#include "6813.dtsi"
#include "../bcm_voice.dtsi"

/ {
	memory_controller {
		memcfg = <(BP_DDR_TYPE_DDR4           | \
			BP_DDR_SPEED_1600_22_22_22    | \
			BP_DDR_TOTAL_SIZE_2048MB      | \
			BP_DDR_DEVICE_WIDTH_16        | \
			BP_DDR_TOTAL_WIDTH_32BIT      | \
			BP_DDR_6813_DEFAULT)>;
	};

	buttons: buttons {
		compatible = "brcm,buttons";
		reset_button {
			ext_irq = <&bca_extintr 51 GPIO_ACTIVE_LOW (BCA_EXTINTR_TYPE_LOW_LEVEL | BCA_EXTINTR_TYPE_SENSE_EDGE)>;
			press {
				print = "Button Press -- Hold for 5s to do restore to default";
			};
			hold {
				rst_to_dflt = <5>;
			};
			release {
				reset = <0>;
			};	
		};
		ses_button {
			ext_irq = <&bca_extintr 52 GPIO_ACTIVE_LOW (BCA_EXTINTR_TYPE_LOW_LEVEL | BCA_EXTINTR_TYPE_SENSE_EDGE)>;
			release {
				ses_short_period = <0>;
				ses_long_period = <3>;
			};
		};		
	};
	ubus@ff800000 {
		i2s: bcm63xx-i2s {
			pinctrl-0 = <&a_i2s_rx_sclk_pin_45 &a_i2s_rx_lrck_pin_46 &a_i2s_sdata_in_pin_47 &a_i2s_rx_mclk_pin_48 &a_i2s_sdata_out_pin_49 &a_i2s_tx_sclk_pin_50>;
			pinctrl-names = "default";
			compatible = "brcm,bcm63xx-i2s";
			reg = <0 0x2080 0 0x7f>;
			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&i2stxclk>,<&i2srxclk>,<&osc>;
			clock-names = "i2stxclk","i2srxclk","i2sosc";
		};
	};

};

&nand {
	write-protect = <1>;
};

#if defined(CONFIG_BCM_PCIE_HCD) || defined(CONFIG_BCM_PCIE_HCD_MODULE)
&pcie0 {
	status = "okay";
};
&pcie1 {
	status = "okay";
};
&pcie2 {
	status = "okay";
};
&pcie3 {
	status = "okay";
};
#endif //#if defined(CONFIG_BCM_PCIE_HCD) || defined(CONFIG_BCM_PCIE_HCD_MODULE)

&i2c0 {
	status = "okay";
};
&i2c1 {
	status = "okay";
};

&usb_ctrl {
	pinctrl-names = "default";
	pinctrl-0 = <&usb0_pwr_pins &usb1_pwr_pins>;
	status = "okay";
	xhci-enable;
};
&usb0_xhci {
	status = "okay";
};

&mdio {
	phy1:1 {
		status = "okay";
	};

	phy2:2 {
		status = "okay";
	};

	phy3:3 {
		status = "okay";
	};

	phy4:4 {
		status = "okay";
	};

	phy_rgmii: rgmii {
		status = "disabled";
	};

	phy_cascade0:9 {
		status = "okay";
	};

	phy_serdes0:6 {
		phy-handle = <&phy_cascade0>;
		status = "okay";
	};

	phy_serdes1:7 {
		status = "okay";
	};

	phy_serdes2:8 {
		status = "okay";
	};
};

&switch0 {
	ports {
		port0@0 {
			network-leds = <&led0 &led1>;
			status = "okay";
		};

		port1@1 {
			network-leds = <&led2 &led3>;
			status = "okay";
		};

		port2@2 {
			network-leds = <&led4 &led5>;
			status = "okay";
		};

		port3@3 {
			network-leds = <&led6 &led7>;
			status = "okay";
		};

		port5@5 {
			status = "okay";
		};

		port6@6 {
			status = "okay";
		};

		port7@7 {
			status = "okay";
		};
	};
};
&hsspi {
	status = "okay";
	voice0 {
		pinctrl-0 = <&hs_spim_ss_1_b_pin_20>;
		pinctrl-names = "default";
		compatible = "bcm-spi-voice";
		reg = <1>; /* chip select 1 */
		spi-max-frequency = <1024000>;
		reset-gpio = <&gpioc 13 GPIO_ACTIVE_LOW>;
		spi-index = <0>;/* voice header index */
	};	
};

&legacy_leds {
    wl-sess-led = <&led15>;
};

&led_ctrl {
    pinctrl-names = "default";
    pinctrl-0 = <&ser_led_clk_pin_17 &ser_led_data_pin_16 &ser_led_mask_pin_18>;
    serial-shifters-installed = <2>;
    serial-data-polarity-high;
    led0: serial-port_0-led_0 {
        active_high;
        crossbar-output = <0>;
        link = <(LED_SPEED_GBE)>;
        status = "okay";
    };
    led1: serial-port_0-led_1 {
        active_high;
        crossbar-output = <1>;
        activity = <(LED_SPEED_GBE)>;
        link = <(LED_SPEED_GBE)>;
        status = "okay";
    };
    led2: serial-port_1-led_0 {
        active_high;
        crossbar-output = <3>;
        link = <(LED_SPEED_GBE)>;
        status = "okay";
    };
    led3: serial-port_1-led_1 {
        active_high;
        crossbar-output = <4>;
        activity = <(LED_SPEED_GBE)>;
        link = <(LED_SPEED_GBE)>;
        status = "okay";
    };
    led4: serial-port_2-led_0 {
        active_high;
        crossbar-output = <6>;
        link = <(LED_SPEED_GBE)>;
        status = "okay";
    };
    led5: serial-port_2-led_1 {
        active_high;
        crossbar-output = <7>;
        activity = <(LED_SPEED_GBE)>;
        link = <(LED_SPEED_GBE)>;
        status = "okay";
    };
    led6: serial-port_3-led_0 {
        active_high;
        crossbar-output = <9>;
        link = <(LED_SPEED_GBE)>;
        status = "okay";
    };
    led7: serial-port_3-led_1 {
        active_high;
        crossbar-output = <10>;
        activity = <(LED_SPEED_GBE)>;
        link = <(LED_SPEED_GBE)>;
        status = "okay";
    };

    /*place holder for MPHY leds */
    led8: sw_serial_led_13 {
        active_high; 
        label = "mphy00";
        crossbar-output = <13>;
        status = "okay";
    };
    led9: sw_serial_led_14 {
        active_high; 
        label = "mphy01";
        crossbar-output = <14>;
        status = "okay";
    };
    led10: sw_serial_led_15 {
        active_high; 
        label = "mphy10";
        crossbar-output = <15>;
        status = "okay";
    };
    led11: sw_serial_led_16 {
        active_high; 
        label = "mphy11";
        crossbar-output = <16>;
        status = "okay";
    };
    led12: sw_serial_led_17 {
        active_high; 
        label = "mphy20";
        crossbar-output = <17>;
        status = "okay";
    };
    led13: sw_serial_led_18 {
        active_high; 
        label = "mphy21";
        crossbar-output = <18>;
        status = "okay";
    };
    led14: sw_serial_led_19 {
        active_high; 
        label = "INET";
        crossbar-output = <19>;
        status = "okay";
    };
    led15: sw_serial_led_20 {
        active_high; 
        label = "WPS";
        crossbar-output = <20>;
        status = "okay";
    };
};
&bcm_voice{
	sliclist = SLICSLAC_LIST_COMMON_NOFXO;
 };

&vreg_sync {
		pinctrl-0 = <&a_vreg_sync_pin_19>;
		pinctrl-names = "default";
};
&uart0 {
        pinctrl-names = "default";
        pinctrl-0 = <&uart0_sdin_pin_56 &uart0_sdout_pin_57 >;
        status = "okay";
};