#include "inc/68781.dtsi"
#include "../bcm_voice.dtsi"

/ {
    memory_controller {
        memcfg = <(BP_DDR_SPEED_800_11_11_11  | \
                   BP_DDR_TOTAL_SIZE_256MB    | \
                   BP_DDR_DEVICE_WIDTH_8      | \
                   BP_DDR_TOTAL_WIDTH_8BIT    | \
                   BP_DDR_PCB_2LAYER)>;
    };
};

/ {
    model = "968781REFS";

    wan_serdes {
            compatible = "brcm,pon-drv";
            trx = <&pmd>;
            rx-polarity-invert;
            tx-polarity-invert;
    };

    pmd: pmd {
            compatible = "brcm,pmd";
            pinctrl-names = "default", "state_ewake";
            pinctrl-0 = <&pon_lbe_p_pin_61>;
            pinctrl-1 = <&pon_lbe_p_pin_61 &wan_early_txen_pin_4>;
            ewake-gpio = <&gpioc 4 GPIO_ACTIVE_HIGH>;
            rstn-gpio = <&gpioc 11 GPIO_ACTIVE_LOW>;
            alarm = <&bca_extintr 13 GPIO_ACTIVE_HIGH (BCA_EXTINTR_TYPE_HIGH_LEVEL | BCA_EXTINTR_TYPE_SENSE_EDGE)>;
            apd-boost;
            i2c-bus = <&i2c0>;
    };

	 buttons {
        compatible = "brcm,buttons";
        reset_button {
            ext_irq = <&bca_extintr 53 BCA_GPIO_ACTIVE_LOW (BCA_EXTINTR_TYPE_LOW_LEVEL | BCA_EXTINTR_TYPE_SENSE_EDGE)>;
            press {
                print = "Button Press -- Hold for 5s to do restore to default";
   	 };
            hold {
                rst_to_dflt = <5>;
            };
            release {
                reset = <0>;
            };	
        };
    };
};

&mdio {
        phy1:1 {
                status = "okay";
        };

        phy2:2 {
                status = "okay";
        };

        phy3:3 {
                status = "okay";
        };

        phy4:4 {
                status = "okay";
        };
};

&switch0 {
        ports {
                port0@0 {
                        network-leds = <&led0>;
                        phy-mode = "mii";
                        status = "okay";
                };

                port1@1 {
                        network-leds = <&led1>;
                        phy-mode = "mii";
                        status = "okay";
                };

                port2@2 {
                        network-leds = <&led2>;
                        status = "okay";
                };

                port3@3 {
                        network-leds = <&led3>;
                        status = "okay";
                };
        };
};

&led_ctrl {
    led0: port_0-led_0-pin_50 {
              active_low;
              link = <LED_SPEED_FAE>;
              activity = <LED_SPEED_FAE>;
              status = "okay";
          };
    led1: port_1-led_0-pin_51 {
              active_low;
              link = <LED_SPEED_FAE>;
              activity = <LED_SPEED_FAE>;
              status = "okay";
          };
    led2: port_2-led_0-pin_47 {
              active_low;
              link = <LED_SPEED_GBE>;
              activity = <LED_SPEED_GBE>;
              status = "okay";
          };
    led3: port_3-led_0-pin_42 {
              active_low;
              link = <LED_SPEED_GBE>;
              activity = <LED_SPEED_GBE>;
              status = "okay";
          };
    led4: sw_led_6-pin_45 {
              active_low;
              status = "okay";
              label = "WLAN";
          };
};

&legacy_leds {
    wan-data-led = <&led4>;
};

&wdt {
	status = "okay";
};
&i2c0 {
    pinctrl-names = "default";
    pinctrl-0 = <&i2c_scl_pin_62 &i2c_sda_pin_63>;
	status = "okay";
};
&usb_ctrl {
    pinctrl-0 = <&usb0_pwr_pins>;
    pinctrl-names = "default";
	status = "okay";
};
&usb0_ehci {
	status = "okay";
};
&usb0_ohci {
	status = "okay";
};
&hsspi {
	status = "okay";
};
&spinand {
	status = "okay";
};

&bcm_voice{
	sliclist = "NOSLIC", "LE9641_ZSI_BB";
};