# # SPI driver configuration # # NOTE: the reason this doesn't show SPI slave support is mostly that # nobody's needed a slave side API yet. The master-role API is not # fully appropriate there, so it'd need some thought to do well. # menu "SPI support" config SPI bool "SPI support" help The "Serial Peripheral Interface" is a low level synchronous protocol. Chips that support SPI can have data transfer rates up to several tens of Mbit/sec. Chips are addressed with a controller and a chipselect. Most SPI slaves don't support dynamic device discovery; some are even write-only or read-only. SPI is widely used by microcontollers to talk with sensors, eeprom and flash memory, codecs and various other controller chips, analog to digital (and d-to-a) converters, and more. MMC and SD cards can be accessed using SPI protocol; and for DataFlash cards used in MMC sockets, SPI must always be used. SPI is one of a family of similar protocols using a four wire interface (select, clock, data in, data out) including Microwire (half duplex), SSP, SSI, and PSP. This driver framework should work with most such devices and controllers. config SPI_DEBUG boolean "Debug support for SPI drivers" depends on SPI && DEBUG_KERNEL help Say "yes" to enable debug messaging (like dev_dbg and pr_debug), sysfs, and debugfs support in SPI controller and protocol drivers. # # MASTER side ... talking to discrete SPI slave chips including microcontrollers # config SPI_MASTER # boolean "SPI Master Support" boolean default SPI help If your system has an master-capable SPI controller (which provides the clock and chipselect), you can enable that controller and the protocol drivers for the SPI slave chips that are connected. comment "SPI Master Controller Drivers" depends on SPI_MASTER config SPI_BITBANG tristate "Bitbanging SPI master" depends on SPI_MASTER && EXPERIMENTAL help With a few GPIO pins, your system can bitbang the SPI protocol. Select this to get SPI support through I/O pins (GPIO, parallel port, etc). Or, some systems' SPI master controller drivers use this code to manage the per-word or per-transfer accesses to the hardware shift registers. This is library code, and is automatically selected by drivers that need it. You only need to select this explicitly to support driver modules that aren't part of this kernel tree. config SPI_BUTTERFLY tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)" depends on SPI_MASTER && PARPORT && EXPERIMENTAL select SPI_BITBANG help This uses a custom parallel port cable to connect to an AVR Butterfly , an inexpensive battery powered microcontroller evaluation board. This same cable can be used to flash new firmware. config SPI_MPC83xx tristate "Freescale MPC83xx SPI controller" depends on SPI_MASTER && PPC_83xx && EXPERIMENTAL select SPI_BITBANG help This enables using the Freescale MPC83xx SPI controller in master mode. Note, this driver uniquely supports the SPI controller on the MPC83xx family of PowerPC processors. The MPC83xx uses a simple set of shift registers for data (opposed to the CPM based descriptor model). config SPI_PXA2XX tristate "PXA2xx SSP SPI master" depends on SPI_MASTER && ARCH_PXA && EXPERIMENTAL help This enables using a PXA2xx SSP port as a SPI master controller. The driver can be configured to use any SSP port and additional documentation can be found a Documentation/spi/pxa2xx. config SPI_S3C24XX_GPIO tristate "Samsung S3C24XX series SPI by GPIO" depends on SPI_MASTER && ARCH_S3C2410 && SPI_BITBANG && EXPERIMENTAL help SPI driver for Samsung S3C24XX series ARM SoCs using GPIO lines to provide the SPI bus. This can be used where the inbuilt hardware cannot provide the transfer mode, or where the board is using non hardware connected pins. config SPI_OMAP_UWIRE tristate "OMAP MicroWire" depends on SPI_MASTER && ARCH_OMAP select SPI_BITBANG help This hooks up to the MicroWire controller on OMAP chips. config SPI_OMAP24XX bool "McSPI driver for OMAP24xx" depends on SPI_MASTER && ARCH_OMAP24XX help SPI master controller for OMAP24xx McSPI modules. # # Add new SPI master controllers in alphabetical order above this line # config SPI_S3C24XX tristate "Samsung S3C24XX series SPI" depends on SPI_MASTER && ARCH_S3C2410 && EXPERIMENTAL help SPI driver for Samsung S3C24XX series ARM SoCs # # There are lots of SPI device types, with sensors and memory # being probably the most widely used ones. # comment "SPI Protocol Masters" depends on SPI_MASTER config TSC2102 depends on SPI_MASTER tristate "TSC2102 codec support" ---help--- Say Y here if you want support for the TSC2102 chip. It will be needed for the touchscreen driver on some boards. # # Add new SPI protocol masters in alphabetical order above this line # # (slave support would go here) endmenu # "SPI support"