODULE_DEVICE_TABLE(of, pxa3xx_nand_dt_ids); static enum pxa3xx_nand_variant pxa3xx_nand_get_variant(struct platform_device *pdev) { const struct of_device_id *of_id = of_match_device(pxa3xx_nand_dt_ids, &pdev->dev); if (!of_id) return PXA3XX_NAND_VARIANT_PXA; return (enum pxa3xx_nand_variant)of_id->data; } static void pxa3xx_nand_set_timing(struct pxa3xx_nand_host *host, const struct pxa3xx_nand_timing *t) { struct pxa3xx_nand_info *info = host->info_data; unsigned long nand_clk = clk_get_rate(info->clk); uint32_t ndtr0, ndtr1; ndtr0 = NDTR0_tCH(ns2cycle(t->tCH, nand_clk)) | NDTR0_tCS(ns2cycle(t->tCS, nand_clk)) | NDTR0_tWH(ns2cycle(t->tWH, nand_clk)) | NDTR0_tWP(ns2cycle(t->tWP, nand_clk)) | NDTR0_tRH(ns2cycle(t->tRH, nand_clk)) | NDTR0_tRP(ns2cycle(t->tRP, nand_clk)); ndtr1 = NDTR1_tR(ns2cycle(t->tR, nand_clk)) | NDTR1_tWHR(ns2cycle(t->tWHR, nand_clk)) | NDTR1_tAR(ns2cycle(t->tAR, nand_clk)); info->ndtr0cs0 = ndtr0; info->ndtr1cs0 = ndtr1; nand_writel(info, NDTR0CS0, ndtr0); nand_writel(info, NDTR1CS0, ndtr1); } /* * Set the data and OOB size, depending on the selected * spare and ECC configuration. * Only applicable to READ0, READOOB and PAGEPROG commands. */ static void pxa3xx_set_datasize(struct pxa3xx_nand_info *info, struct mtd_info *mtd) { int oob_enable = info->reg_ndcr & NDCR_SPARE_EN; info->data_size = mtd->writesize; if (!oob_enable) return; info->oob_size = info->spare_size; if (!info->use_ecc) info->oob_size += info->ecc_size; } /** * NOTE: it is a must to set ND_RUN firstly, then write * command buffer, otherwise, it does not work. * We enable all the interrupt at the same time, and * let pxa3xx_nand_irq to handle all logic. */ static void pxa3xx_nand_start(struct pxa3xx_nand_info *info) { uint32_t ndcr; ndcr = info->reg_ndcr; if (info->use_ecc) { ndcr |= NDCR_ECC_EN; if (info->ecc_bch) nand_writel(info, NDECCCTRL, 0x1); } else { ndcr &= ~NDCR_ECC_EN; if (info->ecc_bch) nand_writel(info, NDECCCTRL, 0x0); } if (info->use_dma) ndcr |= NDCR_DMA_EN; else ndcr &= ~NDCR_DMA_EN; if (info->use_spare) ndcr |= NDCR_SPARE_EN; else ndcr &= ~NDCR_SPARE_EN; ndcr |= NDCR_ND_RUN; /* clear status bits and run */ nand_writel(info, NDCR, 0); nand_writel(info, NDSR, NDSR_MASK); nand_writel(info, NDCR, ndcr); } static void pxa3xx_nand_stop(struct pxa3xx_nand_info *info) { uint32_t ndcr; int timeout = NAND_STOP_DELAY; /* wait RUN bit in NDCR become 0 */ ndcr = nand_readl(info, NDCR); while ((ndcr & NDCR_ND_RUN) && (timeout-- > 0)) { ndcr = nand_readl(info, NDCR); udelay(1); } if (timeout <= 0) { ndcr &= ~NDCR_ND_RUN; nand_writel(info, NDCR, ndcr); } /* clear status bits */ nand_writel(info, NDSR, NDSR_MASK); } static void __maybe_unused enable_int(struct pxa3xx_nand_info *info, uint32_t int_mask) { uint32_t ndcr; ndcr = nand_readl(info, NDCR); nand_writel(info, NDCR, ndcr & ~int_mask); } static void disable_int(struct pxa3xx_nand_info *info, uint32_t int_mask) { uint32_t ndcr; ndcr = nand_readl(info, NDCR); nand_writel(info, NDCR, ndcr | int_mask); } static void drain_fifo(struct pxa3xx_nand_info *info, void *data, int len) { if (info->ecc_bch) { int timeout; /* * According to the datasheet, when reading from NDDB * with BCH enabled, after each 32 bytes reads, we * have to make sure that the NDSR.RDDREQ bit is set. * * Drain the FIFO 8 32 bits reads at a time, and skip * the polling on the last read. */ while (len > 8) { __raw_readsl(info->mmio_base + NDDB, data, 8); for (timeout = 0; !(nand_readl(info, NDSR) & NDSR_RDDREQ); timeout++) { if (timeout >= 5) { dev_err(&info->pdev->dev, "Timeout on RDDREQ while draining the FIFO\n"); return; } mdelay(1); } data += 32; len -= 8; } } __raw_readsl(info->mmio_base + NDDB, data, len); } static void handle_data_pio(struct pxa3xx_nand_info *info) { unsigned int do_bytes = min(info->data_size, info->chunk_size); switch (info->state) { case STATE_PIO_WRITING: __raw_writesl(info->mmio_base + NDDB, info->data_buff + info->data_buff_pos, DIV_ROUND_UP(do_bytes, 4)); if (info->oob_size > 0) __raw_writesl(info->mmio_base + NDDB, info->oob_buff + info->oob_buff_pos, DIV_ROUND_UP(info->oob_size, 4)); break; case STATE_PIO_READING: drain_fifo(info, info->data_buff + info->data_buff_pos, DIV_ROUND_UP(do_bytes, 4)); if (info->oob_size > 0) drain_fifo(info, info->oob_buff + info->oob_buff_pos, DIV_ROUND_UP(info->oob_size, 4)); break; default: dev_err(&info->pdev->dev, "%s: invalid state %d\n", __func__, info->state); BUG(); } /* Update buffer pointers for multi-page read/write */ info->data_buff_pos += do_bytes; info->oob_buff_pos += info->oob_size; info->data_size -= do_bytes; } #ifdef ARCH_HAS_DMA static void start_data_dma(struct pxa3xx_nand_info *info) { struct pxa_dma_desc *desc = info->data_desc; int dma_len = ALIGN(info->data_size + info->oob_size, 32); desc->ddadr = DDADR_STOP; desc->dcmd = DCMD_ENDIRQEN | DCMD_WIDTH4 | DCMD_BURST32 | dma_len; switch (info->state) { case STATE_DMA_WRITING: desc->dsadr = info->data_buff_phys; desc->dtadr = info->mmio_phys + NDDB; desc->dcmd |= DCMD_INCSRCADDR | DCMD_FLOWTRG; break; case STATE_DMA_READING: desc->dtadr = info->data_buff_phys; desc->dsadr = info->mmio_phys + NDDB; desc->dcmd |= DCMD_INCTRGADDR | DCMD_FLOWSRC; break; default: dev_err(&info->pdev->dev, "%s: invalid state %d\n", __func__, info->state); BUG(); } DRCMR(info->drcmr_dat) = DRCMR_MAPVLD | info->data_dma_ch; DDADR(info->data_dma_ch) = info->data_desc_addr; DCSR(info->data_dma_ch) |= DCSR_RUN; } static void pxa3xx_nand_data_dma_irq(int channel, void *data) { struct pxa3xx_nand_info *info = data; uint32_t dcsr; dcsr = DCSR(channel); DCSR(channel) = dcsr; if (dcsr & DCSR_BUSERR) { info->retcode = ERR_DMABUSERR; } info->state = STATE_DMA_DONE; enable_int(info, NDCR_INT_MASK); nand_writel(info, NDSR, NDSR_WRDREQ | NDSR_RDDREQ); } #else static void start_data_dma(struct pxa3xx_nand_info *info) {} #endif static irqreturn_t pxa3xx_nand_irq_thread(int irq, void *data) { struct pxa3xx_nand_info *info = data; handle_data_pio(info); info->state = STATE_CMD_DONE; nand_writel(info, NDSR, NDSR_WRDREQ | NDSR_RDDREQ); return IRQ_HANDLED; } static irqreturn_t pxa3xx_nand_irq(int irq, void *devid) { struct pxa3xx_nand_info *info = devid; unsigned int status, is_completed = 0, is_ready = 0; unsigned int ready, cmd_done; irqreturn_t ret = IRQ_HANDLED; if (info->cs == 0) { ready = NDSR_FLASH_RDY; cmd_done = NDSR_CS0_CMDD; } else { ready = NDSR_RDY; cmd_done = NDSR_CS1_CMDD; } status = nand_readl(info, NDSR); if (status & NDSR_UNCORERR) info->retcode = ERR_UNCORERR; if (status & NDSR_CORERR) { info->retcode = ERR_CORERR; if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370 && info->ecc_bch) info->ecc_err_cnt = NDSR_ERR_CNT(status); else info->ecc_err_cnt = 1; /* * Each chunk composing a page is corrected independently, * and we need to store maximum number of corrected bitflips * to return it to the MTD layer in ecc.read_page(). */ info->max_bitflips = max_t(unsigned int, info->max_bitflips, info->ecc_err_cnt); } if (status & (NDSR_RDDREQ | NDSR_WRDREQ)) { /* whether use dma to transfer data */ if (info->use_dma) { disable_int(info, NDCR_INT_MASK); info->state = (status & NDSR_RDDREQ) ? STATE_DMA_READING : STATE_DMA_WRITING; start_data_dma(info); goto NORMAL_IRQ_EXIT; } else { info->state = (status & NDSR_RDDREQ) ? STATE_PIO_READING : STATE_PIO_WRITING; ret = IRQ_WAKE_THREAD; goto NORMAL_IRQ_EXIT; } } if (status & cmd_done) { info->state = STATE_CMD_DONE; is_completed = 1; } if (status & ready) { info->state = STATE_READY; is_ready = 1; } if (status & NDSR_WRCMDREQ) { nand_writel(info, NDSR, NDSR_WRCMDREQ); status &= ~NDSR_WRCMDREQ; info->state = STATE_CMD_HANDLE; /* * Command buffer registers NDCB{0-2} (and optionally NDCB3) * must be loaded by writing directly either 12 or 16 * bytes directly to NDCB0, four bytes at a time. * * Direct write access to NDCB1, NDCB2 and NDCB3 is ignored * but each NDCBx register can be read. */ nand_writel(info, NDCB0, info->ndcb0); nand_writel(info, NDCB0, info->ndcb1); nand_writel(info, NDCB0, info->ndcb2); /* NDCB3 register is available in NFCv2 (Armada 370/XP SoC) */ if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370) nand_writel(info, NDCB0, info->ndcb3); } /* clear NDSR to let the controller exit the IRQ */ nand_writel(info, NDSR, status); if (is_completed) complete(&info->cmd_complete); if (is_ready) complete(&info->dev_ready); NORMAL_IRQ_EXIT: return ret; } static inline int is_buf_blank(uint8_t *buf, size_t len) { for (; len > 0; len--) if (*buf++ != 0xff) return 0; return 1; } static void set_command_address(struct pxa3xx_nand_info *info, unsigned int page_size, uint16_t column, int page_addr) { /* small page addr setting */ if (page_size < PAGE_CHUNK_SIZE) { info->ndcb1 = ((page_addr & 0xFFFFFF) << 8) | (column & 0xFF); info->ndcb2 = 0; } else { info->ndcb1 = ((page_addr & 0xFFFF) << 16) | (column & 0xFFFF); if (page_addr & 0xFF0000) info->ndcb2 = (page_addr & 0xFF0000) >> 16; else info->ndcb2 = 0; } } static void prepare_start_command(struct pxa3xx_nand_info *info, int command) { struct pxa3xx_nand_host *host = info->host[info->cs]; struct mtd_info *mtd = host->mtd; /* reset data and oob column point to handle data */ info->buf_start = 0; info->buf_count = 0; info->oob_size = 0; info->data_buff_pos = 0; info->oob_buff_pos = 0; info->use_ecc = 0; info->use_spare = 1; info->retcode = ERR_NONE; info->ecc_err_cnt = 0; info->ndcb3 = 0; info->need_wait = 0; switch (command) { case NAND_CMD_READ0: case NAND_CMD_PAGEPROG: info->use_ecc = 1; case NAND_CMD_READOOB: pxa3xx_set_datasize(info, mtd); break; case NAND_CMD_PARAM: info->use_spare = 0; break; default: info->ndcb1 = 0; info->ndcb2 = 0; break; } /* * If we are about to issue a read command, or about to set * the write address, then clean the data buffer. */ if (command == NAND_CMD_READ0 || command == NAND_CMD_READOOB || command == NAND_CMD_SEQIN) { info->buf_count = mtd->writesize + mtd->oobsize; memset(info->data_buff, 0xFF, info->buf_count); } } static int prepare_set_command(struct pxa3xx_nand_info *info, int command, int ext_cmd_type, uint16_t column, int page_addr) { int addr_cycle, exec_cmd; struct pxa3xx_nand_host *host; struct mtd_info *mtd; host = info->host[info->cs]; mtd = host->mtd; addr_cycle = 0; exec_cmd = 1; if (info->cs != 0) info->ndcb0 = NDCB0_CSEL; else info->ndcb0 = 0; if (command == NAND_CMD_SEQIN) exec_cmd = 0; addr_cycle = NDCB0_ADDR_CYC(host->row_addr_cycles + host->col_addr_cycles); switch (command) { case NAND_CMD_READOOB: case NAND_CMD_READ0: info->buf_start = column; info->ndcb0 |= NDCB0_CMD_TYPE(0) | addr_cycle | NAND_CMD_READ0; if (command == NAND_CMD_READOOB) info->buf_start += mtd->writesize; /* * Multiple page read needs an 'extended command type' field, * which is either naked-read or last-read according to the * state. */ if (mtd->writesize == PAGE_CHUNK_SIZE) { info->ndcb0 |= NDCB0_DBC | (NAND_CMD_READSTART << 8); } else if (mtd->writesize > PAGE_CHUNK_SIZE) { info->ndcb0 |= NDCB0_DBC | (NAND_CMD_READSTART << 8) | NDCB0_LEN_OVRD | NDCB0_EXT_CMD_TYPE(ext_cmd_type); info->ndcb3 = info->chunk_size + info->oob_size; } set_command_address(info, mtd->writesize, column, page_addr); break; case NAND_CMD_SEQIN: info->buf_start = column; set_command_address(info, mtd->writesize, 0, page_addr); /* * Multiple page programming needs to execute the initial * SEQIN command that sets the page address. */ if (mtd->writesize > PAGE_CHUNK_SIZE) { info->ndcb0 |= NDCB0_CMD_TYPE(0x1) | NDCB0_EXT_CMD_TYPE(ext_cmd_type) | addr_cycle | command; /* No data transfer in this case */ info->data_size = 0; exec_cmd = 1; } break; case NAND_CMD_PAGEPROG: if (is_buf_blank(info->data_buff, (mtd->writesize + mtd->oobsize))) { exec_cmd = 0; break; } /* Second command setting for large pages */ if (mtd->writesize > PAGE_CHUNK_SIZE) { /* * Multiple page write uses the 'extended command' * field. This can be used to issue a command dispatch * or a naked-write depending on the current stage. */ info->ndcb0 |= NDCB0_CMD_TYPE(0x1) | NDCB0_LEN_OVRD | NDCB0_EXT_CMD_TYPE(ext_cmd_type); info->ndcb3 = info->chunk_size + info->oob_size; /* * This is the command dispatch that completes a chunked * page program operation. */ if (info->data_size == 0) { info->ndcb0 = NDCB0_CMD_TYPE(0x1) | NDCB0_EXT_CMD_TYPE(ext_cmd_type) | command; info->ndcb1 = 0; info->ndcb2 = 0; info->ndcb3 = 0; } } else { info->ndcb0 |= NDCB0_CMD_TYPE(0x1) | NDCB0_AUTO_RS | NDCB0_ST_ROW_EN | NDCB0_DBC | (NAND_CMD_PAGEPROG << 8) | NAND_CMD_SEQIN | addr_cycle; } break; case NAND_CMD_PARAM: info->buf_count = 256; info->ndcb0 |= NDCB0_CMD_TYPE(0) | NDCB0_ADDR_CYC(1) | NDCB0_LEN_OVRD | command; info->ndcb1 = (column & 0xFF); info->ndcb3 = 256; info->data_size = 256; break; case NAND_CMD_READID: info->buf_count = host->read_id_bytes; info->ndcb0 |= NDCB0_CMD_TYPE(3) | NDCB0_ADDR_CYC(1) | command; info->ndcb1 = (column & 0xFF); info->data_size = 8; break; case NAND_CMD_STATUS: info->buf_count = 1; info->ndcb0 |= NDCB0_CMD_TYPE(4) | NDCB0_ADDR_CYC(1) | command; info->data_size = 8; break; case NAND_CMD_ERASE1: info->ndcb0 |= NDCB0_CMD_TYPE(2) | NDCB0_AUTO_RS | NDCB0_ADDR_CYC(3) | NDCB0_DBC | (NAND_CMD_ERASE2 << 8) | NAND_CMD_ERASE1; info->ndcb1 = page_addr; info->ndcb2 = 0; break; case NAND_CMD_RESET: info->ndcb0 |= NDCB0_CMD_TYPE(5) | command; break; case NAND_CMD_ERASE2: exec_cmd = 0; break; default: exec_cmd = 0; dev_err(&info->pdev->dev, "non-supported command %x\n", command); break; } return exec_cmd; } static void nand_cmdfunc(struct mtd_info *mtd, unsigned command, int column, int page_addr) { struct pxa3xx_nand_host *host = mtd->priv; struct pxa3xx_nand_info *info = host->info_data; int exec_cmd; /* * if this is a x16 device ,then convert the input * "byte" address into a "word" address appropriate * for indexing a word-oriented device */ if (info->reg_ndcr & NDCR_DWIDTH_M) column /= 2; /* * There may be different NAND chip hooked to * different chip select, so check whether * chip select has been changed, if yes, reset the timing */ if (info->cs != host->cs) { info->cs = host->cs; nand_writel(info, NDTR0CS0, info->ndtr0cs0); nand_writel(info, NDTR1CS0, info->ndtr1cs0); } prepare_start_command(info, command); info->state = STATE_PREPARED; exec_cmd = prepare_set_command(info, command, 0, column, page_addr); if (exec_cmd) { init_completion(&info->cmd_complete); init_completion(&info->dev_ready); info->need_wait = 1; pxa3xx_nand_start(info); if (!wait_for_completion_timeout(&info->cmd_complete, CHIP_DELAY_TIMEOUT)) { dev_err(&info->pdev->dev, "Wait time out!!!\n"); /* Stop State Machine for next command cycle */ pxa3xx_nand_stop(info); } } info->state = STATE_IDLE; } static void nand_cmdfunc_extended(struct mtd_info *mtd, const unsigned command, int column, int page_addr) { struct pxa3xx_nand_host *host = mtd->priv; struct pxa3xx_nand_info *info = host->info_data; int exec_cmd, ext_cmd_type; /* * if this is a x16 device then convert the input * "byte" address into a "word" address appropriate * for indexing a word-oriented device */ if (info->reg_ndcr & NDCR_DWIDTH_M) column /= 2; /* * There may be different NAND chip hooked to * different chip select, so check whether * chip select has been changed, if yes, reset the timing */ if (info->cs != host->cs) { info->cs = host->cs; nand_writel(info, NDTR0CS0, info->ndtr0cs0); nand_writel(info, NDTR1CS0, info->ndtr1cs0); } /* Select the extended command for the first command */ switch (command) { case NAND_CMD_READ0: case NAND_CMD_READOOB: ext_cmd_type = EXT_CMD_TYPE_MONO; break; case NAND_CMD_SEQIN: ext_cmd_type = EXT_CMD_TYPE_DISPATCH; break; case NAND_CMD_PAGEPROG: ext_cmd_type = EXT_CMD_TYPE_NAKED_RW; break; default: ext_cmd_type = 0; break; } prepare_start_command(info, command); /* * Prepare the "is ready" completion before starting a command * transaction sequence. If the command is not executed the * completion will be completed, see below. * * We can do that inside the loop because the command variable * is invariant and thus so is the exec_cmd. */ info->need_wait = 1; init_completion(&info->dev_ready); do { info->state = STATE_PREPARED; exec_cmd = prepare_set_command(info, command, ext_cmd_type, column, page_addr); if (!exec_cmd) { info->need_wait = 0; complete(&info->dev_ready); break; } init_completion(&info->cmd_complete); pxa3xx_nand_start(info); if (!wait_for_completion_timeout(&info->cmd_complete, CHIP_DELAY_TIMEOUT)) { dev_err(&info->pdev->dev, "Wait time out!!!\n"); /* Stop State Machine for next command cycle */ pxa3xx_nand_stop(info); break; } /* Check if the sequence is complete */ if (info->data_size == 0 && command != NAND_CMD_PAGEPROG) break; /* * After a splitted program command sequence has issued * the command dispatch, the command sequence is complete. */ if (info->data_size == 0 && command == NAND_CMD_PAGEPROG && ext_cmd_type == EXT_CMD_TYPE_DISPATCH) break; if (command == NAND_CMD_READ0 || command == NAND_CMD_READOOB) { /* Last read: issue a 'last naked read' */ if (info->data_size == info->chunk_size) ext_cmd_type = EXT_CMD_TYPE_LAST_RW; else ext_cmd_type = EXT_CMD_TYPE_NAKED_RW; /* * If a splitted program command has no more data to transfer, * the command dispatch must be issued to complete. */ } else if (command == NAND_CMD_PAGEPROG && info->data_size == 0) { ext_cmd_type = EXT_CMD_TYPE_DISPATCH; } } while (1); info->state = STATE_IDLE; } static int pxa3xx_nand_write_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, const uint8_t *buf, int oob_required) { chip->write_buf(mtd, buf, mtd->writesize); chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); return 0; } static int pxa3xx_nand_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, uint8_t *buf, int oob_required, int page) { struct pxa3xx_nand_host *host = mtd->priv; struct pxa3xx_nand_info *info = host->info_data; chip->read_buf(mtd, buf, mtd->writesize); chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); if (info->retcode == ERR_CORERR && info->use_ecc) { mtd->ecc_stats.corrected += info->ecc_err_cnt; } else if (info->retcode == ERR_UNCORERR) { /* * for blank page (all 0xff), HW will calculate its ECC as * 0, which is different from the ECC information within * OOB, ignore such uncorrectable errors */ if (is_buf_blank(buf, mtd->writesize)) info->retcode = ERR_NONE; else mtd->ecc_stats.failed++; } return info->max_bitflips; } static uint8_t pxa3xx_nand_read_byte(struct mtd_info *mtd) { struct pxa3xx_nand_host *host = mtd->priv; struct pxa3xx_nand_info *info = host->info_data; char retval = 0xFF; if (info->buf_start < info->buf_count) /* Has just send a new command? */ retval = info->data_buff[info->buf_start++]; return retval; } static u16 pxa3xx_nand_read_word(struct mtd_info *mtd) { struct pxa3xx_nand_host *host = mtd->priv; struct pxa3xx_nand_info *info = host->info_data; u16 retval = 0xFFFF; if (!(info->buf_start & 0x01) && info->buf_start < info->buf_count) { retval = *((u16 *)(info->data_buff+info->buf_start)); info->buf_start += 2; } return retval; } static void pxa3xx_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) { struct pxa3xx_nand_host *host = mtd->priv; struct pxa3xx_nand_info *info = host->info_data; int real_len = min_t(size_t, len, info->buf_count - info->buf_start); memcpy(buf, info->data_buff + info->buf_start, real_len); info->buf_start += real_len; } static void pxa3xx_nand_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len) { struct pxa3xx_nand_host *host = mtd->priv; struct pxa3xx_nand_info *info = host->info_data; int real_len = min_t(size_t, len, info->buf_count - info->buf_start); memcpy(info->data_buff + info->buf_start, buf, real_len); info->buf_start += real_len; } static void pxa3xx_nand_select_chip(struct mtd_info *mtd, int chip) { return; } static int pxa3xx_nand_waitfunc(struct mtd_info *mtd, struct nand_chip *this) { struct pxa3xx_nand_host *host = mtd->priv; struct pxa3xx_nand_info *info = host->info_data; if (info->need_wait) { info->need_wait = 0; if (!wait_for_completion_timeout(&info->dev_ready, CHIP_DELAY_TIMEOUT)) { dev_err(&info->pdev->dev, "Ready time out!!!\n"); return NAND_STATUS_FAIL; } } /* pxa3xx_nand_send_command has waited for command complete */ if (this->state == FL_WRITING || this->state == FL_ERASING) { if (info->retcode == ERR_NONE) return 0; else return NAND_STATUS_FAIL; } return NAND_STATUS_READY; } static int pxa3xx_nand_config_flash(struct pxa3xx_nand_info *info, const struct pxa3xx_nand_flash *f) { struct platform_device *pdev = info->pdev; struct pxa3xx_nand_platform_data *pdata = dev_get_platdata(&pdev->dev); struct pxa3xx_nand_host *host = info->host[info->cs]; uint32_t ndcr = 0x0; /* enable all interrupts */ if (f->page_size != 2048 && f->page_size != 512) { dev_err(&pdev->dev, "Current only support 2048 and 512 size\n"); return -EINVAL; } if (f->flash_width != 16 && f->flash_width != 8) { dev_err(&pdev->dev, "Only support 8bit and 16 bit!\n"); return -EINVAL; } /* calculate flash information */ host->read_id_bytes = (f->page_size == 2048) ? 4 : 2; /* calculate addressing information */ host->col_addr_cycles = (f->page_size == 2048) ? 2 : 1; if (f->num_blocks * f->page_per_block > 65536) host->row_addr_cycles = 3; else host->row_addr_cycles = 2; ndcr |= (pdata->enable_arbiter) ? NDCR_ND_ARB_EN : 0; ndcr |= (host->col_addr_cycles == 2) ? NDCR_RA_START : 0; ndcr |= (f->page_per_block == 64) ? NDCR_PG_PER_BLK : 0; ndcr |= (f->page_size == 2048) ? NDCR_PAGE_SZ : 0; ndcr |= (f->flash_width == 16) ? NDCR_DWIDTH_M : 0; ndcr |= (f->dfc_width == 16) ? NDCR_DWIDTH_C : 0; ndcr |= NDCR_RD_ID_CNT(host->read_id_bytes); ndcr |= NDCR_SPARE_EN; /* enable spare by default */ info->reg_ndcr = ndcr; pxa3xx_nand_set_timing(host, f->timing); return 0; } static int pxa3xx_nand_detect_config(struct pxa3xx_nand_info *info) { /* * We set 0 by hard coding here, for we don't support keep_config * when there is more than one chip attached to the controller */ struct pxa3xx_nand_host *host = info->host[0]; uint32_t ndcr = nand_readl(info, NDCR); if (ndcr & NDCR_PAGE_SZ) { /* Controller's FIFO size */ info->chunk_size = 2048; host->read_id_bytes = 4; } else { info->chunk_size = 512; host->read_id_bytes = 2; } /* Set an initial chunk size */ info->reg_ndcr = ndcr & ~NDCR_INT_MASK; info->ndtr0cs0 = nand_readl(info, NDTR0CS0); info->ndtr1cs0 = nand_readl(info, NDTR1CS0); return 0; } #ifdef ARCH_HAS_DMA static int pxa3xx_nand_init_buff(struct pxa3xx_nand_info *info) { struct platform_device *pdev = info->pdev; int data_desc_offset = info->buf_size - sizeof(struct pxa_dma_desc); if (use_dma == 0) { info->data_buff = kmalloc(info->buf_size, GFP_KERNEL); if (info->data_buff == NULL) return -ENOMEM; return 0; } info->data_buff = dma_alloc_coherent(&pdev->dev, info->buf_size, &info->data_buff_phys, GFP_KERNEL); if (info->data_buff == NULL) { dev_err(&pdev->dev, "failed to allocate dma buffer\n"); return -ENOMEM; } info->data_desc = (void *)info->data_buff + data_desc_offset; info->data_desc_addr = info->data_buff_phys + data_desc_offset; info->data_dma_ch = pxa_request_dma("nand-data", DMA_PRIO_LOW, pxa3xx_nand_data_dma_irq, info); if (info->data_dma_ch < 0) { dev_err(&pdev->dev, "failed to request data dma\n"); dma_free_coherent(&pdev->dev, info->buf_size, info->data_buff, info->data_buff_phys); return info->data_dma_ch; } /* * Now that DMA buffers are allocated we turn on * DMA proper for I/O operations. */ info->use_dma = 1; return 0; } static void pxa3xx_nand_free_buff(struct pxa3xx_nand_info *info) { struct platform_device *pdev = info->pdev; if (info->use_dma) { pxa_free_dma(info->data_dma_ch); dma_free_coherent(&pdev->dev, info->buf_size, info->data_buff, info->data_buff_phys); } else { kfree(info->data_buff); } } #else static int pxa3xx_nand_init_buff(struct pxa3xx_nand_info *info) { info->data_buff = kmalloc(info->buf_size, GFP_KERNEL); if (info->data_buff == NULL) return -ENOMEM; return 0; } static void pxa3xx_nand_free_buff(struct pxa3xx_nand_info *info) { kfree(info->data_buff); } #endif static int pxa3xx_nand_sensing(struct pxa3xx_nand_info *info) { struct mtd_info *mtd; struct nand_chip *chip; int ret; mtd = info->host[info->cs]->mtd; chip = mtd->priv; /* use the common timing to make a try */ ret = pxa3xx_nand_config_flash(info, &builtin_flash_types[0]); if (ret) return ret; chip->cmdfunc(mtd, NAND_CMD_RESET, 0, 0); ret = chip->waitfunc(mtd, chip); if (ret & NAND_STATUS_FAIL) return -ENODEV; return 0; } static int pxa_ecc_init(struct pxa3xx_nand_info *info, struct nand_ecc_ctrl *ecc, int strength, int ecc_stepsize, int page_size) { if (strength == 1 && ecc_stepsize == 512 && page_size == 2048) { info->chunk_size = 2048; info->spare_size = 40; info->ecc_size = 24; ecc->mode = NAND_ECC_HW; ecc->size = 512; ecc->strength = 1; } else if (strength == 1 && ecc_stepsize == 512 && page_size == 512) { info->chunk_size = 512; info->spare_size = 8; info->ecc_size = 8; ecc->mode = NAND_ECC_HW; ecc->size = 512; ecc->strength = 1; /* * Required ECC: 4-bit correction per 512 bytes * Select: 16-bit correction per 2048 bytes */ } else if (strength == 4 && ecc_stepsize == 512 && page_size == 2048) { info->ecc_bch = 1; info->chunk_size = 2048; info->spare_size = 32; info->ecc_size = 32; ecc->mode = NAND_ECC_HW; ecc->size = info->chunk_size; ecc->layout = &ecc_layout_2KB_bch4bit; ecc->strength = 16; } else if (strength == 4 && ecc_stepsize == 512 && page_size == 4096) { info->ecc_bch = 1; info->chunk_size = 2048; info->spare_size = 32; info->ecc_size = 32; ecc->mode = NAND_ECC_HW; ecc->size = info->chunk_size; ecc->layout = &ecc_layout_4KB_bch4bit; ecc->strength = 16; /* * Required ECC: 8-bit correction per 512 bytes * Select: 16-bit correction per 1024 bytes */ } else if (strength == 8 && ecc_stepsize == 512 && page_size == 4096) { info->ecc_bch = 1; info->chunk_size = 1024; info->spare_size = 0; info->ecc_size = 32; ecc->mode = NAND_ECC_HW; ecc->size = info->chunk_size; ecc->layout = &ecc_layout_4KB_bch8bit; ecc->strength = 16; } else { dev_err(&info->pdev->dev, "ECC strength %d at page size %d is not supported\n", strength, page_size); return -ENODEV; } dev_info(&info->pdev->dev, "ECC strength %d, ECC step size %d\n", ecc->strength, ecc->size); return 0; } static int pxa3xx_nand_scan(struct mtd_info *mtd) { struct pxa3xx_nand_host *host = mtd->priv; struct pxa3xx_nand_info *info = host->info_data; struct platform_device *pdev = info->pdev; struct pxa3xx_nand_platform_data *pdata = dev_get_platdata(&pdev->dev); struct nand_flash_dev pxa3xx_flash_ids[2], *def = NULL; const struct pxa3xx_nand_flash *f = NULL; struct nand_chip *chip = mtd->priv; uint32_t id = -1; uint64_t chipsize; int i, ret, num; uint16_t ecc_strength, ecc_step; if (pdata->keep_config && !pxa3xx_nand_detect_config(info)) goto KEEP_CONFIG; /* Set a default chunk size */ info->chunk_size = 512; ret = pxa3xx_nand_sensing(info); if (ret) { dev_info(&info->pdev->dev, "There is no chip on cs %d!\n", info->cs); return ret; } chip->cmdfunc(mtd, NAND_CMD_READID, 0, 0); id = *((uint16_t *)(info->data_buff)); if (id != 0) dev_info(&info->pdev->dev, "Detect a flash id %x\n", id); else { dev_warn(&info->pdev->dev, "Read out ID 0, potential timing set wrong!!\n"); return -EINVAL; } num = ARRAY_SIZE(builtin_flash_types) + pdata->num_flash - 1; for (i = 0; i < num; i++) { if (i < pdata->num_flash) f = pdata->flash + i; else f = &builtin_flash_types[i - pdata->num_flash + 1]; /* find the chip in default list */ if (f->chip_id == id) break; } if (i >= (ARRAY_SIZE(builtin_flash_types) + pdata->num_flash - 1)) { dev_err(&info->pdev->dev, "ERROR!! flash not defined!!!\n"); return -EINVAL; } ret = pxa3xx_nand_config_flash(info, f); if (ret) { dev_err(&info->pdev->dev, "ERROR! Configure failed\n"); return ret; } memset(pxa3xx_flash_ids, 0, sizeof(pxa3xx_flash_ids)); pxa3xx_flash_ids[0].name = f->name; pxa3xx_flash_ids[0].dev_id = (f->chip_id >> 8) & 0xffff; pxa3xx_flash_ids[0].pagesize = f->page_size; chipsize = (uint64_t)f->num_blocks * f->page_per_block * f->page_size; pxa3xx_flash_ids[0].chipsize = chipsize >> 20; pxa3xx_flash_ids[0].erasesize = f->page_size * f->page_per_block; if (f->flash_width == 16) pxa3xx_flash_ids[0].options = NAND_BUSWIDTH_16; pxa3xx_flash_ids[1].name = NULL; def = pxa3xx_flash_ids; KEEP_CONFIG: if (info->reg_ndcr & NDCR_DWIDTH_M) chip->options |= NAND_BUSWIDTH_16; /* Device detection must be done with ECC disabled */ if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370) nand_writel(info, NDECCCTRL, 0x0); if (nand_scan_ident(mtd, 1, def)) return -ENODEV; if (pdata->flash_bbt) { /* * We'll use a bad block table stored in-flash and don't * allow writing the bad block marker to the flash. */ chip->bbt_options |= NAND_BBT_USE_FLASH | NAND_BBT_NO_OOB_BBM; chip->bbt_td = &bbt_main_descr; chip->bbt_md = &bbt_mirror_descr; } /* * If the page size is bigger than the FIFO size, let's check * we are given the right variant and then switch to the extended * (aka splitted) command handling, */ if (mtd->writesize > PAGE_CHUNK_SIZE) { if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370) { chip->cmdfunc = nand_cmdfunc_extended; } else { dev_err(&info->pdev->dev, "unsupported page size on this variant\n"); return -ENODEV; } } if (pdata->ecc_strength && pdata->ecc_step_size) { ecc_strength = pdata->ecc_strength; ecc_step = pdata->ecc_step_size; } else { ecc_strength = chip->ecc_strength_ds; ecc_step = chip->ecc_step_ds; } /* Set default ECC strength requirements on non-ONFI devices */ if (ecc_strength < 1 && ecc_step < 1) { ecc_strength = 1; ecc_step = 512; } ret = pxa_ecc_init(info, &chip->ecc, ecc_strength, ecc_step, mtd->writesize); if (ret) return ret; /* calculate addressing information */ if (mtd->writesize >= 2048) host->col_addr_cycles = 2; else host->col_addr_cycles = 1; /* release the initial buffer */ kfree(info->data_buff); /* allocate the real data + oob buffer */ info->buf_size = mtd->writesize + mtd->oobsize; ret = pxa3xx_nand_init_buff(info); if (ret) return ret; info->oob_buff = info->data_buff + mtd->writesize; if ((mtd->size >> chip->page_shift) > 65536) host->row_addr_cycles = 3; else host->row_addr_cycles = 2; return nand_scan_tail(mtd); } static int alloc_nand_resource(struct platform_device *pdev) { struct pxa3xx_nand_platform_data *pdata; struct pxa3xx_nand_info *info; struct pxa3xx_nand_host *host; struct nand_chip *chip = NULL; struct mtd_info *mtd; struct resource *r; int ret, irq, cs; pdata = dev_get_platdata(&pdev->dev); if (pdata->num_cs <= 0) return -ENODEV; info = devm_kzalloc(&pdev->dev, sizeof(*info) + (sizeof(*mtd) + sizeof(*host)) * pdata->num_cs, GFP_KERNEL); if (!info) return -ENOMEM; info->pdev = pdev; info->variant = pxa3xx_nand_get_variant(pdev); for (cs = 0; cs < pdata->num_cs; cs++) { mtd = (struct mtd_info *)((unsigned int)&info[1] + (sizeof(*mtd) + sizeof(*host)) * cs); chip = (struct nand_chip *)(&mtd[1]); host = (struct pxa3xx_nand_host *)chip; info->host[cs] = host; host->mtd = mtd; host->cs = cs; host->info_data = info; mtd->priv = host; mtd->owner = THIS_MODULE; chip->ecc.read_page = pxa3xx_nand_read_page_hwecc; chip->ecc.write_page = pxa3xx_nand_write_page_hwecc; chip->controller = &info->controller; chip->waitfunc = pxa3xx_nand_waitfunc; chip->select_chip = pxa3xx_nand_select_chip; chip->read_word = pxa3xx_nand_read_word; chip->read_byte = pxa3xx_nand_read_byte; chip->read_buf = pxa3xx_nand_read_buf; chip->write_buf = pxa3xx_nand_write_buf; chip->options |= NAND_NO_SUBPAGE_WRITE; chip->cmdfunc = nand_cmdfunc; } spin_lock_init(&chip->controller->lock); init_waitqueue_head(&chip->controller->wq); info->clk = devm_clk_get(&pdev->dev, NULL); if (IS_ERR(info->clk)) { dev_err(&pdev->dev, "failed to get nand clock\n"); return PTR_ERR(info->clk); } ret = clk_prepare_enable(info->clk); if (ret < 0) return ret; if (use_dma) { /* * This is a dirty hack to make this driver work from * devicetree bindings. It can be removed once we have * a prober DMA controller framework for DT. */ if (pdev->dev.of_node && of_machine_is_compatible("marvell,pxa3xx")) { info->drcmr_dat = 97; info->drcmr_cmd = 99; } else { r = platform_get_resource(pdev, IORESOURCE_DMA, 0); if (r == NULL) { dev_err(&pdev->dev, "no resource defined for data DMA\n"); ret = -ENXIO; goto fail_disable_clk; } info->drcmr_dat = r->start; r = platform_get_resource(pdev, IORESOURCE_DMA, 1); if (r == NULL) { dev_err(&pdev->dev, "no resource defined for cmd DMA\n"); ret = -ENXIO; goto fail_disable_clk; } info->drcmr_cmd = r->start; } } irq = platform_get_irq(pdev, 0); if (irq < 0) { dev_err(&pdev->dev, "no IRQ resource defined\n"); ret = -ENXIO; goto fail_disable_clk; } r = platform_get_resource(pdev, IORESOURCE_MEM, 0); info->mmio_base = devm_ioremap_resource(&pdev->dev, r); if (IS_ERR(info->mmio_base)) { ret = PTR_ERR(info->mmio_base); goto fail_disable_clk; } info->mmio_phys = r->start; /* Allocate a buffer to allow flash detection */ info->buf_size = INIT_BUFFER_SIZE; info->data_buff = kmalloc(info->buf_size, GFP_KERNEL); if (info->data_buff == NULL) { ret = -ENOMEM; goto fail_disable_clk; } /* initialize all interrupts to be disabled */ disable_int(info, NDSR_MASK); ret = request_threaded_irq(irq, pxa3xx_nand_irq, pxa3xx_nand_irq_thread, IRQF_ONESHOT, pdev->name, info); if (ret < 0) { dev_err(&pdev->dev, "failed to request IRQ\n"); goto fail_free_buf; } platform_set_drvdata(pdev, info); return 0; fail_free_buf: free_irq(irq, info); kfree(info->data_buff); fail_disable_clk: clk_disable_unprepare(info->clk); return ret; } static int pxa3xx_nand_remove(struct platform_device *pdev) { struct pxa3xx_nand_info *info = platform_get_drvdata(pdev); struct pxa3xx_nand_platform_data *pdata; int irq, cs; if (!info) return 0; pdata = dev_get_platdata(&pdev->dev); irq = platform_get_irq(pdev, 0); if (irq >= 0) free_irq(irq, info); pxa3xx_nand_free_buff(info); clk_disable_unprepare(info->clk); for (cs = 0; cs < pdata->num_cs; cs++) nand_release(info->host[cs]->mtd); return 0; } static int pxa3xx_nand_probe_dt(struct platform_device *pdev) { struct pxa3xx_nand_platform_data *pdata; struct device_node *np = pdev->dev.of_node; const struct of_device_id *of_id = of_match_device(pxa3xx_nand_dt_ids, &pdev->dev); if (!of_id) return 0; pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); if (!pdata) return -ENOMEM; if (of_get_property(np, "marvell,nand-enable-arbiter", NULL)) pdata->enable_arbiter = 1; if (of_get_property(np, "marvell,nand-keep-config", NULL)) pdata->keep_config = 1; of_property_read_u32(np, "num-cs", &pdata->num_cs); pdata->flash_bbt = of_get_nand_on_flash_bbt(np); pdata->ecc_strength = of_get_nand_ecc_strength(np); if (pdata->ecc_strength < 0) pdata->ecc_strength = 0; pdata->ecc_step_size = of_get_nand_ecc_step_size(np); if (pdata->ecc_step_size < 0) pdata->ecc_step_size = 0; pdev->dev.platform_data = pdata; return 0; } static int pxa3xx_nand_probe(struct platform_device *pdev) { struct pxa3xx_nand_platform_data *pdata; struct mtd_part_parser_data ppdata = {}; struct pxa3xx_nand_info *info; int ret, cs, probe_success; #ifndef ARCH_HAS_DMA if (use_dma) { use_dma = 0; dev_warn(&pdev->dev, "This platform can't do DMA on this device\n"); } #endif ret = pxa3xx_nand_probe_dt(pdev); if (ret) return ret; pdata = dev_get_platdata(&pdev->dev); if (!pdata) { dev_err(&pdev->dev, "no platform data defined\n"); return -ENODEV; } ret = alloc_nand_resource(pdev); if (ret) { dev_err(&pdev->dev, "alloc nand resource failed\n"); return ret; } info = platform_get_drvdata(pdev); probe_success = 0; for (cs = 0; cs < pdata->num_cs; cs++) { struct mtd_info *mtd = info->host[cs]->mtd; /* * The mtd name matches the one used in 'mtdparts' kernel * parameter. This name cannot be changed or otherwise * user's mtd partitions configuration would get broken. */ mtd->name = "pxa3xx_nand-0"; info->cs = cs; ret = pxa3xx_nand_scan(mtd); if (ret) { dev_warn(&pdev->dev, "failed to scan nand at cs %d\n", cs); continue; } ppdata.of_node = pdev->dev.of_node; ret = mtd_device_parse_register(mtd, NULL, &ppdata, pdata->parts[cs], pdata->nr_parts[cs]); if (!ret) probe_success = 1; } if (!probe_success) { pxa3xx_nand_remove(pdev); return -ENODEV; } return 0; } #ifdef CONFIG_PM static int pxa3xx_nand_suspend(struct platform_device *pdev, pm_message_t state) { struct pxa3xx_nand_info *info = platform_get_drvdata(pdev); struct pxa3xx_nand_platform_data *pdata; struct mtd_info *mtd; int cs; pdata = dev_get_platdata(&pdev->dev); if (info->state) { dev_err(&pdev->dev, "driver busy, state = %d\n", info->state); return -EAGAIN; } for (cs = 0; cs < pdata->num_cs; cs++) { mtd = info->host[cs]->mtd; mtd_suspend(mtd); } return 0; } static int pxa3xx_nand_resume(struct platform_device *pdev) { struct pxa3xx_nand_info *info = platform_get_drvdata(pdev); struct pxa3xx_nand_platform_data *pdata; struct mtd_info *mtd; int cs; pdata = dev_get_platdata(&pdev->dev); /* We don't want to handle interrupt without calling mtd routine */ disable_int(info, NDCR_INT_MASK); /* * Directly set the chip select to a invalid value, * then the driver would reset the timing according * to current chip select at the beginning of cmdfunc */ info->cs = 0xff; /* * As the spec says, the NDSR would be updated to 0x1800 when * doing the nand_clk disable/enable. * To prevent it damaging state machine of the driver, clear * all status before resume */ nand_writel(info, NDSR, NDSR_MASK); for (cs = 0; cs < pdata->num_cs; cs++) { mtd = info->host[cs]->mtd; mtd_resume(mtd); } return 0; } #else #define pxa3xx_nand_suspend NULL #define pxa3xx_nand_resume NULL #endif static struct platform_driver pxa3xx_nand_driver = { .driver = { .name = "pxa3xx-nand", .of_match_table = pxa3xx_nand_dt_ids, }, .probe = pxa3xx_nand_probe, .remove = pxa3xx_nand_remove, .suspend = pxa3xx_nand_suspend, .resume = pxa3xx_nand_resume, }; module_platform_driver(pxa3xx_nand_driver); MODULE_LICENSE("GPL"); MODULE_DESCRIPTION("PXA3xx NAND controller driver");