# # Coresight configuration # menuconfig CORESIGHT bool "CoreSight Tracing Support" select ARM_AMBA help This framework provides a kernel interface for the CoreSight debug and trace drivers to register themselves with. It's intended to build a topological view of the CoreSight components based on a DT specification and configure the right serie of components when a trace source gets enabled. if CORESIGHT config CORESIGHT_EVENT tristate "CoreSight Event driver" depends on TRACEPOINTS help This driver provides support for registering with various events and performing CoreSight actions like aborting trace on their occurrence. These events can be controlled by using module parameters. config CORESIGHT_CSR bool "CoreSight Slave Register driver" help This driver provides support for CoreSight Slave Register block that hosts miscellaneous configuration registers. Those configuration registers can be used to control, various coresight configurations. config CORESIGHT_LINKS_AND_SINKS bool "CoreSight Link and Sink drivers" help This enables support for CoreSight link and sink drivers that are responsible for transporting and collecting the trace data respectively. Link and sinks are dynamically aggregated with a trace entity at run time to form a complete trace path. config CORESIGHT_LINK_AND_SINK_TMC bool "Coresight generic TMC driver" depends on CORESIGHT_LINKS_AND_SINKS select CORESIGHT_CSR help This enables support for the Trace Memory Controller driver. Depending on its configuration the device can act as a link (embedded trace router - ETR) or sink (embedded trace FIFO). The driver complies with the generic implementation of the component without special enhancement or added features. config CORESIGHT_SINK_TPIU bool "Coresight generic TPIU driver" depends on CORESIGHT_LINKS_AND_SINKS help This enables support for the Trace Port Interface Unit driver, responsible for bridging the gap between the on-chip coresight components and a trace for bridging the gap between the on-chip coresight components and a trace port collection engine, typically connected to an external host for use case capturing more traces than the on-board coresight memory can handle. config CORESIGHT_SINK_ETBV10 bool "Coresight ETBv1.0 driver" depends on CORESIGHT_LINKS_AND_SINKS help This enables support for the Embedded Trace Buffer version 1.0 driver that complies with the generic implementation of the component without special enhancement or added features. config CORESIGHT_SOURCE_ETM3X bool "CoreSight Embedded Trace Macrocell 3.x driver" depends on !ARM64 select CORESIGHT_LINKS_AND_SINKS help This driver provides support for processor ETM3.x and PTM1.x modules, which allows tracing the instructions that a processor is executing This is primarily useful for instruction level tracing. Depending the ETM version data tracing may also be available. config CORESIGHT_SOURCE_ETM4X bool "CoreSight Embedded Trace Macrocell 4.x driver" select CORESIGHT_LINKS_AND_SINKS help This driver provides support for the ETM4.x tracer module, tracing the instructions that a processor is executing. This is primarily useful for instruction level tracing. Depending on the implemented version data tracing may also be available. config CORESIGHT_REMOTE_ETM bool "Remote processor ETM trace support" depends on MSM_QMI_INTERFACE help Enables support for ETM trace collection on remote processor using CoreSight framework. Enabling this will allow turning on ETM tracing on remote processor via sysfs by configuring the required CoreSight components. config CORESIGHT_REMOTE_ETM_DEFAULT_ENABLE int "default enable bits for Remote processor ETM" depends on CORESIGHT_REMOTE_ETM help Support for enabling separated Remote processor ETM tracing. Depends on if instance id bit is set. config CORESIGHT_QCOM_REPLICATOR bool "Qualcomm CoreSight Replicator driver" depends on CORESIGHT_LINKS_AND_SINKS help This enables support for Qualcomm CoreSight link driver. The programmable ATB replicator sends the ATB trace stream from the ETB/ETF to the TPIUi and ETR. config CORESIGHT_STM bool "CoreSight System Trace Macrocell driver" select CORESIGHT_LINKS_AND_SINKS help This driver provides support for hardware assisted software instrumentation based tracing. This is primarily useful for logging useful software events or data. config CORESIGHT_HWEVENT bool "CoreSight Hardware Event driver" depends on CORESIGHT_STM select CORESIGHT_CSR help This driver provides support for monitoring and tracing CoreSight Hardware Event across STM interface. It configures Coresight Hardware Event mux control registers to select hardware events based on user input. config CORESIGHT_CTI bool "CoreSight Cross Trigger Interface driver" help This driver provides support for Cross Trigger Interface that is used to input or output i.e. pass cross trigger events from one hardware component to another. It can also be used to pass software generated events. config CORESIGHT_TPDA bool "CoreSight Trace, Profiling & Diagnostics Aggregator driver" help This driver provides support for configuring aggregator. This is primarily useful for pulling the data sets from one or more attached monitors and pushing the resultant data out. Multiple monitors are connected on different input ports of TPDA. config CORESIGHT_TPDM bool "CoreSight Trace, Profiling & Diagnostics Monitor driver" help This driver provides support for configuring monitor. Monitors are primarily responsible for data set collection and support the ability to collect any permutation of data set types. Monitors are also responsible for interaction with system cross triggering. config CORESIGHT_TPDM_DEFAULT_ENABLE bool "Turn on TPDM tracing by default" depends on CORESIGHT_TPDM help Turns on CoreSight TPDM tracing for different data set types by default. Otherwise, tracing is disabled by default but can be enabled via sysfs. If unsure, say 'N' here to avoid potential power and performance penalty. config CORESIGHT_QPDI bool "CoreSight PMIC debug interface support" help This driver provides support for controlling the PMIC debug interface feature. When enabled via sysfs it allows disagnostic access to the PMIC. Similarly this debug feature can be disabled via sysfs which prevents debug dongle detection. config CORESIGHT_SOURCE_DUMMY bool "Dummy source support" help Enables support for dummy source devices. Dummy source driver can be used for CoreSight sources that are owned and configured by some other subsystem and use Linux drivers to configure rest of trace path. endif