#include "63178.dtsi"

/ {
    memory_controller {
        memcfg = <(BP_DDR_SPEED_800_11_11_11 | \
                   BP_DDR_TOTAL_SIZE_1024MB  | \
                   BP_DDR_DEVICE_WIDTH_8     | \
                   BP_DDR_TOTAL_WIDTH_16BIT  | \
                   BP_DDR_63178_DEFAULT)>;
    };

	buttons {
		compatible = "brcm,buttons";
		reset_button {
			ext_irq = <&bca_extintr 0 BCA_GPIO_ACTIVE_LOW (BCA_EXTINTR_TYPE_LOW_LEVEL | BCA_EXTINTR_TYPE_SENSE_EDGE)>;
			press {
				print = "Button Press -- Hold for 5s to do restore to default";
			};
			hold {
				rst_to_dflt = <5>;
			};
			release {
				reset = <0>;
			};	
		};
		ses_button {
			ext_irq = <&bca_extintr 1 BCA_GPIO_ACTIVE_LOW (BCA_EXTINTR_TYPE_LOW_LEVEL | BCA_EXTINTR_TYPE_SENSE_EDGE)>;
			release {
				ses_short_period = <0>;
				ses_long_period = <3>;
			};
		};
	};
};

&switch0 {
        ports {
                port0@0 {
                        network-leds = <&led0 &led15>;
                        status = "okay";
                };

                port1@1 {
                        network-leds = <&led2 &led16>;
                        status = "okay";
                };

                port2@2 {
                        network-leds = <&led4 &led17>;
                        status = "okay";
                };

                port3@3 {
                        network-leds = <&led6 &led18>;
                        status = "okay";
                };

                port4@4 {
                        network-leds = <&led8 &led19>;
                        status = "okay";
                };
    };
};

&led_ctrl {
    pinctrl-names = "default";
    pinctrl-0 = <&b_ser_led_clk_pin_27 &b_ser_led_data_pin_26 &b_ser_led_mask_pin_28>;
    serial-shifters-installed = <2>;
    serial-data-polarity-high;
    led0: port_0-led_0-bit_0 {
        active_high;
        link = <(LED_SPEED_100|LED_SPEED_1G)>;
        status = "okay";
    };
    led2: port_1-led_0-bit_2 {
        active_high;
        link = <(LED_SPEED_100|LED_SPEED_1G)>;
        status = "okay";
    };
    led4: port_2-led_0-bit_4 {
        active_high;
        link = <(LED_SPEED_100|LED_SPEED_1G)>;
        status = "okay";
    };
    led6: port_3-led_0-bit_6 {
        active_high;
        link = <(LED_SPEED_100|LED_SPEED_1G)>;
        status = "okay";
    };
    led8: port_4-led_0-bit_8 {
        active_high;
        link = <(LED_SPEED_100|LED_SPEED_1G)>;
        status = "okay";
    };
    led15: port_0-led_3-bit_15 {
        active_high;
        activity = <LED_SPEED_GBE>;
        status = "okay";
    };
    led16: port_1-led_3-bit_16 {
        active_high;
        activity = <LED_SPEED_GBE>;
        status = "okay";
    };
    led17: port_2-led_3-bit_17 {
        active_high;
        activity = <LED_SPEED_GBE>;
        status = "okay";
    };
    led18: port_3-led_3-bit_18 {
        active_high;
        activity = <LED_SPEED_GBE>;
        status = "okay";
    };
    led19: port_4-led_3-bit_19 {
        active_high;
        activity = <LED_SPEED_GBE>;
        status = "okay";
    };
    led23: dsl_act_0-bit_23 {
        active_high;
        status = "okay";
    };
    led26: sw_led-bit_26 {
        active_high;
        status = "okay";
    };
    led27: sw_led-bit_27 {
        active_high;
        status = "okay";
    };
    led28: sw_led-bit_28 {
        active_high;
        status = "okay";
    };
    led29: sw_led-bit_29 {
        active_high;
        status = "okay";
    };
    led30: sw_led-bit_30 {
        active_high;
        status = "okay";
    };
};

&vreg_sync {
		pinctrl-0 = <&vreg_sync_pin_2>;
		pinctrl-names = "default";
};