# # SATA/PATA driver configuration # config HAVE_PATA_PLATFORM bool help This is an internal configuration node for any machine that uses pata-platform driver to enable the relevant driver in the configuration structure without having to submit endless patches to update the PATA_PLATFORM entry. menuconfig ATA tristate "Serial ATA and Parallel ATA drivers (libata)" depends on HAS_IOMEM depends on BLOCK depends on !(M32R || M68K || S390) || BROKEN select SCSI select GLOB ---help--- If you want to use an ATA hard disk, ATA tape drive, ATA CD-ROM or any other ATA device under Linux, say Y and make sure that you know the name of your ATA host adapter (the card inside your computer that "speaks" the ATA protocol, also called ATA controller), because you will be asked for it. NOTE: ATA enables basic SCSI support; *however*, 'SCSI disk support', 'SCSI tape support', or 'SCSI CDROM support' may also be needed, depending on your hardware configuration. if ATA config ATA_NONSTANDARD bool default n config ATA_VERBOSE_ERROR bool "Verbose ATA error reporting" default y help This option adds parsing of ATA command descriptions and error bits in libata kernel output, making it easier to interpret. This option will enlarge the kernel by approx. 6KB. Disable it only if kernel size is more important than ease of debugging. If unsure, say Y. config ARCH_WANT_LIBATA_LEDS bool config ATA_LEDS bool "support ATA port LED triggers" depends on ARCH_WANT_LIBATA_LEDS select NEW_LEDS select LEDS_CLASS select LEDS_TRIGGERS default y help This option adds a LED trigger for each registered ATA port. It is used to drive disk activity leds connected via GPIO. If unsure, say N. config ATA_ACPI bool "ATA ACPI Support" depends on ACPI default y help This option adds support for ATA-related ACPI objects. These ACPI objects add the ability to retrieve taskfiles from the ACPI BIOS and write them to the disk controller. These objects may be related to performance, security, power management, or other areas. You can disable this at kernel boot time by using the option libata.noacpi=1 config SATA_ZPODD bool "SATA Zero Power Optical Disc Drive (ZPODD) support" depends on ATA_ACPI && PM default n help This option adds support for SATA Zero Power Optical Disc Drive (ZPODD). It requires both the ODD and the platform support, and if enabled, will automatically power on/off the ODD when certain condition is satisfied. This does not impact end user's experience of the ODD, only power is saved when the ODD is not in use (i.e. no disc inside). If unsure, say N. config SATA_PMP bool "SATA Port Multiplier support" default y help This option adds support for SATA Port Multipliers (the SATA version of an ethernet hub, or SAS expander). comment "Controllers with non-SFF native interface" config SATA_AHCI tristate "AHCI SATA support" depends on PCI help This option enables support for AHCI Serial ATA. If unsure, say N. config SATA_AHCI_PLATFORM tristate "Platform AHCI SATA support" help This option enables support for Platform AHCI Serial ATA controllers. If unsure, say N. config AHCI_BRCM tristate "Broadcom AHCI SATA support" depends on ARCH_BRCMSTB || BMIPS_GENERIC || ARCH_BCM_NSP || \ ARCH_BCM_63XX help This option enables support for the AHCI SATA3 controller found on Broadcom SoC's. If unsure, say N. config AHCI_DA850 tristate "DaVinci DA850 AHCI SATA support" depends on ARCH_DAVINCI_DA850 help This option enables support for the DaVinci DA850 SoC's onboard AHCI SATA. If unsure, say N. config AHCI_ST tristate "ST AHCI SATA support" depends on ARCH_STI help This option enables support for ST AHCI SATA controller. If unsure, say N. config AHCI_IMX tristate "Freescale i.MX AHCI SATA support" depends on MFD_SYSCON && (ARCH_MXC || COMPILE_TEST) help This option enables support for the Freescale i.MX SoC's onboard AHCI SATA. If unsure, say N. config AHCI_CEVA tristate "CEVA AHCI SATA support" depends on OF help This option enables support for the CEVA AHCI SATA. It can be found on the Xilinx Zynq UltraScale+ MPSoC. If unsure, say N. config AHCI_MVEBU tristate "Marvell EBU AHCI SATA support" depends on ARCH_MVEBU help This option enables support for the Marvebu EBU SoC's onboard AHCI SATA. If unsure, say N. config AHCI_OCTEON tristate "Cavium Octeon Soc Serial ATA" depends on SATA_AHCI_PLATFORM && CAVIUM_OCTEON_SOC default y help This option enables support for Cavium Octeon SoC Serial ATA. If unsure, say N. config AHCI_SUNXI tristate "Allwinner sunxi AHCI SATA support" depends on ARCH_SUNXI help This option enables support for the Allwinner sunxi SoC's onboard AHCI SATA. If unsure, say N. config AHCI_TEGRA tristate "NVIDIA Tegra124 AHCI SATA support" depends on ARCH_TEGRA help This option enables support for the NVIDIA Tegra124 SoC's onboard AHCI SATA. If unsure, say N. config AHCI_XGENE tristate "APM X-Gene 6.0Gbps AHCI SATA host controller support" depends on PHY_XGENE help This option enables support for APM X-Gene SoC SATA host controller. config AHCI_QORIQ tristate "Freescale QorIQ AHCI SATA support" depends on OF help This option enables support for the Freescale QorIQ AHCI SoC's onboard AHCI SATA. If unsure, say N. config SATA_FSL tristate "Freescale 3.0Gbps SATA support" depends on FSL_SOC help This option enables support for Freescale 3.0Gbps SATA controller. It can be found on MPC837x and MPC8315. If unsure, say N. config SATA_AHCI_SEATTLE tristate "AMD Seattle 6.0Gbps AHCI SATA host controller support" depends on ARCH_SEATTLE help This option enables support for AMD Seattle SATA host controller. If unsure, say N config SATA_INIC162X tristate "Initio 162x SATA support (Very Experimental)" depends on PCI help This option enables support for Initio 162x Serial ATA. config SATA_ACARD_AHCI tristate "ACard AHCI variant (ATP 8620)" depends on PCI help This option enables support for Acard. If unsure, say N. config SATA_SIL24 tristate "Silicon Image 3124/3132 SATA support" depends on PCI help This option enables support for Silicon Image 3124/3132 Serial ATA. If unsure, say N. config ATA_SFF bool "ATA SFF support (for legacy IDE and PATA)" default y help This option adds support for ATA controllers with SFF compliant or similar programming interface. SFF is the legacy IDE interface that has been around since the dawn of time. Almost all PATA controllers have an SFF interface. Many SATA controllers have an SFF interface when configured into a legacy compatibility mode. For users with exclusively modern controllers like AHCI, Silicon Image 3124, or Marvell 6440, you may choose to disable this unneeded SFF support. If unsure, say Y. if ATA_SFF comment "SFF controllers with custom DMA interface" config PDC_ADMA tristate "Pacific Digital ADMA support" depends on PCI help This option enables support for Pacific Digital ADMA controllers If unsure, say N. config PATA_OCTEON_CF tristate "OCTEON Boot Bus Compact Flash support" depends on CAVIUM_OCTEON_SOC help This option enables a polled compact flash driver for use with compact flash cards attached to the OCTEON boot bus. If unsure, say N. config SATA_QSTOR tristate "Pacific Digital SATA QStor support" depends on PCI help This option enables support for Pacific Digital Serial ATA QStor. If unsure, say N. config SATA_SX4 tristate "Promise SATA SX4 support (Experimental)" depends on PCI help This option enables support for Promise Serial ATA SX4. If unsure, say N. config ATA_BMDMA bool "ATA BMDMA support" depends on HAS_DMA default y help This option adds support for SFF ATA controllers with BMDMA capability. BMDMA stands for bus-master DMA and is the de facto DMA interface for SFF controllers. If unsure, say Y. if ATA_BMDMA comment "SATA SFF controllers with BMDMA" config ATA_PIIX tristate "Intel ESB, ICH, PIIX3, PIIX4 PATA/SATA support" depends on PCI help This option enables support for ICH5/6/7/8 Serial ATA and support for PATA on the Intel ESB/ICH/PIIX3/PIIX4 series host controllers. If unsure, say N. config SATA_DWC tristate "DesignWare Cores SATA support" depends on DMADEVICES select GENERIC_PHY help This option enables support for the on-chip SATA controller of the AppliedMicro processor 460EX. If unsure, say N. config SATA_DWC_OLD_DMA bool "Support old device trees" depends on SATA_DWC select DW_DMAC_CORE default y if 460EX help This option enables support for old device trees without the "dmas" property. config SATA_DWC_DEBUG bool "Debugging driver version" depends on SATA_DWC help This option enables debugging output in the driver. config SATA_DWC_VDEBUG bool "Verbose debug output" depends on SATA_DWC_DEBUG help This option enables the taskfile dumping and NCQ debugging. config SATA_HIGHBANK tristate "Calxeda Highbank SATA support" depends on HAS_DMA depends on ARCH_HIGHBANK || COMPILE_TEST help This option enables support for the Calxeda Highbank SoC's onboard SATA. If unsure, say N. config SATA_MV tristate "Marvell SATA support" depends on HAS_DMA depends on PCI || ARCH_DOVE || ARCH_MV78XX0 || \ ARCH_MVEBU || ARCH_ORION5X || COMPILE_TEST select GENERIC_PHY help This option enables support for the Marvell Serial ATA family. Currently supports 88SX[56]0[48][01] PCI(-X) chips, as well as the newer [67]042 PCI-X/PCIe and SOC devices. If unsure, say N. config SATA_NV tristate "NVIDIA SATA support" depends on PCI help This option enables support for NVIDIA Serial ATA. If unsure, say N. config SATA_PROMISE tristate "Promise SATA TX2/TX4 support" depends on PCI help This option enables support for Promise Serial ATA TX2/TX4. If unsure, say N. config SATA_RCAR tristate "Renesas R-Car SATA support" depends on ARCH_RENESAS || COMPILE_TEST help This option enables support for Renesas R-Car Serial ATA. If unsure, say N. config SATA_SIL tristate "Silicon Image SATA support" depends on PCI help This option enables support for Silicon Image Serial ATA. If unsure, say N. config SATA_SIS tristate "SiS 964/965/966/180 SATA support" depends on PCI select PATA_SIS help This option enables support for SiS Serial ATA on SiS 964/965/966/180 and Parallel ATA on SiS 180. The PATA support for SiS 180 requires additionally to enable the PATA_SIS driver in the config. If unsure, say N. config SATA_SVW tristate "ServerWorks Frodo / Apple K2 SATA support" depends on PCI help This option enables support for Broadcom/Serverworks/Apple K2 SATA support. If unsure, say N. config SATA_ULI tristate "ULi Electronics SATA support" depends on PCI help This option enables support for ULi Electronics SATA. If unsure, say N. config SATA_VIA tristate "VIA SATA support" depends on PCI help This option enables support for VIA Serial ATA. If unsure, say N. config SATA_VITESSE tristate "VITESSE VSC-7174 / INTEL 31244 SATA support" depends on PCI help This option enables support for Vitesse VSC7174 and Intel 31244 Serial ATA. If unsure, say N. comment "PATA SFF controllers with BMDMA" config PATA_ALI tristate "ALi PATA support" depends on PCI help This option enables support for the ALi ATA interfaces found on the many ALi chipsets. If unsure, say N. config PATA_AMD tristate "AMD/NVidia PATA support" depends on PCI help This option enables support for the AMD and NVidia PATA interfaces found on the chipsets for Athlon/Athlon64. If unsure, say N. config PATA_ARASAN_CF tristate "ARASAN CompactFlash PATA Controller Support" depends on ARCH_SPEAR13XX || COMPILE_TEST depends on DMADEVICES select DMA_ENGINE help Say Y here to support the ARASAN CompactFlash PATA controller config PATA_ARTOP tristate "ARTOP 6210/6260 PATA support" depends on PCI help This option enables support for ARTOP PATA controllers. If unsure, say N. config PATA_ATIIXP tristate "ATI PATA support" depends on PCI help This option enables support for the ATI ATA interfaces found on the many ATI chipsets. If unsure, say N. config PATA_ATP867X tristate "ARTOP/Acard ATP867X PATA support" depends on PCI help This option enables support for ARTOP/Acard ATP867X PATA controllers. If unsure, say N. config PATA_BF54X tristate "Blackfin 54x ATAPI support" depends on BF542 || BF548 || BF549 help This option enables support for the built-in ATAPI controller on Blackfin 54x family chips. If unsure, say N. config PATA_CMD64X tristate "CMD64x PATA support" depends on PCI help This option enables support for the CMD64x series chips except for the CMD640. If unsure, say N. config PATA_CS5520 tristate "CS5510/5520 PATA support" depends on PCI && (X86_32 || COMPILE_TEST) help This option enables support for the Cyrix 5510/5520 companion chip used with the MediaGX/Geode processor family. If unsure, say N. config PATA_CS5530 tristate "CS5530 PATA support" depends on PCI && (X86_32 || COMPILE_TEST) help This option enables support for the Cyrix/NatSemi/AMD CS5530 companion chip used with the MediaGX/Geode processor family. If unsure, say N. config PATA_CS5535 tristate "CS5535 PATA support (Experimental)" depends on PCI && X86_32 help This option enables support for the NatSemi/AMD CS5535 companion chip used with the Geode processor family. If unsure, say N. config PATA_CS5536 tristate "CS5536 PATA support" depends on PCI && (X86_32 || MIPS || COMPILE_TEST) help This option enables support for the AMD CS5536 companion chip used with the Geode LX processor family. If unsure, say N. config PATA_CYPRESS tristate "Cypress CY82C693 PATA support (Very Experimental)" depends on PCI help This option enables support for the Cypress/Contaq CY82C693 chipset found in some Alpha systems If unsure, say N. config PATA_EFAR tristate "EFAR SLC90E66 support" depends on PCI help This option enables support for the EFAR SLC90E66 IDE controller found on some older machines. If unsure, say N. config PATA_EP93XX tristate "Cirrus Logic EP93xx PATA support" depends on ARCH_EP93XX help This option enables support for the PATA controller in the Cirrus Logic EP9312 and EP9315 ARM CPU. If unsure, say N. config PATA_HPT366 tristate "HPT 366/368 PATA support" depends on PCI help This option enables support for the HPT 366 and 368 PATA controllers via the new ATA layer. If unsure, say N. config PATA_HPT37X tristate "HPT 370/370A/371/372/374/302 PATA support" depends on PCI help This option enables support for the majority of the later HPT PATA controllers via the new ATA layer. If unsure, say N. config PATA_HPT3X2N tristate "HPT 371N/372N/302N PATA support" depends on PCI help This option enables support for the N variant HPT PATA controllers via the new ATA layer. If unsure, say N. config PATA_HPT3X3 tristate "HPT 343/363 PATA support" depends on PCI help This option enables support for the HPT 343/363 PATA controllers via the new ATA layer If unsure, say N. config PATA_HPT3X3_DMA bool "HPT 343/363 DMA support" depends on PATA_HPT3X3 help This option enables DMA support for the HPT343/363 controllers. Enable with care as there are still some problems with DMA on this chipset. config PATA_ICSIDE tristate "Acorn ICS PATA support" depends on ARM && ARCH_ACORN help On Acorn systems, say Y here if you wish to use the ICS PATA interface card. This is not required for ICS partition support. If you are unsure, say N to this. config PATA_IMX tristate "PATA support for Freescale iMX" depends on ARCH_MXC help This option enables support for the PATA host available on Freescale iMX SoCs. If unsure, say N. config PATA_IT8213 tristate "IT8213 PATA support (Experimental)" depends on PCI help This option enables support for the ITE 821 PATA controllers via the new ATA layer. If unsure, say N. config PATA_IT821X tristate "IT8211/2 PATA support" depends on PCI help This option enables support for the ITE 8211 and 8212 PATA controllers via the new ATA layer, including RAID mode. If unsure, say N. config PATA_JMICRON tristate "JMicron PATA support" depends on PCI help Enable support for the JMicron IDE controller, via the new ATA layer. If unsure, say N. config PATA_MACIO tristate "Apple PowerMac/PowerBook internal 'MacIO' IDE" depends on PPC_PMAC help Most IDE capable PowerMacs have IDE busses driven by a variant of this controller which is part of the Apple chipset used on most PowerMac models. Some models have multiple busses using different chipsets, though generally, MacIO is one of them. config PATA_MARVELL tristate "Marvell PATA support via legacy mode" depends on PCI help This option enables limited support for the Marvell 88SE61xx ATA controllers. If you wish to use only the SATA ports then select the AHCI driver alone. If you wish to the use the PATA port or both SATA and PATA include this driver. If unsure, say N. config PATA_MPC52xx tristate "Freescale MPC52xx SoC internal IDE" depends on PPC_MPC52xx && PPC_BESTCOMM select PPC_BESTCOMM_ATA help This option enables support for integrated IDE controller of the Freescale MPC52xx SoC. If unsure, say N. config PATA_NETCELL tristate "NETCELL Revolution RAID support" depends on PCI help This option enables support for the Netcell Revolution RAID PATA controller. If unsure, say N. config PATA_NINJA32 tristate "Ninja32/Delkin Cardbus ATA support" depends on PCI help This option enables support for the Ninja32, Delkin and possibly other brands of Cardbus ATA adapter If unsure, say N. config PATA_NS87415 tristate "Nat Semi NS87415 PATA support" depends on PCI help This option enables support for the National Semiconductor NS87415 PCI-IDE controller. If unsure, say N. config PATA_OLDPIIX tristate "Intel PATA old PIIX support" depends on PCI help This option enables support for early PIIX PATA support. If unsure, say N. config PATA_OPTIDMA tristate "OPTI FireStar PATA support (Very Experimental)" depends on PCI help This option enables DMA/PIO support for the later OPTi controllers found on some old motherboards and in some laptops. If unsure, say N. config PATA_PDC2027X tristate "Promise PATA 2027x support" depends on PCI help This option enables support for Promise PATA pdc20268 to pdc20277 host adapters. If unsure, say N. config PATA_PDC_OLD tristate "Older Promise PATA controller support" depends on PCI help This option enables support for the Promise 20246, 20262, 20263, 20265 and 20267 adapters. If unsure, say N. config PATA_RADISYS tristate "RADISYS 82600 PATA support (Experimental)" depends on PCI help This option enables support for the RADISYS 82600 PATA controllers via the new ATA layer If unsure, say N. config PATA_RDC tristate "RDC PATA support" depends on PCI help This option enables basic support for the later RDC PATA controllers controllers via the new ATA layer. For the RDC 1010, you need to enable the IT821X driver instead. If unsure, say N. config PATA_SC1200 tristate "SC1200 PATA support" depends on PCI && (X86_32 || COMPILE_TEST) help This option enables support for the NatSemi/AMD SC1200 SoC companion chip used with the Geode processor family. If unsure, say N. config PATA_SCH tristate "Intel SCH PATA support" depends on PCI help This option enables support for Intel SCH PATA on the Intel SCH (US15W, US15L, UL11L) series host controllers. If unsure, say N. config PATA_SERVERWORKS tristate "SERVERWORKS OSB4/CSB5/CSB6/HT1000 PATA support" depends on PCI help This option enables support for the Serverworks OSB4/CSB5/CSB6 and HT1000 PATA controllers, via the new ATA layer. If unsure, say N. config PATA_SIL680 tristate "CMD / Silicon Image 680 PATA support" depends on PCI help This option enables support for CMD / Silicon Image 680 PATA. If unsure, say N. config PATA_SIS tristate "SiS PATA support" depends on PCI help This option enables support for SiS PATA controllers If unsure, say N. config PATA_TOSHIBA tristate "Toshiba Piccolo support (Experimental)" depends on PCI help Support for the Toshiba Piccolo controllers. Currently only the primary channel is supported by this driver. If unsure, say N. config PATA_TRIFLEX tristate "Compaq Triflex PATA support" depends on PCI help Enable support for the Compaq 'Triflex' IDE controller as found on many Compaq Pentium-Pro systems, via the new ATA layer. If unsure, say N. config PATA_VIA tristate "VIA PATA support" depends on PCI help This option enables support for the VIA PATA interfaces found on the many VIA chipsets. If unsure, say N. config PATA_PXA tristate "PXA DMA-capable PATA support" depends on ARCH_PXA help This option enables support for harddrive attached to PXA CPU's bus. NOTE: This driver utilizes PXA DMA controller, in case your hardware is not capable of doing MWDMA, use pata_platform instead. If unsure, say N. config PATA_WINBOND tristate "Winbond SL82C105 PATA support" depends on PCI help This option enables support for SL82C105 PATA devices found in the Netwinder and some other systems If unsure, say N. endif # ATA_BMDMA comment "PIO-only SFF controllers" config PATA_AT32 tristate "Atmel AVR32 PATA support (Experimental)" depends on AVR32 && PLATFORM_AT32AP help This option enables support for the IDE devices on the Atmel AT32AP platform. If unsure, say N. config PATA_AT91 tristate "PATA support for AT91SAM9260" depends on ARM && SOC_AT91SAM9 help This option enables support for IDE devices on the Atmel AT91SAM9260 SoC. If unsure, say N. config PATA_CMD640_PCI tristate "CMD640 PCI PATA support (Experimental)" depends on PCI help This option enables support for the CMD640 PCI IDE interface chip. Only the primary channel is currently supported. If unsure, say N. config PATA_ISAPNP tristate "ISA Plug and Play PATA support" depends on ISAPNP help This option enables support for ISA plug & play ATA controllers such as those found on old soundcards. If unsure, say N. config PATA_IXP4XX_CF tristate "IXP4XX Compact Flash support" depends on ARCH_IXP4XX help This option enables support for a Compact Flash connected on the ixp4xx expansion bus. This driver had been written for Loft/Avila boards in mind but can work with others. If unsure, say N. config PATA_MPIIX tristate "Intel PATA MPIIX support" depends on PCI help This option enables support for MPIIX PATA support. If unsure, say N. config PATA_NS87410 tristate "Nat Semi NS87410 PATA support" depends on PCI help This option enables support for the National Semiconductor NS87410 PCI-IDE controller. If unsure, say N. config PATA_OPTI tristate "OPTI621/6215 PATA support (Very Experimental)" depends on PCI help This option enables full PIO support for the early Opti ATA controllers found on some old motherboards. If unsure, say N. config PATA_PALMLD tristate "Palm LifeDrive PATA support" depends on MACH_PALMLD help This option enables support for Palm LifeDrive's internal ATA port via the new ATA layer. If unsure, say N. config PATA_PCMCIA tristate "PCMCIA PATA support" depends on PCMCIA help This option enables support for PCMCIA ATA interfaces, including compact flash card adapters via the new ATA layer. If unsure, say N. config PATA_PLATFORM tristate "Generic platform device PATA support" depends on EXPERT || PPC || HAVE_PATA_PLATFORM help This option enables support for generic directly connected ATA devices commonly found on embedded systems. If unsure, say N. config PATA_OF_PLATFORM tristate "OpenFirmware platform device PATA support" depends on PATA_PLATFORM && OF help This option enables support for generic directly connected ATA devices commonly found on embedded systems with OpenFirmware bindings. If unsure, say N. config PATA_QDI tristate "QDI VLB PATA support" depends on ISA select PATA_LEGACY help Support for QDI 6500 and 6580 PATA controllers on VESA local bus. config PATA_RB532 tristate "RouterBoard 532 PATA CompactFlash support" depends on MIKROTIK_RB532 help This option enables support for the RouterBoard 532 PATA CompactFlash controller. If unsure, say N. config PATA_RZ1000 tristate "PC Tech RZ1000 PATA support" depends on PCI help This option enables basic support for the PC Tech RZ1000/1 PATA controllers via the new ATA layer If unsure, say N. config PATA_SAMSUNG_CF tristate "Samsung SoC PATA support" depends on SAMSUNG_DEV_IDE help This option enables basic support for Samsung's S3C/S5P board PATA controllers via the new ATA layer If unsure, say N. config PATA_WINBOND_VLB tristate "Winbond W83759A VLB PATA support (Experimental)" depends on ISA select PATA_LEGACY help Support for the Winbond W83759A controller on Vesa Local Bus systems. comment "Generic fallback / legacy drivers" config PATA_ACPI tristate "ACPI firmware driver for PATA" depends on ATA_ACPI && ATA_BMDMA help This option enables an ACPI method driver which drives motherboard PATA controller interfaces through the ACPI firmware in the BIOS. This driver can sometimes handle otherwise unsupported hardware. config ATA_GENERIC tristate "Generic ATA support" depends on PCI && ATA_BMDMA help This option enables support for generic BIOS configured ATA controllers via the new ATA layer If unsure, say N. config PATA_LEGACY tristate "Legacy ISA PATA support (Experimental)" depends on (ISA || PCI) help This option enables support for ISA/VLB/PCI bus legacy PATA ports and allows them to be accessed via the new ATA layer. If unsure, say N. endif # ATA_SFF endif # ATA