#include "47622.dtsi"
#include "../bcm_voice.dtsi"

/ {
    memory_controller {
        memcfg = <(BP_DDR_SPEED_933_13_13_13  | \
                   BP_DDR_TOTAL_SIZE_512MB    | \
                   BP_DDR_DEVICE_WIDTH_16     | \
                   BP_DDR_TOTAL_WIDTH_16BIT   | \
                   BP_DDR_SSC_CONFIG_1)>;
    };

	buttons {
		compatible = "brcm,buttons";
		ses_button {
			ext_irq = <&bca_extintr 4 BCA_GPIO_ACTIVE_LOW (BCA_EXTINTR_TYPE_LOW_LEVEL | BCA_EXTINTR_TYPE_SENSE_EDGE)>;
			release {
				ses_short_period = <0>;
				ses_long_period = <3>;
			};
		};
	};

	switch_sf2:0 {
	};
};

&i2c {
	#address-cells = <1>;
	#size-cells = <0>;
	codec_playback:codec_palyback@18{
		compatible = "ti,tlv320dac3203";
		reg = <0x18>;
	};
	codec_capture:codec_capture@19{
		compatible = "ti,tlv320adc3101";
		reg = <0x19>;
	};
};

&sysport {
	compatible = "brcm,bcmbca-systemport-v2.0";
	reg-names =
		"systemport-rbuf-base",
		"systemport-rdma-base",
		"systemport-tdma-base",
		"systemport-umac-base",
		"systemport-topctrl-base",
		"systemport1-rbuf-base",
		"systemport1-rdma-base",
		"systemport1-tdma-base",
		"systemport1-umac-base",
		"systemport1-topctrl-base",
		"systemport-switchmdio-base",
		"sphy-ctrl",
		"phy-test-ctrl";
	reg =   <0x80400400 0x14>,
			<0x80402000 0x1300>,
			<0x80404000 0x8ff>,
			<0x80400800 0x350>,
			<0x80400000 0x40>,
		    <0x80500400 0x14>,
			<0x80502000 0x1300>,
			<0x80504000 0x8ff>,
			<0x80500800 0x350>,
			<0x80500000 0x40>,
			<0x80411300 0x10>,
			<0x804110c0 0x04>,
			<0x804110bc 0x04>;
	phy_base = <0x8>;
	phy_wkard_timeout = <25000>;
	ethsw = <&switch_sf2>;
};

&usb_ctrl {
	pinctrl-names="default";
	pinctrl-0 = <&usb0_pwr_pins &usb1_pwr_pins>;
	pwron-bias-pull-up;
	status = "okay";
};

&usb0_ehci {
	status = "okay";
};

&usb1_ehci {
	status = "okay";
};

&usb0_ohci {
	status = "okay";
};

&usb1_ohci {
	status = "okay";
};
&bcm_voice{
	sliclist = SLICSLAC_LIST_COMMON_NOFXO;
 };

&hsspi {
	voice0 {
		pinctrl-0 = <&spim_ss1_b_pin_76>;
		pinctrl-names = "default";
		compatible = "bcm-spi-voice";
		reg = <1>; /* chip select 1 */
		spi-max-frequency = <1024000>;
		reset-gpio = <&gpioc 26 GPIO_ACTIVE_LOW>;
		spi-index = <0>;/* voice header index */
	};
	voice1 {
		pinctrl-0 = <&spim_ss2_b_pin_10>;
		pinctrl-names = "default";
		compatible = "bcm-spi-voice";
		reg = <2>; /* chip select 2 */
		spi-max-frequency = <1024000>;
		/*reset-gpio = NA*/
		spi-index = <1>;/* voice header index */
	};
};

&mdio {
	phy8:8 {
		status = "okay";
	};

	phy_serdes0:6 {
		phy-extswitch;
		status = "okay";
	};

	/* PHYs on external SF2 switch */
	sf2_gphy0:0 {
		compatible = "brcm,bcaphy";
		phy-type = "EGPHY";
		reg = <0>;
		status = "okay";
	};
	sf2_gphy1:1 {
		compatible = "brcm,bcaphy";
		phy-type = "EGPHY";
		reg = <1>;
		status = "okay";
	};
	sf2_gphy2:2 {
		compatible = "brcm,bcaphy";
		phy-type = "EGPHY";
		reg = <2>;
		status = "okay";
	};
	sf2_gphy3:3 {
		compatible = "brcm,bcaphy";
		phy-type = "EGPHY";
		reg = <3>;
		status = "okay";
	};
};

&switch_sf2 {
	unit = <1>;
	sw-type = "SF2_SW";

	compatible = "brcm,bcmbca-extsw";
	pinctrl-0 = <&a_rgmii_mdc_pin_68 &a_rgmii_mdio_pin_69 >;
	pinctrl-names="default";
	reg-names ="systemport-serdes-cntrl";
	reg = <0x804110a8 0x8>;
	extswsgmii_addr = <0x6>;
	switch-reset = <&gpioc 10 GPIO_ACTIVE_LOW>;

	ports {
		#address-cells = <1>;
		#size-cells = <0>;

		sf2_port0@0 {
			phy-handle = <&sf2_gphy0>;
			reg = <0>;
			mac-type = "SF2MAC";
			phy-mode = "gmii";
			gmii-direct;
			status = "okay";
		};
		sf2_port1@1 {
			phy-handle = <&sf2_gphy1>;
			reg = <1>;
			mac-type = "SF2MAC";
			phy-mode = "gmii";
			gmii-direct;
			status = "okay";
		};
		sf2_port2@2 {
			phy-handle = <&sf2_gphy2>;
			reg = <2>;
			mac-type = "SF2MAC";
			phy-mode = "gmii";
			gmii-direct;
			status = "okay";
		};
		sf2_port3@3 {
			phy-handle = <&sf2_gphy3>;
			reg = <3>;
			mac-type = "SF2MAC";
			phy-mode = "gmii";
			gmii-direct;
			status = "okay";
		};
		sf2_port8@8 {
			management;                     /* sf2.p8 <--> sysp.p1 */
			reg = <8>;
			mac-type = "SF2MAC";
			shrink-ipg;
			phy-mode = "gmii";
			gmii-direct;
			status = "okay";
		};
	};
};

&switch0 {
	pinctrl-names = "default"; 
	pinctrl-0 = <&a_rgmii_mdc_pin_68 &a_rgmii_mdio_pin_69>; 

	ports {
		/* fixed port configuration */
		sysp_port0@0 {
			phy-handle = <&phy8>;
			status = "okay";
		};
		sysp_port1@1 {
			phy-handle = <&phy_serdes0>;
			link = <&switch_sf2>;           /* sysp.p1 <--> sf2.p8 */
			shrink-ipg;
			status = "okay";
		};
	};
};