# # IPv6 configuration # # IPv6 as module will cause a CRASH if you try to unload it menuconfig IPV6 tristate "The IPv6 protocol" default m ---help--- This is complemental support for the IP version 6. You will still be able to do traditional IPv4 networking as well. For general information about IPv6, see . For Linux IPv6 development information, see . For specific information about IPv6 under Linux, read the HOWTO at . To compile this protocol support as a module, choose M here: the module will be called ipv6. if IPV6 config IPV6_PRIVACY bool "IPv6: Privacy Extensions support" ---help--- Privacy Extensions for Stateless Address Autoconfiguration in IPv6 support. With this option, additional periodically-alter pseudo-random global-scope unicast address(es) will assigned to your interface(s). We use our standard pseudo random algorithm to generate randomized interface identifier, instead of one described in RFC 3041. By default, kernel do not generate temporary addresses. To use temporary addresses, do echo 2 >/proc/sys/net/ipv6/conf/all/use_tempaddr See for details. config IPV6_ROUTER_PREF bool "IPv6: Router Preference (RFC 4191) support" ---help--- Router Preference is an optional extension to the Router Advertisement message to improve the ability of hosts to pick more appropriate router, especially when the hosts is placed in a multi-homed network. If unsure, say N. config IPV6_ROUTE_INFO bool "IPv6: Route Information (RFC 4191) support (EXPERIMENTAL)" depends on IPV6_ROUTER_PREF && EXPERIMENTAL ---help--- This is experimental support of Route Information. If unsure, say N. config IPV6_OPTIMISTIC_DAD bool "IPv6: Enable RFC 4429 Optimistic DAD (EXPERIMENTAL)" depends on EXPERIMENTAL ---help--- This is experimental support for optimistic Duplicate Address Detection. It allows for autoconfigured addresses to be used more quickly. If unsure, say N. config INET6_AH tristate "IPv6: AH transformation" select XFRM select CRYPTO select CRYPTO_HMAC select CRYPTO_MD5 select CRYPTO_SHA1 ---help--- Support for IPsec AH. If unsure, say Y. config INET6_ESP tristate "IPv6: ESP transformation" select XFRM select CRYPTO select CRYPTO_AUTHENC select CRYPTO_HMAC select CRYPTO_MD5 select CRYPTO_CBC select CRYPTO_SHA1 select CRYPTO_DES ---help--- Support for IPsec ESP. If unsure, say Y. config INET6_IPCOMP tristate "IPv6: IPComp transformation" select INET6_XFRM_TUNNEL select XFRM_IPCOMP ---help--- Support for IP Payload Compression Protocol (IPComp) (RFC3173), typically needed for IPsec. If unsure, say Y. config IPV6_MIP6 tristate "IPv6: Mobility (EXPERIMENTAL)" depends on EXPERIMENTAL select XFRM ---help--- Support for IPv6 Mobility described in RFC 3775. If unsure, say N. config INET6_XFRM_TUNNEL tristate select INET6_TUNNEL default n config INET6_TUNNEL tristate default n config INET6_XFRM_MODE_TRANSPORT tristate "IPv6: IPsec transport mode" default IPV6 select XFRM ---help--- Support for IPsec transport mode. If unsure, say Y. config INET6_XFRM_MODE_TUNNEL tristate "IPv6: IPsec tunnel mode" default IPV6 select XFRM ---help--- Support for IPsec tunnel mode. If unsure, say Y. config INET6_XFRM_MODE_BEET tristate "IPv6: IPsec BEET mode" default IPV6 select XFRM ---help--- Support for IPsec BEET mode. If unsure, say Y. config INET6_XFRM_MODE_ROUTEOPTIMIZATION tristate "IPv6: MIPv6 route optimization mode (EXPERIMENTAL)" depends on EXPERIMENTAL select XFRM ---help--- Support for MIPv6 route optimization mode. config IPV6_SIT tristate "IPv6: IPv6-in-IPv4 tunnel (SIT driver)" select INET_TUNNEL select IPV6_NDISC_NODETYPE default y ---help--- Tunneling means encapsulating data of one protocol type within another protocol and sending it over a channel that understands the encapsulating protocol. This driver implements encapsulation of IPv6 into IPv4 packets. This is useful if you want to connect two IPv6 networks over an IPv4-only path. Saying M here will produce a module called sit.ko. If unsure, say Y. config IPV6_NDISC_NODETYPE bool config IPV6_TUNNEL tristate "IPv6: IP-in-IPv6 tunnel (RFC2473)" select INET6_TUNNEL ---help--- Support for IPv6-in-IPv6 and IPv4-in-IPv6 tunnels described in RFC 2473. If unsure, say N. config IPV6_MULTIPLE_TABLES bool "IPv6: Multiple Routing Tables" depends on EXPERIMENTAL select FIB_RULES ---help--- Support multiple routing tables. config IPV6_SUBTREES bool "IPv6: source address based routing" depends on IPV6_MULTIPLE_TABLES ---help--- Enable routing by source address or prefix. The destination address is still the primary routing key, so mixing normal and source prefix specific routes in the same routing table may sometimes lead to unintended routing behavior. This can be avoided by defining different routing tables for the normal and source prefix specific routes. If unsure, say N. if LANTIQ #IFX plaform specific source "net/ipv6/Kconfig.ifx" endif config IPV6_MROUTE bool "IPv6: multicast routing (EXPERIMENTAL)" depends on IPV6 && EXPERIMENTAL ---help--- Experimental support for IPv6 multicast forwarding. If unsure, say N. config IPV6_PIMSM_V2 bool "IPv6: PIM-SM version 2 support (EXPERIMENTAL)" depends on IPV6_MROUTE ---help--- Support for IPv6 PIM multicast routing protocol PIM-SMv2. If unsure, say N. endif # IPV6