# # PHY Layer Configuration # menuconfig PHYLIB tristate "PHY Device support and infrastructure" depends on NETDEVICES help Ethernet controllers are usually attached to PHY devices. This option provides infrastructure for managing PHY devices. if PHYLIB comment "MII PHY device drivers" config AT803X_PHY tristate "Drivers for Atheros AT803X PHYs" ---help--- Currently supports the AT8030 and AT8035 model config AMD_PHY tristate "Drivers for the AMD PHYs" ---help--- Currently supports the am79c874 config AMD_XGBE_PHY tristate "Driver for the AMD 10GbE (amd-xgbe) PHYs" depends on (OF || ACPI) && HAS_IOMEM depends on ARM64 || COMPILE_TEST ---help--- Currently supports the AMD 10GbE PHY config MARVELL_PHY tristate "Drivers for Marvell PHYs" ---help--- Currently has a driver for the 88E1011S config DAVICOM_PHY tristate "Drivers for Davicom PHYs" ---help--- Currently supports dm9161e and dm9131 config QSEMI_PHY tristate "Drivers for Quality Semiconductor PHYs" ---help--- Currently supports the qs6612 config LXT_PHY tristate "Drivers for the Intel LXT PHYs" ---help--- Currently supports the lxt970, lxt971 config CICADA_PHY tristate "Drivers for the Cicada PHYs" ---help--- Currently supports the cis8204 config VITESSE_PHY tristate "Drivers for the Vitesse PHYs" ---help--- Currently supports the vsc8244 config SMSC_PHY tristate "Drivers for SMSC PHYs" ---help--- Currently supports the LAN83C185, LAN8187 and LAN8700 PHYs config BROADCOM_PHY tristate "Drivers for Broadcom PHYs" ---help--- Currently supports the BCM5411, BCM5421, BCM5461, BCM54616S, BCM5464, BCM5481 and BCM5482 PHYs. config BCM63XX_PHY tristate "Drivers for Broadcom 63xx SOCs internal PHY" depends on BCM63XX ---help--- Currently supports the 6348 and 6358 PHYs. config BCM7XXX_PHY tristate "Drivers for Broadcom 7xxx SOCs internal PHYs" ---help--- Currently supports the BCM7366, BCM7439, BCM7445, and 40nm and 65nm generation of BCM7xxx Set Top Box SoCs. config BCM87XX_PHY tristate "Driver for Broadcom BCM8706 and BCM8727 PHYs" help Currently supports the BCM8706 and BCM8727 10G Ethernet PHYs. config ICPLUS_PHY tristate "Drivers for ICPlus PHYs" ---help--- Currently supports the IP175C and IP1001 PHYs. config REALTEK_PHY tristate "Drivers for Realtek PHYs" ---help--- Supports the Realtek 821x PHY. config NATIONAL_PHY tristate "Drivers for National Semiconductor PHYs" ---help--- Currently supports the DP83865 PHY. config STE10XP tristate "Driver for STMicroelectronics STe10Xp PHYs" ---help--- This is the driver for the STe100p and STe101p PHYs. config LSI_ET1011C_PHY tristate "Driver for LSI ET1011C PHY" ---help--- Supports the LSI ET1011C PHY. config MICREL_PHY tristate "Driver for Micrel PHYs" ---help--- Supports the KSZ9021, VSC8201, KS8001 PHYs. config FIXED_PHY tristate "Driver for MDIO Bus/PHY emulation with fixed speed/link PHYs" depends on PHYLIB ---help--- Adds the platform "fixed" MDIO Bus to cover the boards that use PHYs that are not connected to the real MDIO bus. Currently tested with mpc866ads and mpc8349e-mitx. config MDIO_BITBANG tristate "Support for bitbanged MDIO buses" help This module implements the MDIO bus protocol in software, for use by low level drivers that export the ability to drive the relevant pins. If in doubt, say N. config MDIO_GPIO tristate "Support for GPIO lib-based bitbanged MDIO buses" depends on MDIO_BITBANG && GPIOLIB ---help--- Supports GPIO lib-based MDIO busses. To compile this driver as a module, choose M here: the module will be called mdio-gpio. config MDIO_OCTEON tristate "Support for MDIO buses on Octeon SOCs" depends on CAVIUM_OCTEON_SOC default y help This module provides a driver for the Octeon MDIO busses. It is required by the Octeon Ethernet device drivers. If in doubt, say Y. config MDIO_SUN4I tristate "Allwinner sun4i MDIO interface support" depends on ARCH_SUNXI help This driver supports the MDIO interface found in the network interface units of the Allwinner SoC that have an EMAC (A10, A12, A10s, etc.) config MDIO_MOXART tristate "MOXA ART MDIO interface support" depends on ARCH_MOXART help This driver supports the MDIO interface found in the network interface units of the MOXA ART SoC config MDIO_BUS_MUX tristate depends on OF_MDIO help This module provides a driver framework for MDIO bus multiplexers which connect one of several child MDIO busses to a parent bus. Switching between child busses is done by device specific drivers. config MDIO_BUS_MUX_GPIO tristate "Support for GPIO controlled MDIO bus multiplexers" depends on OF_GPIO && OF_MDIO select MDIO_BUS_MUX help This module provides a driver for MDIO bus multiplexers that are controlled via GPIO lines. The multiplexer connects one of several child MDIO busses to a parent bus. Child bus selection is under the control of GPIO lines. config MDIO_BUS_MUX_MMIOREG tristate "Support for MMIO device-controlled MDIO bus multiplexers" depends on OF_MDIO select MDIO_BUS_MUX help This module provides a driver for MDIO bus multiplexers that are controlled via a simple memory-mapped device, like an FPGA. The multiplexer connects one of several child MDIO busses to a parent bus. Child bus selection is under the control of one of the FPGA's registers. Currently, only 8-bit registers are supported. config MDIO_BCM_UNIMAC tristate "Broadcom UniMAC MDIO bus controller" depends on HAS_IOMEM help This module provides a driver for the Broadcom UniMAC MDIO busses. This hardware can be found in the Broadcom GENET Ethernet MAC controllers as well as some Broadcom Ethernet switches such as the Starfighter 2 switches. endif # PHYLIB config MICREL_KS8995MA tristate "Micrel KS8995MA 5-ports 10/100 managed Ethernet switch" depends on SPI