#include "inc/68560.dtsi"
#include "../bcm_voice.dtsi"

/ {
    memory_controller {
        memcfg = <(BP_DDR_SPEED_800_11_11_11  | \
                   BP_DDR_TOTAL_SIZE_512MB    | \
                   BP_DDR_DEVICE_WIDTH_16     | \
                   BP_DDR_TOTAL_WIDTH_16BIT   | \
                   BP_DDR_SSC_CONFIG_1)>;
    };
};

/ {
    model = "968560CHGU";

    xfp_sfp: xfp_sfp {
        compatible = "brcm,sfp";
        pinctrl-names = "default", "tx-sd";
        pinctrl-0 = <&pon_lbe_p_pin_22>;
        pinctrl-1 = <&pon_lbe_p_pin_22 &a_rogue_onu_in_pin_10>;
        i2c-bus = <&i2c0>;
        los-gpio = <&gpioc 8 GPIO_ACTIVE_HIGH>;
        tx-power-gpio = <&gpioc 12 GPIO_ACTIVE_HIGH>;
    };

    smtc {
        compatible = "brcm,smtc";
        smtc-tx-dis-gpio = <&gpioc 21 GPIO_ACTIVE_HIGH>;
        i2c-bus = <&i2c0>;
    };

    wan_serdes {
            compatible = "brcm,pon-drv";
            trx = <&xfp_sfp>;
            pon-led = <&led20>;
            alarm-led = <&led0>;
    };

    buttons {
        compatible = "brcm,buttons";
        reset_button {
            ext_irq = <&bca_extintr 82 BCA_GPIO_ACTIVE_LOW (BCA_EXTINTR_TYPE_LOW_LEVEL | BCA_EXTINTR_TYPE_SENSE_EDGE)>;
            press {
                print = "Button Press -- Hold for 5s to do restore to default";
   	 };
            hold {
                rst_to_dflt = <5>;
            };
            release {
                reset = <0>;
            };	
        };
        ses_button {
            ext_irq = <&bca_extintr 83 BCA_GPIO_ACTIVE_LOW (BCA_EXTINTR_TYPE_LOW_LEVEL | BCA_EXTINTR_TYPE_SENSE_EDGE)>;
            release {
                ses_short_period = <0>;
                ses_long_period = <3>;
            };
        };
    };
};

&usb_ctrl {
    xhci-enable;
	status = "okay";
    pinctrl-names = "default";
    pinctrl-0 = <&usb0_pwr_pins &usb1_pwr_pins>;
};
&usb0_xhci {
    status = "okay";
};
&usb0_ehci {
	status = "okay";
};
&usb1_ehci {
	status = "okay";
};
&usb0_ohci {
	status = "okay";
};
&usb1_ohci {
	status = "okay";
};
&nand {
	status = "okay";
};

&uart0 {
	status = "okay";
};
&wdt {
	status = "okay";
};
&i2c0 {
    pinctrl-0 = <&i2c_scl_pin_20 &i2c_sda_pin_19>;
    pinctrl-names = "default";
    status = "okay";
};
&sdhci {
	status = "okay";
};
&hsspi {
	status = "okay";
};

&pcie0 {
	status = "okay";
};
&pcie1 {
	status = "okay";
};


&mdio {
        phy1:1 {
                status = "okay";
        };

        phy2:2 {
                status = "okay";
        };

        phy3:3 {
                status = "okay";
        };

        phy4:4 {
                status = "okay";
        };
};

&switch0 {
        ports {
                port0@0 {
                        network-leds = <&led3 &led4>;
                        status = "okay";
                };

                port1@1 {
                        network-leds = <&led5 &led6>;
                        status = "okay";
                };

                port2@2 {
                        network-leds = <&led7 &led8>;
                        status = "okay";
                };

                port3@3 {
                        network-leds = <&led9 &led10>;
                        status = "okay";
                };
        };
};

&led_ctrl {
    pinctrl-names = "default";
    pinctrl-0 = <&ser_led_clk_pin_27 &ser_led_data_pin_26 &ser_led_mask_pin_28>;
    serial-shifters-installed = <3>;

    led0: sw_led-bit_0 {
              active_low; 
              label = "OpticalLinkFail";
              status = "okay";
          };
    led1: sw_led-bit_1 {
              active_low; 
              label = "WAN";
              status = "okay";
          };
    led2: sw_led-bit_2 {
              active_low; 
              label = "WiFi";
              status = "okay";
          };
    led3: port_0-led_0-bit_3 {
              active_low;
              link = <LED_SPEED_GBE>;
              status = "okay";
          };
    led4: port_0-led_1-bit_4 {
              active_low;
              activity = <LED_SPEED_GBE>;
              status = "okay";
          };
    led5: port_1-led_0-bit_5 {
              active_low;
              link = <LED_SPEED_GBE>;
              status = "okay";
          };
    led6: port_1-led_1-bit_6 {
              active_low;
              activity = <LED_SPEED_GBE>;
              status = "okay";
          };
    led7: port_2-led_0-bit_7 {
              active_low;
              link = <LED_SPEED_GBE>;
              status = "okay";
          };
    led8: port_2-led_1-bit_8 {
              active_low;
              activity = <LED_SPEED_GBE>;
              status = "okay";
          };
    led9: port_3-led_0-bit_9 {
              active_low;
              link = <LED_SPEED_GBE>;
              status = "okay";
          };
    led10: port_3-led_1-bit_10 {
              active_low;
              activity = <LED_SPEED_GBE>;
              status = "okay";
          };
    led15: sw_led-bit_15 {
              active_low; 
              label = "USB_1";
              status = "okay";
          };
    led16: sw_led-bit_16 {
              active_low; 
              label = "VOIP_1";
              status = "okay";
          };
    led17: sw_led-bit_17 {
              active_low; 
              label = "VOIP_2";
              status = "okay";
          };
    led18: sw_led-bit_18 {
              active_low; 
              status = "okay";
          };
    led19: sw_led-bit_19 {
              active_low; 
              status = "okay";
          };
    led20: sw_led-bit_20 {
              active_low; 
              label = "PON";
              status = "okay";
          };
    led21: sw_led-bit_21 {
              active_low; 
              label = "USB_2";
              status = "okay";
          };
};

&legacy_leds {
    wan-data-led = <&led1>;
    voip1-ok-led = <&led16>;
    voip2-ok-led = <&led17>;
    usb-led = <&led15>;
    wl-sess-led = <&led2>;
};

&bcm_voice{
	sliclist = "NOSLIC", "LE9641_ZSI_BB";
};