rshd
****

The rshd server is the server for the rcmd(3) routine and, consequently, for the rsh(1) program.  The server provides remote execution facilities with authentication based on privileged port numbers from trusted hosts.  The rshd server listens for service requests at the port indicated in the ``cmd'' service specification; see services(5).  When a service request is received the following protocol is initiated:

 1. The server checks the client's source port.  If the port is not in the range 512-1023, the server aborts the connection.

 2. The server reads characters from the socket up to a null (`\0') byte.  The resultant string is interpreted as an ASCII number, base 10.

 3. If the number received in step 2 is non-zero, it is interpreted as the port number of a secondary stream to be used for the stderr. A second connection is then created to the specified port on the client's machine.  The source port of this second connection is also in the range 512-1023.

 4. The server checks the client's source address and requests the corresponding host name (see gethostbyaddr(3),  hosts(5) and named(8)).  If the hostname cannot be determined, the dot-notation representation of the host address is used.  If the hostname is in the same domain as the server (according to the last two components of the domain name), or if the -a option is given, the addresses for the hostname are requested, verifying that the name and address correspond.  If address verification fails, the connection is aborted with the message, ``Host address mismatch.''

 5. A null terminated user name of at most 16 characters is retrieved on the initial socket.  This user name is interpreted as the user identity on the client's machine.

 6. A null terminated user name of at most 16 characters is retrieved on the initial socket.  This user name is interpreted as a user identity to use on the server's machine.

 7. A null terminated command to be passed to a shell is retrieved on the initial socket.  The length of the command is limited by the upper bound on the size of the system's argument list.

 8. Rshd then validates the user using ruserok(3),  which uses the file /etc/hosts.equiv and the .rhosts file found in the user's home directory. The -l option prevents ruserok(3) from doing any validation based on the user's ``.rhosts'' file, unless the user is the superuser.

 9. If the file /etc/nologin exists and the user is not the superuser, the connection is closed.

 10. A null byte is returned on the initial socket and the command line is passed to the normal login shell of the user.  The shell inherits the network connections established by rshd.

 11. Transport-level keepalive messages are enabled unless the -n option is present.  The use of keepalive messages allows sessions to be timed out if the client crashes or becomes unreachable.

 12. The -L option causes all successful accesses to be logged to syslogd(8) as auth.info messages.

See ruserok (The GNU C Library Reference Manual), for details.

Invoking
========

The options are as follows :

-a
--verify-hostname
     Ask hostname for verification.

-l
--no-rhosts
     Ignore .rhosts file.

-L
--local-domain=NAME
     Set local domain name.

-n
--no-keepalive
     Do not set SO_KEEPALIVE.

-k
--kerberos
     Use kerberos IV authentication.

-x
--encrypt
     Turns on DES encryption for all data passed via the rshd session. This may impact response time and CPU utilization, but provides increased security.

-D
--debug[=LEVEL]
     Set debug level, not implemented.

-h
--help
     Display usage instructions.

-V
--version
     Display program version.

Diagnostics
===========

Except for the last one listed below, all diagnostic messages are returned on the initial socket, after which any network connections are closed.  An error is indicated by a leading byte with a value of 1 (0 is returned in step 10 above upon successful completion of all the steps prior to the execution of the login shell).

Locuser too long
     The name of the user on the client's machine is longer than 16 characters.

Ruser too long
     The name of the user on the remote machine is longer than 16 characters.

Command too long
     The command line passed exceeds the size of the argument list (as configured into the system).

Login incorrect
     No password file entry for the user name existed.

Remote directory
     The chdir command to the home directory failed.

Permission denied
     The authentication procedure described above failed.

Can't make pipe.
     The pipe needed for the stderr, wasn't created.

Can't fork; try again.
     A fork by the server failed.

<shellname>: ...
     The user's login shell could not be started.  This message is re- turned on the connection associated with the stderr, and is not preceded by a flag byte.

The authentication procedure used here assumes the integrity of each client machine and the connecting medium.  This is insecure, but is useful in an ``open'' environment.