#include "63158.dtsi"
#include "../bcm_voice.dtsi"
#include "963158REF3_leds.dtsi"

/ {
    memory_controller {
        memcfg = <(BP_DDR_SPEED_1067_14_14_14 | \
                   BP_DDR_TOTAL_SIZE_1024MB   | \
                   BP_DDR_DEVICE_WIDTH_16     | \
                   BP_DDR_TOTAL_WIDTH_32BIT   | \
                   BP_DDR_SSC_CONFIG_1)>;
    };

	buttons {
		compatible = "brcm,buttons";
		reset_button {
			ext_irq = <&bca_extintr 46 BCA_GPIO_ACTIVE_LOW (BCA_EXTINTR_TYPE_LOW_LEVEL | BCA_EXTINTR_TYPE_SENSE_EDGE)>;
			press {
				print = "Button Press -- Hold for 5s to do restore to default";
			};
			hold {
				rst_to_dflt = <5>;
			};
			release {
				reset = <0>;
			};	
		};
		ses_button {
			ext_irq = <&bca_extintr 41 BCA_GPIO_ACTIVE_LOW (BCA_EXTINTR_TYPE_LOW_LEVEL | BCA_EXTINTR_TYPE_SENSE_EDGE)>;
			release {
				ses_short_period = <0>;
				ses_long_period = <3>;
			};
		};
	};

	pmd: pmd {
		compatible = "brcm,pmd";
		pinctrl-names = "state_ewake";
		pinctrl-0 = <&a_wan_early_txen_pin_39>;
		ewake-gpio = <&gpioc 39 GPIO_ACTIVE_HIGH>;
		rstn-gpio = <&gpioc 5 GPIO_ACTIVE_LOW>;
		alarm = <&bca_extintr 40 GPIO_ACTIVE_HIGH (BCA_EXTINTR_TYPE_HIGH_LEVEL | BCA_EXTINTR_TYPE_SENSE_EDGE)>;
		apd-boost;
		i2c-bus = <&i2c0>;
	};
};

&i2c0 {
	pinctrl-names = "default";
	pinctrl-0 = <&b0_i2c_scl_0_pin_25 &b0_i2c_sda_0_pin_24>;
	status = "okay";
};

&usb_ctrl {
	pinctrl-names="default";
	pinctrl-0 = <&usb0a_pwr_pins &usb1a_pwr_pins>;
	status = "okay";
	xhci-enable;
};

&usb0_ehci {
	status = "okay";
};
&usb1_ehci {
	status = "okay";
};

&usb0_ohci {
	status = "okay";
};
&usb1_ohci {
	status = "okay";
};

&usb0_xhci {
	status = "okay";
};

&mdio_sf2 {
	/* PHYs directly connected to SF2 */
	gphy8:8 {
		status = "okay";
	};
	gphy9:9 {
		status = "okay";
	};
	gphya:a {
		status = "okay";
	};
	gphyb:b {
		status = "okay";
	};

	/* PHYs connected to crossbar */
	gphyc:c {
		status = "okay";
	};
	phy_serdes1:serdes1 {
		status = "okay";
	};

	/* Crossbar groups */
	xbar_grp2:2 {
		phy-handle = <&gphyc &phy_serdes1>;
		status = "okay";
	};
};

&switch_sf2 {
	ports {
		sf2_port0@0 {
			phy-handle = <&gphy8>;
			network-leds = <&led0 &led1 &led20>;
			status = "okay";
		};

		sf2_port1@1 {
			phy-handle = <&gphy9>;
			network-leds = <&led2 &led3 &led21>;
			status = "okay";
		};

		sf2_port2@2 {
			phy-handle = <&gphya>;
			network-leds = <&led4 &led5 &led22>;
			status = "okay";
		};

		sf2_port3@3 {
			phy-handle = <&gphyb>;
			network-leds = <&led6 &led7 &led23>;
			status = "okay";
		};
	};
};

&switch0 {
	ports {
		
		port5@5 {
			phy-handle = <&xbar_grp2>;
			/* xbar ext ep 0 serdes leds */
			network-leds-0 = <&led10 &led11 &led12 &led25>;
			/* xbar ext ep 1 sgphy leds */
			network-leds-1 = <&led8 &led9 &led24>;
			status = "okay";
		};

	};
};

&bcm_voice{
	sliclist = SLICSLAC_LIST_COMMON_NOFXO;
 };

&hsspi {
	voice0 {
		pinctrl-0 = <&spim_ss1_b_pin_112>;
		pinctrl-names = "default";
		compatible = "bcm-spi-voice";
		reg = <1>; /* chip select 1 */
		spi-max-frequency = <1024000>;
		reset-gpio = <&gpioc 4 GPIO_ACTIVE_LOW>;
		spi-index = <0>;/* voice header index */
	};
};