#include #include #include "internal.h" int lan78xx_dump_regs(struct ethtool_drvinfo *info, struct ethtool_regs *regs) { unsigned int *lan78xx_reg = (unsigned int *)regs->data; fprintf(stdout, "LAN78xx Registers:\n"); fprintf(stdout, "------------------\n"); fprintf(stdout, "ID_REV = 0x%08X\n", *lan78xx_reg++); fprintf(stdout, "INT_STS = 0x%08X\n", *lan78xx_reg++); fprintf(stdout, "HW_CFG = 0x%08X\n", *lan78xx_reg++); fprintf(stdout, "PMT_CTRL = 0x%08X\n", *lan78xx_reg++); fprintf(stdout, "E2P_CMD = 0x%08X\n", *lan78xx_reg++); fprintf(stdout, "E2P_DATA = 0x%08X\n", *lan78xx_reg++); fprintf(stdout, "USB_STATUS = 0x%08X\n", *lan78xx_reg++); fprintf(stdout, "VLAN_TYPE = 0x%08X\n", *lan78xx_reg++); fprintf(stdout, "\n"); fprintf(stdout, "MAC Registers:\n"); fprintf(stdout, "--------------\n"); fprintf(stdout, "MAC_CR = 0x%08X\n", *lan78xx_reg++); fprintf(stdout, "MAC_RX = 0x%08X\n", *lan78xx_reg++); fprintf(stdout, "MAC_TX = 0x%08X\n", *lan78xx_reg++); fprintf(stdout, "FLOW = 0x%08X\n", *lan78xx_reg++); fprintf(stdout, "ERR_STS = 0x%08X\n", *lan78xx_reg++); fprintf(stdout, "MII_ACC = 0x%08X\n", *lan78xx_reg++); fprintf(stdout, "MII_DATA = 0x%08X\n", *lan78xx_reg++); fprintf(stdout, "EEE_TX_LPI_REQ_DLY = 0x%08X\n", *lan78xx_reg++); fprintf(stdout, "EEE_TW_TX_SYS = 0x%08X\n", *lan78xx_reg++); fprintf(stdout, "EEE_TX_LPI_REM_DLY = 0x%08X\n", *lan78xx_reg++); fprintf(stdout, "WUCSR = 0x%08X\n", *lan78xx_reg++); fprintf(stdout, "\n"); fprintf(stdout, "PHY Registers:\n"); fprintf(stdout, "--------------\n"); fprintf(stdout, "Mode Control = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "Mode Status = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "Device identifier1 = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "Device identifier2 = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "Auto-Neg Advertisement = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "Auto-Neg Link Partner Ability = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "Auto-Neg Expansion = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "Auto-Neg Next Page TX = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "Auto-Neg Link Partner Next Page RX = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "1000BASE-T Control = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "1000BASE-T Status = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "Reserved = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "Reserved = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "MMD Access Control = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "MMD Access Address/Data = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "1000BASE-T Status Extension1 = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "1000BASE-TX Status Extension = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "1000BASE-T Status Extension2 = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "Bypass Control = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "100BASE-TX/1000BASE-T Rx Error Counter = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "100BASE-TX/1000BASE-T FC Err Counter = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "10BASE-T/100BASE-TX/1000BASE-T LD Counter = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "Extended 10BASE-T Control and Status = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "Extended PHY Control1 = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "Extended PHY Control2 = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "Interrupt Mask = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "Interrupt Status = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "Reserved = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "Auxiliary Control and Status = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "LED Mode Select = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "LED Behavior = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "Extended Page Access = 0x%04X\n", *lan78xx_reg++); fprintf(stdout, "\n"); return 0; }