#include "inc/68252.dtsi"

/ {
	memory_controller {
		memcfg = <(BP_DDR_SPEED_1067_14_14_14 | \
					BP_DDR_TOTAL_SIZE_512MB  | \
					BP_DDR_DEVICE_WIDTH_16    | \
					BP_DDR_TOTAL_WIDTH_16BIT  | \
					BP_DDR_SSC_CONFIG_1)>;
	};
};

/ {
      model = "968252CREF";

      buttons {
        compatible = "brcm,buttons";
        reset_button {
            ext_irq = <&bca_extintr 54 BCA_GPIO_ACTIVE_LOW (BCA_EXTINTR_TYPE_LOW_LEVEL | BCA_EXTINTR_TYPE_SENSE_EDGE)>;
            press {
                print = "Button Press -- Hold for 5s to do restore to default";
            };
            hold {
                rst_to_dflt = <5>;
            };
            release {
                reset = <0>;
            };
        };
        ses_button {
            ext_irq = <&bca_extintr 30 BCA_GPIO_ACTIVE_LOW (BCA_EXTINTR_TYPE_LOW_LEVEL | BCA_EXTINTR_TYPE_SENSE_EDGE)>;
            release {
                ses_short_period = <0>;
                ses_long_period = <3>;
            };
        };
    };

    xfp_sfp: xfp_sfp {
        compatible = "brcm,sfp";
        pinctrl-names = "default", "tx-sd";
        pinctrl-0 = <&pon_lbe_p_pin_100>;
        pinctrl-1 = <&pon_lbe_p_pin_100 &rogue_onu_in_pin_29>;
        i2c-bus = <&i2c0>;
        los-gpio = <&gpioc 12 GPIO_ACTIVE_HIGH>;
        mod-def0 = <&bca_extintr 13 GPIO_ACTIVE_LOW (BCA_EXTINTR_TYPE_BOTH_EDGE | BCA_EXTINTR_TYPE_SENSE_EDGE)>;
        tx-power-gpio = <&gpioc 28 GPIO_ACTIVE_HIGH>;
    };

    wan_serdes {
        compatible = "brcm,pon-drv";
        trx = <&xfp_sfp>;
        tx-polarity-invert;
        pon-led = <&led9>;
        alarm-led = <&led10>;
    };
};

&i2c0 {
    pinctrl-0 = <&i2c_scl_pin_77 &i2c_sda_pin_78>;
    pinctrl-names = "default";
    status = "okay";
};

&nand {
        status = "okay";
};
&wdt {
        status = "okay";
};
&uart0 {
        status = "okay";
};

&usb_ctrl {
    pinctrl-names = "default";
    pinctrl-0 = <&usb0_pwr_pins &usb1_pwr_pins>;
    status = "okay";
};
&usb0_ehci {
    status = "okay";
};
&usb0_ohci {
    status = "okay";
};
&usb1_ehci {
    status = "okay";
};
&usb1_ohci {
    status = "okay";
};

#if defined(CONFIG_BCM_PCIE_HCD) || defined(CONFIG_BCM_PCIE_HCD_MODULE)
&pcie0 {
    status = "okay";
};
#endif

&pincontroller {
    pinctrl-names = "default";
    pinctrl-0 = <&c0_femctrl_0_pin_84 &c0_femctrl_1_pin_85 &c0_femctrl_2_pin_86 &c0_femctrl_3_pin_87 \
                 &c0_femctrl_4_pin_88 &c0_femctrl_5_pin_89 &c1_femctrl_0_pin_90 &c1_femctrl_1_pin_91 \
                 &c1_femctrl_2_pin_92 &c1_femctrl_3_pin_93 &c1_femctrl_4_pin_94 &c1_femctrl_5_pin_95 >;
};

&mdio {
        phy1:1 {
                status = "okay";
        };

        phy2:2 {
                status = "okay";
        };

        phy3:3 {
                status = "okay";
        };

        phy4:4 {
                status = "okay";
        };
};

&switch0 {
        ports {
                port0@0 {
                        network-leds = <&led0 &led1>;
                        status = "okay";
                };

                port1@1 {
                        network-leds = <&led2 &led3>;
                        status = "okay";
                };

                port2@2 {
                        network-leds = <&led4 &led5>;
                        status = "okay";
                };

                port3@3 {
                        network-leds = <&led6 &led7>;
                        status = "okay";
                };
        };
};

&legacy_leds {
    usb-led = <&led11>;
    voip1-ok-led = <&led12>;
    wl-sess-led = <&led13>;
    wl0-led = <&led14>;
};

&led_ctrl {
    led0: parallel-port_0-led_0{
        active_low;
        pinctrl-0 = <&a_per_led_01_pin_1>;
        link = <LED_SPEED_GBE>;
        status = "okay";
    };

    led1: parallel-port_0-led_1{
        active_low;
        pinctrl-0 = <&a_per_led_02_pin_2>;
        activity = <LED_SPEED_GBE>;
        status = "okay";
    };

    led2: parallel-port_1-led_0{
        active_low;
        pinctrl-0 = <&a_per_led_14_pin_4>;
        link = <LED_SPEED_GBE>;
        status = "okay";
    };

    led3: parallel-port_1-led_1{
        active_low;
        pinctrl-0 = <&a_per_led_07_pin_8>;
        activity = <LED_SPEED_GBE>;
        status = "okay";
    };

    led4: parallel-port_2-led_0{
        active_low;
        pinctrl-0 = <&a_per_led_06_pin_7>;
        link = <LED_SPEED_GBE>;
        status = "okay";
    };

    led5: parallel-port_2-led_1{
        active_low;
        pinctrl-0 = <&a_per_led_11_pin_11>;
        activity = <LED_SPEED_GBE>;
        status = "okay";
    };

    led6: parallel-port_3-led_0{
        active_low;
        pinctrl-0 = <&a_per_led_09_pin_32>;
        link = <LED_SPEED_GBE>;
        status = "okay";
    };

    led7: parallel-port_3-led_1{
        active_low;
        pinctrl-0 = <&a_per_led_05_pin_15>;
        activity = <LED_SPEED_GBE>;
        status = "okay";
    };

    led8: sw_parallel_led_0{
        active_low;
        pinctrl-0 = <&a_per_led_00_pin_0>;
        label = "USB0";
        status = "okay";
    };

    led10: sw_parallel_led_3{
        active_low;
        label = "ALARM";
        pinctrl-0 = <&a_per_led_10_pin_10>;
        status = "okay";
    };

    led9: sw_parallel_led_4{
        active_low;
        pinctrl-0 = <&a_per_led_08_pin_9>;
        label = "WAN";
        status = "okay";
    };

    led11: sw_parallel_led_5{
        active_low;
        pinctrl-0 = <&a_per_led_16_pin_6>;
        label = "USB1";
        status = "okay";
    };

    led12: sw_parallel_led_1{
        active_low;
        pinctrl-0 = <&a_per_led_15_pin_5>;
        label = "VOIP1";
        status = "okay";
    };
    led13: sw_parallel_led_2{
        active_low;
        pinctrl-0 = <&b_per_led_03_pin_33>;
        label = "WPS";
        status = "okay";
    };
    led14: sw_parallel_led_6{
        active_low;
        pinctrl-0 = <&a_per_led_13_pin_3>;
        label = "WLAN0";
        status = "okay";
    };
};