#include "inc/68782.dtsi"
#include "../bcm_voice.dtsi"

/ {
    model = "968782XSV";
};

/ {
    memory_controller {
        memcfg = <(BP_DDR_SPEED_800_11_11_11 | \
                   BP_DDR_TOTAL_SIZE_512MB   | \
                   BP_DDR_DEVICE_WIDTH_16    | \
                   BP_DDR_TOTAL_WIDTH_16BIT)>;
    };

    xfp_sfp: xfp_sfp {
        compatible = "brcm,sfp";
        pinctrl-names = "default", "tx-sd";
        pinctrl-0 = <&pon_lbe_p_pin_61>;
        pinctrl-1 = <&pon_lbe_p_pin_61 &rogue_onu_in_pin_13>;
        i2c-bus = <&i2c0>;
    };

    wan_serdes {
            compatible = "brcm,pon-drv";
            trx = <&xfp_sfp>;
    };
};

&rgmii {
        status = "okay";
};

&mdio {
        phy1:1 {
                status = "okay";
        };

        phy2:2 {
                status = "okay";
        };

        phy3:3 {
                status = "okay";
        };

        phy4:4 {
                status = "okay";
        };

        phy_rgmii: rgmii {
                reg = <7>;
                tx-delay;
                status = "okay";
        };
};

&switch0 {
        pinctrl-names = "default", "rgmii";
        pinctrl-0 = <&per_mdc_pin_52 &per_mdio_pin_53 &rgmii_pins>;
        pinctrl-1 = <&rgmii_pins>;

        ports {
                port0@0 {
                        network-leds = <&led8 &led9>;
                        status = "okay";
                };

                port1@1 {
                        network-leds = <&led10 &led11>;
                        status = "okay";
                };

                port2@2 {
                        network-leds = <&led12 &led13>;
                        status = "okay";
                };

                port3@3 {
                        network-leds = <&led14 &led15>;
                        status = "okay";
                };

                port4@4 {
                        mii-pinctrl-state = "rgmii";
                        status = "okay";
                };
        };
};

&led_ctrl {
    pinctrl-names = "default";
    pinctrl-0 = <&a_ser_led_clk_pin_8 &a_ser_led_data_pin_9 &a_ser_led_mask_pin_7>;
    serial-shifters-installed = <4>;

    led0: sw_led-bit_0 {
              active_low;
              status = "okay";
              label = "LED_0";
          };
    led1: sw_led-bit_1 {
              active_low;
              status = "okay";
              label = "LED_1";
          };
    led2: sw_led-bit_2 {
              active_low;
              status = "okay";
              label = "LED_2";
          };
    led3: sw_led-bit_3 {
              active_low;
              status = "okay";
              label = "LED_3";
          };
    led4: sw_led-bit_4 {
              active_low;
              status = "okay";
              label = "LED_4";
          };
    led5: sw_led-bit_5 {
              active_low;
              status = "okay";
              label = "LED_5";
          };
    led6: sw_led-bit_6 {
              active_low;
              status = "okay";
              label = "LED_6";
          };
    led7: sw_led-bit_7 {
              active_low;
              status = "okay";
              label = "LED_7";
          };
    led8: port_0-led_0-bit_8 {
              active_low;
              status = "okay";
              link = <LED_SPEED_GBE>;
          };
    led9: port_0-led_1-bit_9 {
              active_low;
              status = "okay";
              activity = <LED_SPEED_GBE>;
          };
    led10: port_1-led_0-bit_10 {
              active_low;
              status = "okay";
              link = <LED_SPEED_GBE>;
          };
    led11: port_1-led_1-bit_11 {
              active_low;
              status = "okay";
              activity = <LED_SPEED_GBE>;
          };
    led12: port_2-led_0-bit_12 {
              active_low;
              status = "okay";
              link = <LED_SPEED_GBE>;
          };
    led13: port_2-led_1-bit_13 {
              active_low;
              status = "okay";
              activity = <LED_SPEED_GBE>;
          };
    led14: port_3-led_0-bit_14 {
              active_low;
              status = "okay";
              link = <LED_SPEED_GBE>;
          };
    led15: port_3-led_1-bit_15 {
               active_low;
               status = "okay";
               activity = <LED_SPEED_GBE>;
          };
};

&legacy_leds {
    wan-data-led = <&led0>;
    voip1-ok-led = <&led1>;
    voip2-ok-led = <&led2>;
    usb-led = <&led3>;
    wl-sess-led = <&led4>;
};

&nand {
	status = "okay";
};
&hs_uart0 {
	status = "okay";
};
&wdt {
	status = "okay";
};
&i2c0 {
    pinctrl-names = "default";
    pinctrl-0 = <&i2c_scl_pin_62 &i2c_sda_pin_63>;
	status = "okay";
};
&usb_ctrl {
    pinctrl-names = "default";
    pinctrl-0 = <&usb0_pwr_pins &usb1_pwr_pins>;
	status = "okay";
};
&usb0_ehci {
	status = "okay";
};
&usb0_ohci {
	status = "okay";
};
&usb1_ehci {
	status = "okay";
};
&usb1_ohci {
	status = "okay";
};
&hsspi {
	status = "okay";
	pinctrl-0 = <&spim_group_pins>;
	pinctrl-names = "default";
	voice0 {
		pinctrl-0 = <&spim_ss0_b_pin_59>;
		pinctrl-names = "default";
		compatible = "bcm-spi-voice";
		reg = <0>; /* chip select 0 */
		spi-max-frequency = <1024000>;
		reset-gpio = <&gpioc 6 GPIO_ACTIVE_LOW>;
	};
};

&pcie0 {
	status = "okay";
};

&pincontroller {
    pinctrl-names = "default";
    pinctrl-0 = <&a_wl_fem_ctrl_2_pin_16 &wl_fem_ctrl_3_pin_17 &a_wl_fem_ctrl_8_pin_22 &wl_fem_ctrl_9_pin_23>;
};

&bcm_voice{
	sliclist = SLICSLAC_LIST_COMMON_NOFXO;
 };