#include "4912.dtsi"
#include "../bcm_voice.dtsi"

/ {
	memory_controller {
		memcfg = <(BP_DDR_TYPE_DDR4           | \
			BP_DDR_SPEED_1600_22_22_22    | \
			BP_DDR_TOTAL_SIZE_2048MB      | \
			BP_DDR_DEVICE_WIDTH_16        | \
			BP_DDR_TOTAL_WIDTH_32BIT      | \
			BP_DDR_4912_DEFAULT)>;
	};

	buttons: buttons {
		compatible = "brcm,buttons";
		reset_button {
			ext_irq = <&bca_extintr 51 GPIO_ACTIVE_LOW (BCA_EXTINTR_TYPE_LOW_LEVEL | BCA_EXTINTR_TYPE_SENSE_EDGE)>;
			press {
				print = "Button Press -- Hold for 5s to do restore to default";
			};
			hold {
				rst_to_dflt = <5>;
			};
			release {
				reset = <0>;
			};	
		};
		ses_button {
			ext_irq = <&bca_extintr 52 GPIO_ACTIVE_LOW (BCA_EXTINTR_TYPE_LOW_LEVEL | BCA_EXTINTR_TYPE_SENSE_EDGE)>;
			release {
				ses_short_period = <0>;
				ses_long_period = <3>;
			};
		};		
	};

	sfp0: sfp0 {
		compatible = "brcm,sfp";
		pinctrl-names = "default", "rx-sd";
		pinctrl-0 = <&serdes2_rx_los_pin_2>;
		pinctrl-1 = <&serdes2_rx_los_pin_2>;
		i2c-bus = <&i2c1>;
		mod-def0 = <&bca_extintr 5 GPIO_ACTIVE_LOW (BCA_EXTINTR_TYPE_BOTH_EDGE | BCA_EXTINTR_TYPE_SENSE_EDGE)>;
	};

};

&nand {
	write-protect = <1>;
};

#if defined(CONFIG_BCM_PCIE_HCD) || defined(CONFIG_BCM_PCIE_HCD_MODULE)
&pcie1 {
	status = "okay";
};
#endif //#if defined(CONFIG_BCM_PCIE_HCD) || defined(CONFIG_BCM_PCIE_HCD_MODULE)

&i2c1 {
	pinctrl-names = "default";
	pinctrl-0 = <&i2c1_sclk_pin_14 &i2c1_sdata_pin_15>;
	status = "okay";
};

&mdio {
	phy4:4 {
		status = "okay";
	};
	phy1:1 {
		status = "okay";
	};
	phy_rgmii: rgmii {
		status = "disabled";
	};

	phy_cascade0:9 {
		status = "okay";
	};

	phy_serdes0:6 {
		phy-handle = <&phy_cascade0>;
		status = "okay";
	};

	phy_serdes2:8 {
		trx = <&sfp0>;
		status = "okay";
	};
};

&switch0 {
	ports {
		port0@0 {
			status = "okay";
		};
		port3@3 {
			network-leds = <&led6 &led7>;
			status = "okay";
		};

		port5@5 {
			network-leds = <&led8 &led9>;
			status = "okay";
		};

		port7@7 {
			network-leds = <&led12 &led13>;
			status = "okay";
		};
	};
};

&legacy_leds {
    wl-sess-led = <&led15>;
};

&led_ctrl {
    pinctrl-names = "default";
    pinctrl-0 = <&ser_led_clk_pin_17 &ser_led_data_pin_16 &ser_led_mask_pin_18>;
    serial-shifters-installed = <2>;
    serial-data-polarity-high;

    led0:sw_serial_led_0 {
        status = "okay";
        active_high;
	crossbar-output = <0>;
    };
    led1:sw_serial_led_1 {
	crossbar-output = <1>;
        active_high;
        status = "okay";
    };
    led2:sw_serial_led_2 {
        status = "okay";
        active_high;
	crossbar-output = <2>;
    };
    led3:sw_serial_led_3 {
        status = "okay";
        active_high;
	crossbar-output = <3>;
    };
    led4:sw_serial_led_4 {
        status = "okay";
        active_high;
	crossbar-output = <4>;
    };
    led5:sw_serial_led_5 {
        status = "okay";
        active_high;
	crossbar-output = <5>;
    };
    led6: serial-port_3-led_0 {
        active_high;
        link = <(LED_SPEED_100)>;
        activity = <(LED_SPEED_100)>;
	crossbar-output = <9>;
        status = "okay";
    };
    led7: serial-port_3-led_1 {
        active_high;
        link = <(LED_SPEED_1G)>;
        activity = <(LED_SPEED_1G)>;
	crossbar-output = <10>;
        status = "okay";
    };
    led8: serial-port_5-led_0 {
        active_high;
        link = <(LED_SPEED_100|LED_SPEED_2500)>;
        activity = <(LED_SPEED_100|LED_SPEED_2500)>;
	crossbar-output = <15>;
        status = "okay";
    };
    led9: serial-port_5-led_1 {
        active_high;
        link = <(LED_SPEED_1G|LED_SPEED_2500)>;
        activity = <(LED_SPEED_1G|LED_SPEED_2500)>;
	crossbar-output = <16>;
        status = "okay";
    };
    led10: serial-port_6-led_0 {
        active_high;
        link = <(LED_SPEED_100|LED_SPEED_2500|LED_SPEED_10G)>;
        activity = <(LED_SPEED_100|LED_SPEED_2500|LED_SPEED_10G)>;
	crossbar-output = <18>;
        status = "okay";
    };
    led11: serial-port_6-led_1 {
        active_high;
        link = <(LED_SPEED_1G|LED_SPEED_2500|LED_SPEED_10G)>;
        activity = <(LED_SPEED_1G|LED_SPEED_2500|LED_SPEED_10G)>;
	crossbar-output = <19>;
        status = "okay";
    };
    led12: serial-port_7-led_0 {
        active_high;
        link = <(LED_SPEED_100|LED_SPEED_2500|LED_SPEED_10G)>;
        activity = <(LED_SPEED_100|LED_SPEED_2500|LED_SPEED_10G)>;
	crossbar-output = <21>;
        status = "okay";
    };
    led13: serial-port_7-led_1 {
        active_high;
        link = <(LED_SPEED_1G|LED_SPEED_2500|LED_SPEED_10G)>;
        activity = <(LED_SPEED_1G|LED_SPEED_2500|LED_SPEED_10G)>;
	crossbar-output = <22>;
        status = "okay";
    };
    led14: sw_serial_led_30 {
        active_high;
        label = "INET";
        crossbar-output = <23>;
        status = "okay";
    };
    led15: sw_serial_led_31 {
        active_high;
        label = "WPS";
        crossbar-output = <31>;
        status = "okay";
    };
};

&vreg_sync {
		pinctrl-0 = <&a_vreg_sync_pin_19>;
		pinctrl-names = "default";
};
&uart0 {
        pinctrl-names = "default";
        pinctrl-0 = <&uart0_sdin_pin_56 &uart0_sdout_pin_57 >;
        status = "okay";
};