/* * Analogix DP (Display Port) core interface driver. * * Copyright (C) 2012 Samsung Electronics Co., Ltd. * Author: Jingoo Han * * This program is free software; you can redistribute it and/or modify it * under the terms of the GNU General Public License as published by the * Free Software Foundation; either version 2 of the License, or (at your * option) any later version. */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "analogix_dp_core.h" #include "analogix_dp_reg.h" #define to_dp(nm) container_of(nm, struct analogix_dp_device, nm) static const bool verify_fast_training; struct bridge_init { struct i2c_client *client; struct device_node *node; }; static int analogix_dp_init_dp(struct analogix_dp_device *dp) { int ret; analogix_dp_reset(dp); analogix_dp_swreset(dp); analogix_dp_init_analog_param(dp); analogix_dp_init_interrupt(dp); /* SW defined function Normal operation */ analogix_dp_enable_sw_function(dp); analogix_dp_config_interrupt(dp); ret = analogix_dp_init_analog_func(dp); if (ret) return ret; analogix_dp_init_hpd(dp); analogix_dp_init_aux(dp); return 0; } static int analogix_dp_detect_hpd(struct analogix_dp_device *dp) { int timeout_loop = 0; while (timeout_loop < DP_TIMEOUT_LOOP_COUNT) { if (analogix_dp_get_plug_in_status(dp) == 0) return 0; timeout_loop++; usleep_range(1000, 1100); } /* * Some edp screen do not have hpd signal, so we can't just * return failed when hpd plug in detect failed, DT property * "force-hpd" would indicate whether driver need this. */ if (!dp->force_hpd) return -ETIMEDOUT; /* * The eDP TRM indicate that if HPD_STATUS(RO) is 0, AUX CH * will not work, so we need to give a force hpd action to * set HPD_STATUS manually. */ dev_dbg(dp->dev, "failed to get hpd plug status, try to force hpd\n"); analogix_dp_force_hpd(dp); if (analogix_dp_get_plug_in_status(dp) != 0) { dev_err(dp->dev, "failed to get hpd plug in status\n"); return -EINVAL; } dev_dbg(dp->dev, "success to get plug in status after force hpd\n"); return 0; } int analogix_dp_psr_enabled(struct analogix_dp_device *dp) { return dp->psr_enable; } EXPORT_SYMBOL_GPL(analogix_dp_psr_enabled); int analogix_dp_enable_psr(struct analogix_dp_device *dp) { struct edp_vsc_psr psr_vsc; if (!dp->psr_enable) return 0; /* Prepare VSC packet as per EDP 1.4 spec, Table 6.9 */ memset(&psr_vsc, 0, sizeof(psr_vsc)); psr_vsc.sdp_header.HB0 = 0; psr_vsc.sdp_header.HB1 = 0x7; psr_vsc.sdp_header.HB2 = 0x2; psr_vsc.sdp_header.HB3 = 0x8; psr_vsc.DB0 = 0; psr_vsc.DB1 = EDP_VSC_PSR_STATE_ACTIVE | EDP_VSC_PSR_CRC_VALUES_VALID; return analogix_dp_send_psr_spd(dp, &psr_vsc, true); } EXPORT_SYMBOL_GPL(analogix_dp_enable_psr); int analogix_dp_disable_psr(struct analogix_dp_device *dp) { struct edp_vsc_psr psr_vsc; int ret; if (!dp->psr_enable) return 0; /* Prepare VSC packet as per EDP 1.4 spec, Table 6.9 */ memset(&psr_vsc, 0, sizeof(psr_vsc)); psr_vsc.sdp_header.HB0 = 0; psr_vsc.sdp_header.HB1 = 0x7; psr_vsc.sdp_header.HB2 = 0x2; psr_vsc.sdp_header.HB3 = 0x8; psr_vsc.DB0 = 0; psr_vsc.DB1 = 0; ret = drm_dp_dpcd_writeb(&dp->aux, DP_SET_POWER, DP_SET_POWER_D0); if (ret != 1) { dev_err(dp->dev, "Failed to set DP Power0 %d\n", ret); return ret; } return analogix_dp_send_psr_spd(dp, &psr_vsc, false); } EXPORT_SYMBOL_GPL(analogix_dp_disable_psr); static int analogix_dp_detect_sink_psr(struct analogix_dp_device *dp) { unsigned char psr_version; int ret; ret = drm_dp_dpcd_readb(&dp->aux, DP_PSR_SUPPORT, &psr_version); if (ret != 1) { dev_err(dp->dev, "failed to get PSR version, disable it\n"); return ret; } dev_dbg(dp->dev, "Panel PSR version : %x\n", psr_version); dp->psr_enable = (psr_version & DP_PSR_IS_SUPPORTED) ? true : false; return 0; } static int analogix_dp_enable_sink_psr(struct analogix_dp_device *dp) { unsigned char psr_en; int ret; /* Disable psr function */ ret = drm_dp_dpcd_readb(&dp->aux, DP_PSR_EN_CFG, &psr_en); if (ret != 1) { dev_err(dp->dev, "failed to get psr config\n"); goto end; } psr_en &= ~DP_PSR_ENABLE; ret = drm_dp_dpcd_writeb(&dp->aux, DP_PSR_EN_CFG, psr_en); if (ret != 1) { dev_err(dp->dev, "failed to disable panel psr\n"); goto end; } /* Main-Link transmitter remains active during PSR active states */ psr_en = DP_PSR_MAIN_LINK_ACTIVE | DP_PSR_CRC_VERIFICATION; ret = drm_dp_dpcd_writeb(&dp->aux, DP_PSR_EN_CFG, psr_en); if (ret != 1) { dev_err(dp->dev, "failed to set panel psr\n"); goto end; } /* Enable psr function */ psr_en = DP_PSR_ENABLE | DP_PSR_MAIN_LINK_ACTIVE | DP_PSR_CRC_VERIFICATION; ret = drm_dp_dpcd_writeb(&dp->aux, DP_PSR_EN_CFG, psr_en); if (ret != 1) { dev_err(dp->dev, "failed to set panel psr\n"); goto end; } analogix_dp_enable_psr_crc(dp); return 0; end: dev_err(dp->dev, "enable psr fail, force to disable psr\n"); dp->psr_enable = false; return ret; } static int analogix_dp_enable_rx_to_enhanced_mode(struct analogix_dp_device *dp, bool enable) { u8 data; int ret; ret = drm_dp_dpcd_readb(&dp->aux, DP_LANE_COUNT_SET, &data); if (ret != 1) return ret; if (enable) ret = drm_dp_dpcd_writeb(&dp->aux, DP_LANE_COUNT_SET, DP_LANE_COUNT_ENHANCED_FRAME_EN | DPCD_LANE_COUNT_SET(data)); else ret = drm_dp_dpcd_writeb(&dp->aux, DP_LANE_COUNT_SET, DPCD_LANE_COUNT_SET(data)); return ret < 0 ? ret : 0; } static int analogix_dp_is_enhanced_mode_available(struct analogix_dp_device *dp, u8 *enhanced_mode_support) { u8 data; int ret; ret = drm_dp_dpcd_readb(&dp->aux, DP_MAX_LANE_COUNT, &data); if (ret != 1) { *enhanced_mode_support = 0; return ret; } *enhanced_mode_support = DPCD_ENHANCED_FRAME_CAP(data); return 0; } static int analogix_dp_set_enhanced_mode(struct analogix_dp_device *dp) { u8 data; int ret; ret = analogix_dp_is_enhanced_mode_available(dp, &data); if (ret < 0) return ret; ret = analogix_dp_enable_rx_to_enhanced_mode(dp, data); if (ret < 0) return ret; analogix_dp_enable_enhanced_mode(dp, data); return 0; } static int analogix_dp_training_pattern_dis(struct analogix_dp_device *dp) { int ret; analogix_dp_set_training_pattern(dp, DP_NONE); ret = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET, DP_TRAINING_PATTERN_DISABLE); return ret < 0 ? ret : 0; } static void analogix_dp_set_lane_lane_pre_emphasis(struct analogix_dp_device *dp, int pre_emphasis, int lane) { switch (lane) { case 0: analogix_dp_set_lane0_pre_emphasis(dp, pre_emphasis); break; case 1: analogix_dp_set_lane1_pre_emphasis(dp, pre_emphasis); break; case 2: analogix_dp_set_lane2_pre_emphasis(dp, pre_emphasis); break; case 3: analogix_dp_set_lane3_pre_emphasis(dp, pre_emphasis); break; } } static int analogix_dp_link_start(struct analogix_dp_device *dp) { u8 buf[4]; int lane, lane_count, pll_tries, retval; lane_count = dp->link_train.lane_count; dp->link_train.lt_state = CLOCK_RECOVERY; dp->link_train.eq_loop = 0; for (lane = 0; lane < lane_count; lane++) dp->link_train.cr_loop[lane] = 0; /* Set link rate and count as you want to establish*/ analogix_dp_set_link_bandwidth(dp, dp->link_train.link_rate); analogix_dp_set_lane_count(dp, dp->link_train.lane_count); /* Setup RX configuration */ buf[0] = dp->link_train.link_rate; buf[1] = dp->link_train.lane_count; retval = drm_dp_dpcd_write(&dp->aux, DP_LINK_BW_SET, buf, 2); if (retval < 0) return retval; /* set enhanced mode if available */ retval = analogix_dp_set_enhanced_mode(dp); if (retval < 0) { dev_err(dp->dev, "failed to set enhance mode\n"); return retval; } /* Set TX pre-emphasis to minimum */ for (lane = 0; lane < lane_count; lane++) analogix_dp_set_lane_lane_pre_emphasis(dp, PRE_EMPHASIS_LEVEL_0, lane); /* Wait for PLL lock */ pll_tries = 0; while (analogix_dp_get_pll_lock_status(dp) == PLL_UNLOCKED) { if (pll_tries == DP_TIMEOUT_LOOP_COUNT) { dev_err(dp->dev, "Wait for PLL lock timed out\n"); return -ETIMEDOUT; } pll_tries++; usleep_range(90, 120); } /* Set training pattern 1 */ analogix_dp_set_training_pattern(dp, TRAINING_PTN1); /* Set RX training pattern */ retval = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET, DP_LINK_SCRAMBLING_DISABLE | DP_TRAINING_PATTERN_1); if (retval < 0) return retval; for (lane = 0; lane < lane_count; lane++) buf[lane] = DP_TRAIN_PRE_EMPH_LEVEL_0 | DP_TRAIN_VOLTAGE_SWING_LEVEL_0; retval = drm_dp_dpcd_write(&dp->aux, DP_TRAINING_LANE0_SET, buf, lane_count); if (retval < 0) return retval; return 0; } static unsigned char analogix_dp_get_lane_status(u8 link_status[2], int lane) { int shift = (lane & 1) * 4; u8 link_value = link_status[lane >> 1]; return (link_value >> shift) & 0xf; } static int analogix_dp_clock_recovery_ok(u8 link_status[2], int lane_count) { int lane; u8 lane_status; for (lane = 0; lane < lane_count; lane++) { lane_status = analogix_dp_get_lane_status(link_status, lane); if ((lane_status & DP_LANE_CR_DONE) == 0) return -EINVAL; } return 0; } static int analogix_dp_channel_eq_ok(u8 link_status[2], u8 link_align, int lane_count) { int lane; u8 lane_status; if ((link_align & DP_INTERLANE_ALIGN_DONE) == 0) return -EINVAL; for (lane = 0; lane < lane_count; lane++) { lane_status = analogix_dp_get_lane_status(link_status, lane); lane_status &= DP_CHANNEL_EQ_BITS; if (lane_status != DP_CHANNEL_EQ_BITS) return -EINVAL; } return 0; } static unsigned char analogix_dp_get_adjust_request_voltage(u8 adjust_request[2], int lane) { int shift = (lane & 1) * 4; u8 link_value = adjust_request[lane >> 1]; return (link_value >> shift) & 0x3; } static unsigned char analogix_dp_get_adjust_request_pre_emphasis( u8 adjust_request[2], int lane) { int shift = (lane & 1) * 4; u8 link_value = adjust_request[lane >> 1]; return ((link_value >> shift) & 0xc) >> 2; } static void analogix_dp_set_lane_link_training(struct analogix_dp_device *dp, u8 training_lane_set, int lane) { switch (lane) { case 0: analogix_dp_set_lane0_link_training(dp, training_lane_set); break; case 1: analogix_dp_set_lane1_link_training(dp, training_lane_set); break; case 2: analogix_dp_set_lane2_link_training(dp, training_lane_set); break; case 3: analogix_dp_set_lane3_link_training(dp, training_lane_set); break; } } static unsigned int analogix_dp_get_lane_link_training(struct analogix_dp_device *dp, int lane) { u32 reg; switch (lane) { case 0: reg = analogix_dp_get_lane0_link_training(dp); break; case 1: reg = analogix_dp_get_lane1_link_training(dp); break; case 2: reg = analogix_dp_get_lane2_link_training(dp); break; case 3: reg = analogix_dp_get_lane3_link_training(dp); break; default: WARN_ON(1); return 0; } return reg; } static void analogix_dp_reduce_link_rate(struct analogix_dp_device *dp) { analogix_dp_training_pattern_dis(dp); analogix_dp_set_enhanced_mode(dp); dp->link_train.lt_state = FAILED; } static void analogix_dp_get_adjust_training_lane(struct analogix_dp_device *dp, u8 adjust_request[2]) { int lane, lane_count; u8 voltage_swing, pre_emphasis, training_lane; lane_count = dp->link_train.lane_count; for (lane = 0; lane < lane_count; lane++) { voltage_swing = analogix_dp_get_adjust_request_voltage( adjust_request, lane); pre_emphasis = analogix_dp_get_adjust_request_pre_emphasis( adjust_request, lane); training_lane = DPCD_VOLTAGE_SWING_SET(voltage_swing) | DPCD_PRE_EMPHASIS_SET(pre_emphasis); if (voltage_swing == VOLTAGE_LEVEL_3) training_lane |= DP_TRAIN_MAX_SWING_REACHED; if (pre_emphasis == PRE_EMPHASIS_LEVEL_3) training_lane |= DP_TRAIN_MAX_PRE_EMPHASIS_REACHED; dp->link_train.training_lane[lane] = training_lane; } } static int analogix_dp_process_clock_recovery(struct analogix_dp_device *dp) { int lane, lane_count, retval; u8 voltage_swing, pre_emphasis, training_lane; u8 link_status[2], adjust_request[2]; usleep_range(100, 101); lane_count = dp->link_train.lane_count; retval = drm_dp_dpcd_read(&dp->aux, DP_LANE0_1_STATUS, link_status, 2); if (retval < 0) return retval; retval = drm_dp_dpcd_read(&dp->aux, DP_ADJUST_REQUEST_LANE0_1, adjust_request, 2); if (retval < 0) return retval; if (analogix_dp_clock_recovery_ok(link_status, lane_count) == 0) { /* set training pattern 2 for EQ */ analogix_dp_set_training_pattern(dp, TRAINING_PTN2); retval = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET, DP_LINK_SCRAMBLING_DISABLE | DP_TRAINING_PATTERN_2); if (retval < 0) return retval; dev_info(dp->dev, "Link Training Clock Recovery success\n"); dp->link_train.lt_state = EQUALIZER_TRAINING; } else { for (lane = 0; lane < lane_count; lane++) { training_lane = analogix_dp_get_lane_link_training( dp, lane); voltage_swing = analogix_dp_get_adjust_request_voltage( adjust_request, lane); pre_emphasis = analogix_dp_get_adjust_request_pre_emphasis( adjust_request, lane); if (DPCD_VOLTAGE_SWING_GET(training_lane) == voltage_swing && DPCD_PRE_EMPHASIS_GET(training_lane) == pre_emphasis) dp->link_train.cr_loop[lane]++; if (dp->link_train.cr_loop[lane] == MAX_CR_LOOP || voltage_swing == VOLTAGE_LEVEL_3 || pre_emphasis == PRE_EMPHASIS_LEVEL_3) { dev_err(dp->dev, "CR Max reached (%d,%d,%d)\n", dp->link_train.cr_loop[lane], voltage_swing, pre_emphasis); analogix_dp_reduce_link_rate(dp); return -EIO; } } } analogix_dp_get_adjust_training_lane(dp, adjust_request); for (lane = 0; lane < lane_count; lane++) analogix_dp_set_lane_link_training(dp, dp->link_train.training_lane[lane], lane); retval = drm_dp_dpcd_write(&dp->aux, DP_TRAINING_LANE0_SET, dp->link_train.training_lane, lane_count); if (retval < 0) return retval; return 0; } static int analogix_dp_process_equalizer_training(struct analogix_dp_device *dp) { int lane, lane_count, retval; u32 reg; u8 link_align, link_status[2], adjust_request[2]; usleep_range(400, 401); lane_count = dp->link_train.lane_count; retval = drm_dp_dpcd_read(&dp->aux, DP_LANE0_1_STATUS, link_status, 2); if (retval < 0) return retval; if (analogix_dp_clock_recovery_ok(link_status, lane_count)) { analogix_dp_reduce_link_rate(dp); return -EIO; } retval = drm_dp_dpcd_read(&dp->aux, DP_ADJUST_REQUEST_LANE0_1, adjust_request, 2); if (retval < 0) return retval; retval = drm_dp_dpcd_readb(&dp->aux, DP_LANE_ALIGN_STATUS_UPDATED, &link_align); if (retval < 0) return retval; analogix_dp_get_adjust_training_lane(dp, adjust_request); if (!analogix_dp_channel_eq_ok(link_status, link_align, lane_count)) { /* traing pattern Set to Normal */ retval = analogix_dp_training_pattern_dis(dp); if (retval < 0) return retval; dev_info(dp->dev, "Link Training success!\n"); analogix_dp_get_link_bandwidth(dp, ®); dp->link_train.link_rate = reg; dev_dbg(dp->dev, "final bandwidth = %.2x\n", dp->link_train.link_rate); analogix_dp_get_lane_count(dp, ®); dp->link_train.lane_count = reg; dev_dbg(dp->dev, "final lane count = %.2x\n", dp->link_train.lane_count); dp->link_train.lt_state = FINISHED; return 0; } /* not all locked */ dp->link_train.eq_loop++; if (dp->link_train.eq_loop > MAX_EQ_LOOP) { dev_err(dp->dev, "EQ Max loop\n"); analogix_dp_reduce_link_rate(dp); return -EIO; } for (lane = 0; lane < lane_count; lane++) analogix_dp_set_lane_link_training(dp, dp->link_train.training_lane[lane], lane); retval = drm_dp_dpcd_write(&dp->aux, DP_TRAINING_LANE0_SET, dp->link_train.training_lane, lane_count); if (retval < 0) return retval; return 0; } static void analogix_dp_get_max_rx_bandwidth(struct analogix_dp_device *dp, u8 *bandwidth) { u8 data; /* * For DP rev.1.1, Maximum link rate of Main Link lanes * 0x06 = 1.62 Gbps, 0x0a = 2.7 Gbps * For DP rev.1.2, Maximum link rate of Main Link lanes * 0x06 = 1.62 Gbps, 0x0a = 2.7 Gbps, 0x14 = 5.4Gbps */ drm_dp_dpcd_readb(&dp->aux, DP_MAX_LINK_RATE, &data); *bandwidth = data; } static void analogix_dp_get_max_rx_lane_count(struct analogix_dp_device *dp, u8 *lane_count) { u8 data; /* * For DP rev.1.1, Maximum number of Main Link lanes * 0x01 = 1 lane, 0x02 = 2 lanes, 0x04 = 4 lanes */ drm_dp_dpcd_readb(&dp->aux, DP_MAX_LANE_COUNT, &data); *lane_count = DPCD_MAX_LANE_COUNT(data); } static int analogix_dp_full_link_train(struct analogix_dp_device *dp, u32 max_lanes, u32 max_rate) { int retval = 0; bool training_finished = false; /* * MACRO_RST must be applied after the PLL_LOCK to avoid * the DP inter pair skew issue for at least 10 us */ analogix_dp_reset_macro(dp); /* Initialize by reading RX's DPCD */ analogix_dp_get_max_rx_bandwidth(dp, &dp->link_train.link_rate); analogix_dp_get_max_rx_lane_count(dp, &dp->link_train.lane_count); if ((dp->link_train.link_rate != DP_LINK_BW_1_62) && (dp->link_train.link_rate != DP_LINK_BW_2_7) && (dp->link_train.link_rate != DP_LINK_BW_5_4)) { dev_err(dp->dev, "Rx Max Link Rate is abnormal :%x !\n", dp->link_train.link_rate); dp->link_train.link_rate = DP_LINK_BW_1_62; } if (dp->link_train.lane_count == 0) { dev_err(dp->dev, "Rx Max Lane count is abnormal :%x !\n", dp->link_train.lane_count); dp->link_train.lane_count = (u8)LANE_COUNT1; } /* Setup TX lane count & rate */ if (dp->link_train.lane_count > max_lanes) dp->link_train.lane_count = max_lanes; if (dp->link_train.link_rate > max_rate) dp->link_train.link_rate = max_rate; /* All DP analog module power up */ analogix_dp_set_analog_power_down(dp, POWER_ALL, 0); dp->link_train.lt_state = START; /* Process here */ while (!retval && !training_finished) { switch (dp->link_train.lt_state) { case START: retval = analogix_dp_link_start(dp); if (retval) dev_err(dp->dev, "LT link start failed!\n"); break; case CLOCK_RECOVERY: retval = analogix_dp_process_clock_recovery(dp); if (retval) dev_err(dp->dev, "LT CR failed!\n"); break; case EQUALIZER_TRAINING: retval = analogix_dp_process_equalizer_training(dp); if (retval) dev_err(dp->dev, "LT EQ failed!\n"); break; case FINISHED: training_finished = 1; break; case FAILED: return -EREMOTEIO; } } if (retval) dev_err(dp->dev, "eDP link training failed (%d)\n", retval); return retval; } static int analogix_dp_fast_link_train(struct analogix_dp_device *dp) { int i, ret; u8 link_align, link_status[2]; enum pll_status status; analogix_dp_reset_macro(dp); analogix_dp_set_link_bandwidth(dp, dp->link_train.link_rate); analogix_dp_set_lane_count(dp, dp->link_train.lane_count); for (i = 0; i < dp->link_train.lane_count; i++) { analogix_dp_set_lane_link_training(dp, dp->link_train.training_lane[i], i); } ret = readx_poll_timeout(analogix_dp_get_pll_lock_status, dp, status, status != PLL_UNLOCKED, 120, 120 * DP_TIMEOUT_LOOP_COUNT); if (ret) { DRM_DEV_ERROR(dp->dev, "Wait for pll lock failed %d\n", ret); return ret; } /* source Set training pattern 1 */ analogix_dp_set_training_pattern(dp, TRAINING_PTN1); /* From DP spec, pattern must be on-screen for a minimum 500us */ usleep_range(500, 600); analogix_dp_set_training_pattern(dp, TRAINING_PTN2); /* From DP spec, pattern must be on-screen for a minimum 500us */ usleep_range(500, 600); /* TODO: enhanced_mode?*/ analogix_dp_set_training_pattern(dp, DP_NONE); /* * Useful for debugging issues with fast link training, disable for more * speed */ if (verify_fast_training) { ret = drm_dp_dpcd_readb(&dp->aux, DP_LANE_ALIGN_STATUS_UPDATED, &link_align); if (ret < 0) { DRM_DEV_ERROR(dp->dev, "Read align status failed %d\n", ret); return ret; } ret = drm_dp_dpcd_read(&dp->aux, DP_LANE0_1_STATUS, link_status, 2); if (ret < 0) { DRM_DEV_ERROR(dp->dev, "Read link status failed %d\n", ret); return ret; } if (analogix_dp_clock_recovery_ok(link_status, dp->link_train.lane_count)) { DRM_DEV_ERROR(dp->dev, "Clock recovery failed\n"); analogix_dp_reduce_link_rate(dp); return -EIO; } if (analogix_dp_channel_eq_ok(link_status, link_align, dp->link_train.lane_count)) { DRM_DEV_ERROR(dp->dev, "Channel EQ failed\n"); analogix_dp_reduce_link_rate(dp); return -EIO; } } return 0; } static int analogix_dp_train_link(struct analogix_dp_device *dp) { if (dp->fast_train_enable) return analogix_dp_fast_link_train(dp); return analogix_dp_full_link_train(dp, dp->video_info.max_lane_count, dp->video_info.max_link_rate); } static int analogix_dp_config_video(struct analogix_dp_device *dp) { int timeout_loop = 0; int done_count = 0; analogix_dp_config_video_slave_mode(dp); analogix_dp_set_video_color_format(dp); if (analogix_dp_get_pll_lock_status(dp) == PLL_UNLOCKED) { dev_err(dp->dev, "PLL is not locked yet.\n"); return -EINVAL; } for (;;) { timeout_loop++; if (analogix_dp_is_slave_video_stream_clock_on(dp) == 0) break; if (timeout_loop > DP_TIMEOUT_LOOP_COUNT) { dev_err(dp->dev, "Timeout of slave video streamclk ok\n"); return -ETIMEDOUT; } usleep_range(1000, 1001); } /* Set to use the register calculated M/N video */ analogix_dp_set_video_cr_mn(dp, CALCULATED_M, 0, 0); /* For video bist, Video timing must be generated by register */ analogix_dp_set_video_timing_mode(dp, VIDEO_TIMING_FROM_CAPTURE); /* Disable video mute */ analogix_dp_enable_video_mute(dp, 0); /* Configure video slave mode */ analogix_dp_enable_video_master(dp, 0); /* Enable video */ analogix_dp_start_video(dp); timeout_loop = 0; for (;;) { timeout_loop++; if (analogix_dp_is_video_stream_on(dp) == 0) { done_count++; if (done_count > 10) break; } else if (done_count) { done_count = 0; } if (timeout_loop > DP_TIMEOUT_LOOP_COUNT) { dev_warn(dp->dev, "Ignoring timeout of video streamclk ok\n"); break; } usleep_range(1000, 1001); } return 0; } static int analogix_dp_enable_scramble(struct analogix_dp_device *dp, bool enable) { u8 data; int ret; if (enable) { analogix_dp_enable_scrambling(dp); ret = drm_dp_dpcd_readb(&dp->aux, DP_TRAINING_PATTERN_SET, &data); if (ret != 1) return ret; ret = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET, (u8)(data & ~DP_LINK_SCRAMBLING_DISABLE)); } else { analogix_dp_disable_scrambling(dp); ret = drm_dp_dpcd_readb(&dp->aux, DP_TRAINING_PATTERN_SET, &data); if (ret != 1) return ret; ret = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET, (u8)(data | DP_LINK_SCRAMBLING_DISABLE)); } return ret < 0 ? ret : 0; } static irqreturn_t analogix_dp_hardirq(int irq, void *arg) { struct analogix_dp_device *dp = arg; irqreturn_t ret = IRQ_NONE; enum dp_irq_type irq_type; irq_type = analogix_dp_get_irq_type(dp); if (irq_type != DP_IRQ_TYPE_UNKNOWN) { analogix_dp_mute_hpd_interrupt(dp); ret = IRQ_WAKE_THREAD; } return ret; } static irqreturn_t analogix_dp_irq_thread(int irq, void *arg) { struct analogix_dp_device *dp = arg; enum dp_irq_type irq_type; irq_type = analogix_dp_get_irq_type(dp); if (irq_type & DP_IRQ_TYPE_HP_CABLE_IN || irq_type & DP_IRQ_TYPE_HP_CABLE_OUT) { dev_dbg(dp->dev, "Detected cable status changed!\n"); if (dp->drm_dev) drm_helper_hpd_irq_event(dp->drm_dev); } if (irq_type != DP_IRQ_TYPE_UNKNOWN) { analogix_dp_clear_hotplug_interrupts(dp); analogix_dp_unmute_hpd_interrupt(dp); } return IRQ_HANDLED; } static int analogix_dp_fast_link_train_detection(struct analogix_dp_device *dp) { int ret; u8 spread; ret = drm_dp_dpcd_readb(&dp->aux, DP_MAX_DOWNSPREAD, &spread); if (ret != 1) { dev_err(dp->dev, "failed to read downspread %d\n", ret); return ret; } dp->fast_train_enable = !!(spread & DP_NO_AUX_HANDSHAKE_LINK_TRAINING); dev_dbg(dp->dev, "fast link training %s\n", dp->fast_train_enable ? "supported" : "unsupported"); return 0; } static int analogix_dp_commit(struct analogix_dp_device *dp) { int ret; /* Keep the panel disabled while we configure video */ if (dp->plat_data->panel) { if (drm_panel_disable(dp->plat_data->panel)) DRM_ERROR("failed to disable the panel\n"); } ret = analogix_dp_train_link(dp); if (ret) { dev_err(dp->dev, "unable to do link train, ret=%d\n", ret); return ret; } ret = analogix_dp_enable_scramble(dp, 1); if (ret < 0) { dev_err(dp->dev, "can not enable scramble\n"); return ret; } analogix_dp_init_video(dp); ret = analogix_dp_config_video(dp); if (ret) { dev_err(dp->dev, "unable to config video\n"); return ret; } /* Safe to enable the panel now */ if (dp->plat_data->panel) { ret = drm_panel_enable(dp->plat_data->panel); if (ret) { DRM_ERROR("failed to enable the panel\n"); return ret; } } ret = analogix_dp_detect_sink_psr(dp); if (ret) return ret; /* Check whether panel supports fast training */ ret = analogix_dp_fast_link_train_detection(dp); if (ret) dp->psr_enable = false; if (dp->psr_enable) { ret = analogix_dp_enable_sink_psr(dp); if (ret) return ret; } return ret; } /* * This function is a bit of a catch-all for panel preparation, hopefully * simplifying the logic of functions that need to prepare/unprepare the panel * below. * * If @prepare is true, this function will prepare the panel. Conversely, if it * is false, the panel will be unprepared. * * If @is_modeset_prepare is true, the function will disregard the current state * of the panel and either prepare/unprepare the panel based on @prepare. Once * it finishes, it will update dp->panel_is_modeset to reflect the current state * of the panel. */ static int analogix_dp_prepare_panel(struct analogix_dp_device *dp, bool prepare, bool is_modeset_prepare) { int ret = 0; if (!dp->plat_data->panel) return 0; mutex_lock(&dp->panel_lock); /* * Exit early if this is a temporary prepare/unprepare and we're already * modeset (since we neither want to prepare twice or unprepare early). */ if (dp->panel_is_modeset && !is_modeset_prepare) goto out; if (prepare) ret = drm_panel_prepare(dp->plat_data->panel); else ret = drm_panel_unprepare(dp->plat_data->panel); if (ret) goto out; if (is_modeset_prepare) dp->panel_is_modeset = prepare; out: mutex_unlock(&dp->panel_lock); return ret; } static int analogix_dp_get_modes(struct drm_connector *connector) { struct analogix_dp_device *dp = to_dp(connector); struct edid *edid; int ret, num_modes = 0; if (dp->plat_data->panel) { num_modes += drm_panel_get_modes(dp->plat_data->panel); } else { ret = analogix_dp_prepare_panel(dp, true, false); if (ret) { DRM_ERROR("Failed to prepare panel (%d)\n", ret); return 0; } pm_runtime_get_sync(dp->dev); edid = drm_get_edid(connector, &dp->aux.ddc); pm_runtime_put(dp->dev); if (edid) { drm_connector_update_edid_property(&dp->connector, edid); num_modes += drm_add_edid_modes(&dp->connector, edid); kfree(edid); } ret = analogix_dp_prepare_panel(dp, false, false); if (ret) DRM_ERROR("Failed to unprepare panel (%d)\n", ret); } if (dp->plat_data->get_modes) num_modes += dp->plat_data->get_modes(dp->plat_data, connector); return num_modes; } static struct drm_encoder * analogix_dp_best_encoder(struct drm_connector *connector) { struct analogix_dp_device *dp = to_dp(connector); return dp->encoder; } static const struct drm_connector_helper_funcs analogix_dp_connector_helper_funcs = { .get_modes = analogix_dp_get_modes, .best_encoder = analogix_dp_best_encoder, }; static enum drm_connector_status analogix_dp_detect(struct drm_connector *connector, bool force) { struct analogix_dp_device *dp = to_dp(connector); enum drm_connector_status status = connector_status_disconnected; int ret; if (dp->plat_data->panel) return connector_status_connected; ret = analogix_dp_prepare_panel(dp, true, false); if (ret) { DRM_ERROR("Failed to prepare panel (%d)\n", ret); return connector_status_disconnected; } if (!analogix_dp_detect_hpd(dp)) status = connector_status_connected; ret = analogix_dp_prepare_panel(dp, false, false); if (ret) DRM_ERROR("Failed to unprepare panel (%d)\n", ret); return status; } static const struct drm_connector_funcs analogix_dp_connector_funcs = { .fill_modes = drm_helper_probe_single_connector_modes, .detect = analogix_dp_detect, .destroy = drm_connector_cleanup, .reset = drm_atomic_helper_connector_reset, .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, }; static int analogix_dp_bridge_attach(struct drm_bridge *bridge) { struct analogix_dp_device *dp = bridge->driver_private; struct drm_encoder *encoder = dp->encoder; struct drm_connector *connector = NULL; int ret = 0; if (!bridge->encoder) { DRM_ERROR("Parent encoder object not found"); return -ENODEV; } if (!dp->plat_data->skip_connector) { connector = &dp->connector; connector->polled = DRM_CONNECTOR_POLL_HPD; ret = drm_connector_init(dp->drm_dev, connector, &analogix_dp_connector_funcs, DRM_MODE_CONNECTOR_eDP); if (ret) { DRM_ERROR("Failed to initialize connector with drm\n"); return ret; } drm_connector_helper_add(connector, &analogix_dp_connector_helper_funcs); drm_connector_attach_encoder(connector, encoder); } /* * NOTE: the connector registration is implemented in analogix * platform driver, that to say connector would be exist after * plat_data->attch return, that's why we record the connector * point after plat attached. */ if (dp->plat_data->attach) { ret = dp->plat_data->attach(dp->plat_data, bridge, connector); if (ret) { DRM_ERROR("Failed at platform attch func\n"); return ret; } } if (dp->plat_data->panel) { ret = drm_panel_attach(dp->plat_data->panel, &dp->connector); if (ret) { DRM_ERROR("Failed to attach panel\n"); return ret; } } return 0; } static void analogix_dp_bridge_pre_enable(struct drm_bridge *bridge) { struct analogix_dp_device *dp = bridge->driver_private; int ret; ret = analogix_dp_prepare_panel(dp, true, true); if (ret) DRM_ERROR("failed to setup the panel ret = %d\n", ret); } static int analogix_dp_set_bridge(struct analogix_dp_device *dp) { int ret; pm_runtime_get_sync(dp->dev); ret = clk_prepare_enable(dp->clock); if (ret < 0) { DRM_ERROR("Failed to prepare_enable the clock clk [%d]\n", ret); goto out_dp_clk_pre; } if (dp->plat_data->power_on_start) dp->plat_data->power_on_start(dp->plat_data); phy_power_on(dp->phy); ret = analogix_dp_init_dp(dp); if (ret) goto out_dp_init; /* * According to DP spec v1.3 chap 3.5.1.2 Link Training, * We should first make sure the HPD signal is asserted high by device * when we want to establish a link with it. */ ret = analogix_dp_detect_hpd(dp); if (ret) { DRM_ERROR("failed to get hpd single ret = %d\n", ret); goto out_dp_init; } ret = analogix_dp_commit(dp); if (ret) { DRM_ERROR("dp commit error, ret = %d\n", ret); goto out_dp_init; } if (dp->plat_data->power_on_end) dp->plat_data->power_on_end(dp->plat_data); enable_irq(dp->irq); return 0; out_dp_init: phy_power_off(dp->phy); if (dp->plat_data->power_off) dp->plat_data->power_off(dp->plat_data); clk_disable_unprepare(dp->clock); out_dp_clk_pre: pm_runtime_put_sync(dp->dev); return ret; } static void analogix_dp_bridge_enable(struct drm_bridge *bridge) { struct analogix_dp_device *dp = bridge->driver_private; int timeout_loop = 0; if (dp->dpms_mode == DRM_MODE_DPMS_ON) return; while (timeout_loop < MAX_PLL_LOCK_LOOP) { if (analogix_dp_set_bridge(dp) == 0) { dp->dpms_mode = DRM_MODE_DPMS_ON; return; } dev_err(dp->dev, "failed to set bridge, retry: %d\n", timeout_loop); timeout_loop++; usleep_range(10, 11); } dev_err(dp->dev, "too many times retry set bridge, give it up\n"); } static void analogix_dp_bridge_disable(struct drm_bridge *bridge) { struct analogix_dp_device *dp = bridge->driver_private; int ret; if (dp->dpms_mode != DRM_MODE_DPMS_ON) return; if (dp->plat_data->panel) { if (drm_panel_disable(dp->plat_data->panel)) { DRM_ERROR("failed to disable the panel\n"); return; } } disable_irq(dp->irq); if (dp->plat_data->power_off) dp->plat_data->power_off(dp->plat_data); analogix_dp_set_analog_power_down(dp, POWER_ALL, 1); phy_power_off(dp->phy); clk_disable_unprepare(dp->clock); pm_runtime_put_sync(dp->dev); ret = analogix_dp_prepare_panel(dp, false, true); if (ret) DRM_ERROR("failed to setup the panel ret = %d\n", ret); dp->psr_enable = false; dp->fast_train_enable = false; dp->dpms_mode = DRM_MODE_DPMS_OFF; } static void analogix_dp_bridge_mode_set(struct drm_bridge *bridge, struct drm_display_mode *orig_mode, struct drm_display_mode *mode) { struct analogix_dp_device *dp = bridge->driver_private; struct drm_display_info *display_info = &dp->connector.display_info; struct video_info *video = &dp->video_info; struct device_node *dp_node = dp->dev->of_node; int vic; /* Input video interlaces & hsync pol & vsync pol */ video->interlaced = !!(mode->flags & DRM_MODE_FLAG_INTERLACE); video->v_sync_polarity = !!(mode->flags & DRM_MODE_FLAG_NVSYNC); video->h_sync_polarity = !!(mode->flags & DRM_MODE_FLAG_NHSYNC); /* Input video dynamic_range & colorimetry */ vic = drm_match_cea_mode(mode); if ((vic == 6) || (vic == 7) || (vic == 21) || (vic == 22) || (vic == 2) || (vic == 3) || (vic == 17) || (vic == 18)) { video->dynamic_range = CEA; video->ycbcr_coeff = COLOR_YCBCR601; } else if (vic) { video->dynamic_range = CEA; video->ycbcr_coeff = COLOR_YCBCR709; } else { video->dynamic_range = VESA; video->ycbcr_coeff = COLOR_YCBCR709; } /* Input vide bpc and color_formats */ switch (display_info->bpc) { case 12: video->color_depth = COLOR_12; break; case 10: video->color_depth = COLOR_10; break; case 8: video->color_depth = COLOR_8; break; case 6: video->color_depth = COLOR_6; break; default: video->color_depth = COLOR_8; break; } if (display_info->color_formats & DRM_COLOR_FORMAT_YCRCB444) video->color_space = COLOR_YCBCR444; else if (display_info->color_formats & DRM_COLOR_FORMAT_YCRCB422) video->color_space = COLOR_YCBCR422; else if (display_info->color_formats & DRM_COLOR_FORMAT_RGB444) video->color_space = COLOR_RGB; else video->color_space = COLOR_RGB; /* * NOTE: those property parsing code is used for providing backward * compatibility for samsung platform. * Due to we used the "of_property_read_u32" interfaces, when this * property isn't present, the "video_info" can keep the original * values and wouldn't be modified. */ of_property_read_u32(dp_node, "samsung,color-space", &video->color_space); of_property_read_u32(dp_node, "samsung,dynamic-range", &video->dynamic_range); of_property_read_u32(dp_node, "samsung,ycbcr-coeff", &video->ycbcr_coeff); of_property_read_u32(dp_node, "samsung,color-depth", &video->color_depth); if (of_property_read_bool(dp_node, "hsync-active-high")) video->h_sync_polarity = true; if (of_property_read_bool(dp_node, "vsync-active-high")) video->v_sync_polarity = true; if (of_property_read_bool(dp_node, "interlaced")) video->interlaced = true; } static void analogix_dp_bridge_nop(struct drm_bridge *bridge) { /* do nothing */ } static const struct drm_bridge_funcs analogix_dp_bridge_funcs = { .pre_enable = analogix_dp_bridge_pre_enable, .enable = analogix_dp_bridge_enable, .disable = analogix_dp_bridge_disable, .post_disable = analogix_dp_bridge_nop, .mode_set = analogix_dp_bridge_mode_set, .attach = analogix_dp_bridge_attach, }; static int analogix_dp_create_bridge(struct drm_device *drm_dev, struct analogix_dp_device *dp) { struct drm_bridge *bridge; int ret; bridge = devm_kzalloc(drm_dev->dev, sizeof(*bridge), GFP_KERNEL); if (!bridge) { DRM_ERROR("failed to allocate for drm bridge\n"); return -ENOMEM; } dp->bridge = bridge; bridge->driver_private = dp; bridge->funcs = &analogix_dp_bridge_funcs; ret = drm_bridge_attach(dp->encoder, bridge, NULL); if (ret) { DRM_ERROR("failed to attach drm bridge\n"); return -EINVAL; } return 0; } static int analogix_dp_dt_parse_pdata(struct analogix_dp_device *dp) { struct device_node *dp_node = dp->dev->of_node; struct video_info *video_info = &dp->video_info; switch (dp->plat_data->dev_type) { case RK3288_DP: case RK3399_EDP: /* * Like Rk3288 DisplayPort TRM indicate that "Main link * containing 4 physical lanes of 2.7/1.62 Gbps/lane". */ video_info->max_link_rate = 0x0A; video_info->max_lane_count = 0x04; break; case EXYNOS_DP: /* * NOTE: those property parseing code is used for * providing backward compatibility for samsung platform. */ of_property_read_u32(dp_node, "samsung,link-rate", &video_info->max_link_rate); of_property_read_u32(dp_node, "samsung,lane-count", &video_info->max_lane_count); break; } return 0; } static ssize_t analogix_dpaux_transfer(struct drm_dp_aux *aux, struct drm_dp_aux_msg *msg) { struct analogix_dp_device *dp = to_dp(aux); return analogix_dp_transfer(dp, msg); } struct analogix_dp_device * analogix_dp_bind(struct device *dev, struct drm_device *drm_dev, struct analogix_dp_plat_data *plat_data) { struct platform_device *pdev = to_platform_device(dev); struct analogix_dp_device *dp; struct resource *res; unsigned int irq_flags; int ret; if (!plat_data) { dev_err(dev, "Invalided input plat_data\n"); return ERR_PTR(-EINVAL); } dp = devm_kzalloc(dev, sizeof(struct analogix_dp_device), GFP_KERNEL); if (!dp) return ERR_PTR(-ENOMEM); dp->dev = &pdev->dev; dp->dpms_mode = DRM_MODE_DPMS_OFF; mutex_init(&dp->panel_lock); dp->panel_is_modeset = false; /* * platform dp driver need containor_of the plat_data to get * the driver private data, so we need to store the point of * plat_data, not the context of plat_data. */ dp->plat_data = plat_data; ret = analogix_dp_dt_parse_pdata(dp); if (ret) return ERR_PTR(ret); dp->phy = devm_phy_get(dp->dev, "dp"); if (IS_ERR(dp->phy)) { dev_err(dp->dev, "no DP phy configured\n"); ret = PTR_ERR(dp->phy); if (ret) { /* * phy itself is not enabled, so we can move forward * assigning NULL to phy pointer. */ if (ret == -ENOSYS || ret == -ENODEV) dp->phy = NULL; else return ERR_PTR(ret); } } dp->clock = devm_clk_get(&pdev->dev, "dp"); if (IS_ERR(dp->clock)) { dev_err(&pdev->dev, "failed to get clock\n"); return ERR_CAST(dp->clock); } clk_prepare_enable(dp->clock); res = platform_get_resource(pdev, IORESOURCE_MEM, 0); dp->reg_base = devm_ioremap_resource(&pdev->dev, res); if (IS_ERR(dp->reg_base)) return ERR_CAST(dp->reg_base); dp->force_hpd = of_property_read_bool(dev->of_node, "force-hpd"); dp->hpd_gpio = of_get_named_gpio(dev->of_node, "hpd-gpios", 0); if (!gpio_is_valid(dp->hpd_gpio)) dp->hpd_gpio = of_get_named_gpio(dev->of_node, "samsung,hpd-gpio", 0); if (gpio_is_valid(dp->hpd_gpio)) { /* * Set up the hotplug GPIO from the device tree as an interrupt. * Simply specifying a different interrupt in the device tree * doesn't work since we handle hotplug rather differently when * using a GPIO. We also need the actual GPIO specifier so * that we can get the current state of the GPIO. */ ret = devm_gpio_request_one(&pdev->dev, dp->hpd_gpio, GPIOF_IN, "hpd_gpio"); if (ret) { dev_err(&pdev->dev, "failed to get hpd gpio\n"); return ERR_PTR(ret); } dp->irq = gpio_to_irq(dp->hpd_gpio); irq_flags = IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING; } else { dp->hpd_gpio = -ENODEV; dp->irq = platform_get_irq(pdev, 0); irq_flags = 0; } if (dp->irq == -ENXIO) { dev_err(&pdev->dev, "failed to get irq\n"); return ERR_PTR(-ENODEV); } ret = devm_request_threaded_irq(&pdev->dev, dp->irq, analogix_dp_hardirq, analogix_dp_irq_thread, irq_flags, "analogix-dp", dp); if (ret) { dev_err(&pdev->dev, "failed to request irq\n"); goto err_disable_pm_runtime; } disable_irq(dp->irq); dp->drm_dev = drm_dev; dp->encoder = dp->plat_data->encoder; dp->aux.name = "DP-AUX"; dp->aux.transfer = analogix_dpaux_transfer; dp->aux.dev = &pdev->dev; ret = drm_dp_aux_register(&dp->aux); if (ret) return ERR_PTR(ret); pm_runtime_enable(dev); ret = analogix_dp_create_bridge(drm_dev, dp); if (ret) { DRM_ERROR("failed to create bridge (%d)\n", ret); goto err_disable_pm_runtime; } return dp; err_disable_pm_runtime: pm_runtime_disable(dev); return ERR_PTR(ret); } EXPORT_SYMBOL_GPL(analogix_dp_bind); void analogix_dp_unbind(struct analogix_dp_device *dp) { analogix_dp_bridge_disable(dp->bridge); dp->connector.funcs->destroy(&dp->connector); if (dp->plat_data->panel) { if (drm_panel_unprepare(dp->plat_data->panel)) DRM_ERROR("failed to turnoff the panel\n"); if (drm_panel_detach(dp->plat_data->panel)) DRM_ERROR("failed to detach the panel\n"); } drm_dp_aux_unregister(&dp->aux); pm_runtime_disable(dp->dev); clk_disable_unprepare(dp->clock); } EXPORT_SYMBOL_GPL(analogix_dp_unbind); #ifdef CONFIG_PM int analogix_dp_suspend(struct analogix_dp_device *dp) { clk_disable_unprepare(dp->clock); if (dp->plat_data->panel) { if (drm_panel_unprepare(dp->plat_data->panel)) DRM_ERROR("failed to turnoff the panel\n"); } return 0; } EXPORT_SYMBOL_GPL(analogix_dp_suspend); int analogix_dp_resume(struct analogix_dp_device *dp) { int ret; ret = clk_prepare_enable(dp->clock); if (ret < 0) { DRM_ERROR("Failed to prepare_enable the clock clk [%d]\n", ret); return ret; } if (dp->plat_data->panel) { if (drm_panel_prepare(dp->plat_data->panel)) { DRM_ERROR("failed to setup the panel\n"); return -EBUSY; } } return 0; } EXPORT_SYMBOL_GPL(analogix_dp_resume); #endif int analogix_dp_start_crc(struct drm_connector *connector) { struct analogix_dp_device *dp = to_dp(connector); if (!connector->state->crtc) { DRM_ERROR("Connector %s doesn't currently have a CRTC.\n", connector->name); return -EINVAL; } return drm_dp_start_crc(&dp->aux, connector->state->crtc); } EXPORT_SYMBOL_GPL(analogix_dp_start_crc); int analogix_dp_stop_crc(struct drm_connector *connector) { struct analogix_dp_device *dp = to_dp(connector); return drm_dp_stop_crc(&dp->aux); } EXPORT_SYMBOL_GPL(analogix_dp_stop_crc); MODULE_AUTHOR("Jingoo Han "); MODULE_DESCRIPTION("Analogix DP Core Driver"); MODULE_LICENSE("GPL v2");