--- zzzz-none-000/linux-2.6.28.10/drivers/usb/musb/tusb6010.h	2009-05-02 18:54:43.000000000 +0000
+++ puma5-6360-529/linux-2.6.28.10/drivers/usb/musb/tusb6010.h	2010-03-30 18:41:51.000000000 +0000
@@ -230,4 +230,173 @@
 #define TUSB_REV_30	0x30
 #define TUSB_REV_31	0x31
 
+/*----------------------------------------------------------------------------*/
+
+#ifdef CONFIG_USB_TUSB6010
+
+/* configuration parameters specific to this silicon */
+
+/* Number of Tx endpoints. Legal values are 1 - 16 (this value includes EP0) */
+#define MUSB_C_NUM_EPT 16
+
+/* Number of Rx endpoints. Legal values are 1 - 16 (this value includes EP0) */
+#define MUSB_C_NUM_EPR 16
+
+/* Endpoint 1 to 15 direction types. C_EP1_DEF is defined if either Tx endpoint
+ * 1 or Rx endpoint 1 are used.
+ */
+#define MUSB_C_EP1_DEF
+
+/* C_EP1_TX_DEF is defined if Tx endpoint 1 is used */
+#define MUSB_C_EP1_TX_DEF
+
+/* C_EP1_RX_DEF is defined if Rx endpoint 1 is used */
+#define MUSB_C_EP1_RX_DEF
+
+/* C_EP1_TOR_DEF is defined if Tx endpoint 1 and Rx endpoint 1 share a FIFO */
+/* #define C_EP1_TOR_DEF */
+
+/* C_EP1_TAR_DEF is defined if both Tx endpoint 1 and Rx endpoint 1 are used
+ * and do not share a FIFO.
+ */
+#define MUSB_C_EP1_TAR_DEF
+
+/* Similarly for all other used endpoints */
+#define MUSB_C_EP2_DEF
+#define MUSB_C_EP2_TX_DEF
+#define MUSB_C_EP2_RX_DEF
+#define MUSB_C_EP2_TAR_DEF
+#define MUSB_C_EP3_DEF
+#define MUSB_C_EP3_TX_DEF
+#define MUSB_C_EP3_RX_DEF
+#define MUSB_C_EP3_TAR_DEF
+#define MUSB_C_EP4_DEF
+#define MUSB_C_EP4_TX_DEF
+#define MUSB_C_EP4_RX_DEF
+#define MUSB_C_EP4_TAR_DEF
+
+/* Endpoint 1 to 15 FIFO address bits. Legal values are 3 to 13 - corresponding
+ * to FIFO sizes of 8 to 8192 bytes. If an Tx endpoint shares a FIFO with an Rx
+ * endpoint then the Rx FIFO size must be the same as the Tx FIFO size. All
+ * endpoints 1 to 15 must be defined, unused endpoints should be set to 2.
+ */
+#define MUSB_C_EP1T_BITS 5
+#define MUSB_C_EP1R_BITS 5
+#define MUSB_C_EP2T_BITS 5
+#define MUSB_C_EP2R_BITS 5
+#define MUSB_C_EP3T_BITS 3
+#define MUSB_C_EP3R_BITS 3
+#define MUSB_C_EP4T_BITS 3
+#define MUSB_C_EP4R_BITS 3
+
+#define MUSB_C_EP5T_BITS 2
+#define MUSB_C_EP5R_BITS 2
+#define MUSB_C_EP6T_BITS 2
+#define MUSB_C_EP6R_BITS 2
+#define MUSB_C_EP7T_BITS 2
+#define MUSB_C_EP7R_BITS 2
+#define MUSB_C_EP8T_BITS 2
+#define MUSB_C_EP8R_BITS 2
+#define MUSB_C_EP9T_BITS 2
+#define MUSB_C_EP9R_BITS 2
+#define MUSB_C_EP10T_BITS 2
+#define MUSB_C_EP10R_BITS 2
+#define MUSB_C_EP11T_BITS 2
+#define MUSB_C_EP11R_BITS 2
+#define MUSB_C_EP12T_BITS 2
+#define MUSB_C_EP12R_BITS 2
+#define MUSB_C_EP13T_BITS 2
+#define MUSB_C_EP13R_BITS 2
+#define MUSB_C_EP14T_BITS 2
+#define MUSB_C_EP14R_BITS 2
+#define MUSB_C_EP15T_BITS 2
+#define MUSB_C_EP15R_BITS 2
+
+/* Define the following constant if the USB2.0 Transceiver Macrocell data width
+ * is 16-bits.
+ */
+/* #define C_UTM_16 */
+
+/* Define this constant if the CPU uses big-endian byte ordering. */
+/* #define C_BIGEND */
+
+/* Define the following constant if any Tx endpoint is required to support
+ * multiple bulk packets.
+ */
+/* #define C_MP_TX */
+
+/* Define the following constant if any Rx endpoint is required to support
+ * multiple bulk packets.
+ */
+/* #define C_MP_RX */
+
+/* Define the following constant if any Tx endpoint is required to support high
+ * bandwidth ISO.
+ */
+/* #define C_HB_TX */
+
+/* Define the following constant if any Rx endpoint is required to support high
+ * bandwidth ISO.
+ */
+/* #define C_HB_RX */
+
+/* Define the following constant if software connect/disconnect control is
+ * required.
+ */
+#define MUSB_C_SOFT_CON
+
+/* Define the following constant if Vendor Control Registers are required. */
+/* #define C_VEND_REG */
+
+/* Vendor control register widths. */
+#define MUSB_C_VCTL_BITS 4
+#define MUSB_C_VSTAT_BITS 8
+
+/* Define the following constant to include a DMA controller. */
+/* #define C_DMA */
+
+/* Define the following constant if 2 or more DMA channels are required. */
+/* #define C_DMA2 */
+
+/* Define the following constant if 3 or more DMA channels are required. */
+/* #define C_DMA3 */
+
+/* Define the following constant if 4 or more DMA channels are required. */
+/* #define C_DMA4 */
+
+/* Define the following constant if 5 or more DMA channels are required. */
+/* #define C_DMA5 */
+
+/* Define the following constant if 6 or more DMA channels are required. */
+/* #define C_DMA6 */
+
+/* Define the following constant if 7 or more DMA channels are required. */
+/* #define C_DMA7 */
+
+/* Define the following constant if 8 or more DMA channels are required. */
+/* #define C_DMA8 */
+
+/* Enable Dynamic FIFO Sizing */
+#define MUSB_C_DYNFIFO_DEF
+
+/* Derived constants. The following constants are derived from the previous
+ * configuration constants
+ */
+
+/* Total number of endpoints. Legal values are 2 - 16. This must be equal to
+ * the larger of C_NUM_EPT, C_NUM_EPR
+ */
+/* #define MUSB_C_NUM_EPS 5 */
+
+/* C_EPMAX_BITS is equal to the largest endpoint FIFO word address bits */
+#define MUSB_C_EPMAX_BITS 11
+
+/* C_RAM_BITS is the number of address bits required to address the RAM (32-bit
+ * addresses).  It is defined as log2 of the sum of 2** of all the endpoint FIFO
+ * dword address bits (rounded up).
+ */
+#define MUSB_C_RAM_BITS 12
+
+#endif /* CONFIG_USB_TUSB6010 */
+
 #endif /* __TUSB6010_H__ */