#include "63146.dtsi"
#include "../bcm_voice.dtsi"

/ {
	memory_controller {
		memcfg = <(BP_DDR_TYPE_DDR4        | \
			BP_DDR_SPEED_1600_22_22_22 | \
			BP_DDR_TOTAL_SIZE_1024MB   | \
			BP_DDR_DEVICE_WIDTH_16     | \
			BP_DDR_TOTAL_WIDTH_16BIT   | \
			BP_DDR_63146_DEFAULT)>;
	};

	buttons {
		compatible = "brcm,buttons";
		reset_button {
			ext_irq = <&bca_extintr 15 BCA_GPIO_ACTIVE_LOW (BCA_EXTINTR_TYPE_LOW_LEVEL | BCA_EXTINTR_TYPE_SENSE_EDGE)>;
			press {
				print = "Button Press -- Hold for 5s to do restore to default";
			};
			hold {
				rst_to_dflt = <5>;
			};
			release {
				reset = <0>;
			};	
		};
		ses_button {
			ext_irq = <&bca_extintr 1 BCA_GPIO_ACTIVE_LOW (BCA_EXTINTR_TYPE_LOW_LEVEL | BCA_EXTINTR_TYPE_SENSE_EDGE)>;
			release {
				ses_short_period = <0>;
				ses_long_period = <3>;
			};
		};
	};
};

&nand {
	write-protect = <1>;
};

&sdhci {
	pinctrl-names = "default";
	pinctrl-0 = <&emmc_ctrl_pins &data_pins>;
	status = "okay";
};

#if defined(CONFIG_BCM_PCIE_HCD) || defined(CONFIG_BCM_PCIE_HCD_MODULE)
&pcie0 {
	status = "okay";
};
&pcie1 {
	status = "okay";
};
&pcie2 {
	status = "okay";
};
#endif //#if defined(CONFIG_BCM_PCIE_HCD) || defined(CONFIG_BCM_PCIE_HCD_MODULE)

&usb_ctrl {
    pinctrl-names = "default";
    pinctrl-0 = <&usb0_pwr_pins &usb1_pwr_pins>;
	status = "okay";
	xhci-enable;
};
&usb0_xhci {
	status = "okay";
};

&i2c0 {
	status = "okay";
};
&i2c1 {
	status = "okay";
};

&mdio {
	phy1:1 {
		status = "okay";
	};

	phy2:2 {
		status = "okay";
	};

	phy3:3 {
		status = "okay";
	};

	phy4:4 {
		status = "okay";
	};

	phy5:5 {
		status = "okay";
	};

	phy_rgmii: rgmii {
		status = "disabled";
	};

	phy_serdes0:7 {
		status = "okay";
	};

	phy_serdes1:8 {
		status = "okay";
	};
};

&switch0 {
	ports {
		port0@0 {
            network-leds = <&led8 &led9>;
			status = "okay";
		};

		port1@1 {
            network-leds = <&led6 &led7>;
			status = "okay";
		};

		port2@2 {
            network-leds = <&led4 &led5>;
			status = "okay";
		};

		port3@3 {
            network-leds = <&led2 &led3>;
			status = "okay";
		};

		port4@4 {
            network-leds = <&led0 &led1>;
			status = "okay";
		};

		port6@6 {
			status = "okay";
		};

		port7@7 {
			status = "okay";
		};
	};
};

&legacy_leds {
	adsl-led = <&led14>;
	sec-adsl-led = <&led13>;
	wan-data-led = <&led15>;
	voip1-ok-led = <&led12>;
	voip2-ok-led = <&led11>;
	wl-sess-led = <&led10>;
};

&led_ctrl {
    pinctrl-names = "default";
    pinctrl-0 = <&ser_led_clk_pin_6 &ser_led_data_pin_8 &ser_led_mask_pin_11>;
    serial-shifters-installed = <2>;
    serial-data-polarity-high;
    led0: serial-port_4-led_2 {
        active_high;
        activity = <LED_SPEED_GBE>;
        crossbar-output = <0>;
        status = "okay";
    };
    led1: serial-port_4-led_0 {
        active_high;
        link = <(LED_SPEED_100|LED_SPEED_1G)>;
        crossbar-output = <1>;
        status = "okay";
    };
    led2: serial-port_3-led_2 {
        active_high;
        activity = <LED_SPEED_GBE>;
        crossbar-output = <2>;
        status = "okay";
    };
    led3: serial-port_3-led_0 {
        active_high;
        link = <(LED_SPEED_100|LED_SPEED_1G)>;
        crossbar-output = <3>;
        status = "okay";
    };
    led4: serial-port_2-led_2 {
        active_high;
        activity = <LED_SPEED_GBE>;
        crossbar-output = <4>;
        status = "okay";
    };
    led5: serial-port_2-led_0 {
        active_high;
        link = <(LED_SPEED_100|LED_SPEED_1G)>;
        crossbar-output = <5>;
        status = "okay";
    };
    led6: serial-port_1-led_2 {
        active_high;
        activity = <LED_SPEED_GBE>;
        crossbar-output = <6>;
        status = "okay";
    };
    led7: serial-port_1-led_0 {
        active_high;
        link = <(LED_SPEED_100|LED_SPEED_1G)>;
        crossbar-output = <7>;
        status = "okay";
    };
    led8: serial-port_0-led_2 {
        active_high;
        activity = <LED_SPEED_GBE>;
        crossbar-output = <8>;
        status = "okay";
    };
    led9: serial-port_0-led_0 {
        active_high;
        link = <(LED_SPEED_100|LED_SPEED_1G)>;
        crossbar-output = <9>;
        status = "okay";
    };
    led10: sw_serial_led_1 {
        active_high; 
        label = "WiFi";
        crossbar-output = <10>;
        status = "okay";
    };
    led11: sw_serial_led_4 {
        active_high; 
        label = "VOIP_2";
        crossbar-output = <11>;
        status = "okay";
    };
    led12: sw_serial_led_7 {
        active_high; 
        label = "VOIP_1";
        crossbar-output = <12>;
        status = "okay";
    };
    led13: sw_serial_led_10 {
        active_high; 
        label = "DSL_2";
        crossbar-output = <13>;
        status = "okay";
    };
    led14: sw_serial_led_13 {
        active_high; 
        label = "DSL_1";
        crossbar-output = <14>;
        status = "okay";
    };
    led15: serial_dsl_act_0 {
        active_high; 
        label = "INET";
        crossbar-output = <15>;
        status = "okay";
    };
};
&bcm_voice{
	sliclist = SLICSLAC_LIST_COMMON_NOFXO;
 };

&hsspi {
	voice0 {
		pinctrl-0 = <&hs_spim_ss_1_b_pin_20>;
		pinctrl-names = "default";
		compatible = "bcm-spi-voice";
		reg = <1>; /* chip select 1 */
		spi-max-frequency = <1024000>;
		reset-gpio = <&gpioc 21 GPIO_ACTIVE_LOW>;
		spi-index = <0>;/* voice header index */
	};
};

&vreg_sync {
		pinctrl-names = "default";
		pinctrl-0 = <&vreg_sync_pin_10>;
		vreg_sync_gpio = <10>;
};
&pincontroller {
        pinctrl-names = "default";
        pinctrl-0 = <&b_ntr_in_pin_19>;
};