/* LzmaDec.h -- LZMA Decoder
2009-02-07 : Igor Pavlov : Public domain */

#ifndef __LZMA_DEC_H
#define __LZMA_DEC_H

#include "Types.h"

#ifdef __cplusplus
extern "C" {
#endif

/* #define _LZMA_PROB32 */
/* _LZMA_PROB32 can increase the speed on some CPUs,
   but memory usage for CLzmaDec::probs will be doubled in that case */

#ifdef _LZMA_PROB32
#define CLzmaProb UInt32
#else
#define CLzmaProb UInt16
#endif

/* ---------- LZMA Properties ---------- */

#define LZMA_PROPS_SIZE 5

typedef struct _CLzmaProps {
	unsigned lc, lp, pb;
	UInt32 dicSize;
} CLzmaProps;

/* ---------- LZMA Decoder state ---------- */

/* LZMA_REQUIRED_INPUT_MAX = number of required input bytes for worst case.
   Num bits = log2((2^11 / 31) ^ 22) + 26 < 134 + 26 = 160; */

#define LZMA_REQUIRED_INPUT_MAX 20

typedef struct
{
	CLzmaProps prop;
	CLzmaProb *probs;
	Byte *dic;
	const Byte *buf;
	UInt32 range, code;
	SizeT dicPos;
	SizeT dicBufSize;
	UInt32 processedPos;
	UInt32 checkDicSize;
	unsigned state;
	UInt32 reps[4];
	unsigned remainLen;
	int needFlush;
	int needInitState;
	UInt32 numProbs;
	unsigned tempBufSize;
	Byte tempBuf[LZMA_REQUIRED_INPUT_MAX];
} CLzmaDec;

#define LzmaDec_Construct(p)    \
	{                       \
		(p)->dic = 0;   \
		(p)->probs = 0; \
	}

/* There are two types of LZMA streams:
     0) Stream with end mark. That end mark adds about 6 bytes to compressed size.
     1) Stream without end mark. You must know exact uncompressed size to decompress such stream. */

typedef enum {
	LZMA_FINISH_ANY, /* finish at any point */
	LZMA_FINISH_END /* block must be finished at the end */
} ELzmaFinishMode;

/* ELzmaFinishMode has meaning only if the decoding reaches output limit !!!

   You must use LZMA_FINISH_END, when you know that current output buffer
   covers last bytes of block. In other cases you must use LZMA_FINISH_ANY.

   If LZMA decoder sees end marker before reaching output limit, it returns SZ_OK,
   and output value of destLen will be less than output buffer size limit.
   You can check status result also.

   You can use multiple checks to test data integrity after full decompression:
     1) Check Result and "status" variable.
     2) Check that output(destLen) = uncompressedSize, if you know real uncompressedSize.
     3) Check that output(srcLen) = compressedSize, if you know real compressedSize.
        You must use correct finish mode in that case. */

typedef enum {
	LZMA_STATUS_NOT_SPECIFIED, /* use main error code instead */
	LZMA_STATUS_FINISHED_WITH_MARK, /* stream was finished with end mark. */
	LZMA_STATUS_NOT_FINISHED, /* stream was not finished */
	LZMA_STATUS_NEEDS_MORE_INPUT, /* you must provide more input bytes */
	LZMA_STATUS_MAYBE_FINISHED_WITHOUT_MARK /* there is probability that stream was finished without end mark */
} ELzmaStatus;

/* ELzmaStatus is used only as output value for function call */

/* ---------- One Call Interface ---------- */

/* LzmaDecode

finishMode:
  It has meaning only if the decoding reaches output limit (*destLen).
  LZMA_FINISH_ANY - Decode just destLen bytes.
  LZMA_FINISH_END - Stream must be finished after (*destLen).

Returns:
  SZ_OK
    status:
      LZMA_STATUS_FINISHED_WITH_MARK
      LZMA_STATUS_NOT_FINISHED
      LZMA_STATUS_MAYBE_FINISHED_WITHOUT_MARK
  SZ_ERROR_DATA - Data error
  SZ_ERROR_MEM  - Memory allocation error
  SZ_ERROR_UNSUPPORTED - Unsupported properties
  SZ_ERROR_INPUT_EOF - It needs more bytes in input buffer (src).
*/

SRes LzmaDecode(Byte *dest, SizeT *destLen, const Byte *src, SizeT *srcLen,
		const Byte *propData, unsigned propSize, ELzmaFinishMode finishMode,
		ELzmaStatus *status, ISzAlloc *alloc);

#ifdef __cplusplus
}
#endif

#endif