#include "6756.dtsi"

/ {
	memory_controller {
		memcfg = <(BP_DDR_TYPE_DDR4           | \
			BP_DDR_SPEED_1067_15_15_15 | \
			BP_DDR_TOTAL_SIZE_2048MB   | \
			BP_DDR_DEVICE_WIDTH_8      | \
			BP_DDR_TOTAL_WIDTH_16BIT   | \
			BP_DDR_6756_DEFAULT)>;
	};

	buttons {
		compatible = "brcm,buttons";
		ses_button {
			ext_irq = <&bca_extintr 4 GPIO_ACTIVE_LOW (BCA_EXTINTR_TYPE_LOW_LEVEL | BCA_EXTINTR_TYPE_SENSE_EDGE)>;
			release {
				ses_short_period = <0>;
				ses_long_period = <3>;
			};
		};
	};
	switch_sf2_ext:0 {
	};
};

&sysport {
    ethsw_ext = <&switch_sf2_ext>;
};

&mdio_sf2 {
	phy_cascade0:cascade0 {
		reg = <9>;
		phy-reset = <&gpioc 33 GPIO_ACTIVE_LOW>;
		enet-phy-lane-swap;
		status = "okay";
	};
	phy_serdes0:serdes0 {
		phy-handle = <&phy_cascade0>;
		status = "okay";    /* HSGMII 5GE */
	};
	phy_serdes1:serdes1 {
		phy-extswitch;
		config_speed = <2500>;
		status = "okay";
	};
	/* PHYs on external SF2 switch */
	sf2_gphy0:0 {
		compatible = "brcm,bcaphy";
		phy-type = "EGPHY";
		reg = <0>;
		status = "okay";
	};
	sf2_gphy1:1 {
		compatible = "brcm,bcaphy";
		phy-type = "EGPHY";
		reg = <1>;
		status = "okay";
	};
	sf2_gphy2:2 {
		compatible = "brcm,bcaphy";
		phy-type = "EGPHY";
		reg = <2>;
		status = "okay";
	};
	sf2_gphy3:3 {
		compatible = "brcm,bcaphy";
		phy-type = "EGPHY";
		reg = <3>;
		status = "okay";
	};
};

&switch0 {
	pinctrl-names = "default";
	pinctrl-0 = <&a_rgmii_mdc_pin_68 &a_rgmii_mdio_pin_69>;

	ports {
		port5@5 {
			phy-handle = <&phy_serdes0>;
			status = "okay";
		};
		port6@6 {
			phy-handle = <&phy_serdes1>;
			link = <&switch_sf2_ext>;           /* root.p1 <--> sf2_ext.p8 */
			shrink-ipg;
			status = "okay";
		};
	};
};

&switch_sf2_ext {                       /* linux/uboot: external sf2 */
	unit = <1>;
	sw-type = "SF2_SW";

	compatible = "brcm,bcmbca-extsw";
	extswsgmii_addr = <0x7>;
	switch-reset = <&gpioc 32 GPIO_ACTIVE_LOW>;

	ports {
		#address-cells = <1>;
		#size-cells = <0>;

		sf2_port0@0 {
			phy-handle = <&sf2_gphy0>;
			reg = <0>;
			mac-type = "SF2MAC";
			phy-mode = "gmii";
			gmii-direct;
			status = "okay";
		};
		sf2_port1@1 {
			phy-handle = <&sf2_gphy1>;
			reg = <1>;
			mac-type = "SF2MAC";
			phy-mode = "gmii";
			gmii-direct;
			status = "okay";
		};
		sf2_port2@2 {
			phy-handle = <&sf2_gphy2>;
			reg = <2>;
			mac-type = "SF2MAC";
			phy-mode = "gmii";
			gmii-direct;
			status = "okay";
		};
		sf2_port3@3 {
			phy-handle = <&sf2_gphy3>;
			reg = <3>;
			mac-type = "SF2MAC";
			phy-mode = "gmii";
			gmii-direct;
			status = "okay";
		};
		sf2_port8@8 {
			management;                     /* sf2_ext.p8 <--> root.p1 */
			reg = <8>;
			mac-type = "SF2MAC";
			shrink-ipg;
			phy-mode = "gmii";
			gmii-direct;
			status = "okay";
		};
	};
};

&sdhci {
	pinctrl-names="default";
	pinctrl-0 = <&emmc_ctrl_pins>;
	status = "okay";
};