# # Multifunction miscellaneous devices # menuconfig MFD_SUPPORT bool "Multifunction device drivers" depends on HAS_IOMEM default y help Multifunction devices embed several functions (e.g. GPIOs, touchscreens, keyboards, current regulators, power management chips, etc...) in one single integrated circuit. They usually talk to the main CPU through one or more IRQ lines and low speed data busses (SPI, I2C, etc..). They appear as one single device to the main system through the data bus and the MFD framework allows for sub devices (a.k.a. functions) to appear as discrete platform devices. MFDs are typically found on embedded platforms. This option alone does not add any kernel code. if MFD_SUPPORT config MFD_CORE tristate default n config MFD_88PM860X bool "Support Marvell 88PM8606/88PM8607" depends on I2C=y && GENERIC_HARDIRQS select MFD_CORE help This supports for Marvell 88PM8606/88PM8607 Power Management IC. This includes the I2C driver and the core APIs _only_, you have to select individual components like voltage regulators, RTC and battery-charger under the corresponding menus. config MFD_SM501 tristate "Support for Silicon Motion SM501" ---help--- This is the core driver for the Silicon Motion SM501 multimedia companion chip. This device is a multifunction device which may provide numerous interfaces including USB host controller, USB gadget, asynchronous serial ports, audio functions, and a dual display video interface. The device may be connected by PCI or local bus with varying functions enabled. config MFD_SM501_GPIO bool "Export GPIO via GPIO layer" depends on MFD_SM501 && GPIOLIB ---help--- This option uses the gpio library layer to export the 64 GPIO lines on the SM501. The platform data is used to supply the base number for the first GPIO line to register. config MFD_ASIC3 bool "Support for Compaq ASIC3" depends on GENERIC_HARDIRQS && GPIOLIB && ARM select MFD_CORE ---help--- This driver supports the ASIC3 multifunction chip found on many PDAs (mainly iPAQ and HTC based ones) config MFD_DAVINCI_VOICECODEC tristate select MFD_CORE config MFD_DM355EVM_MSP bool "DaVinci DM355 EVM microcontroller" depends on I2C=y && MACH_DAVINCI_DM355_EVM help This driver supports the MSP430 microcontroller used on these boards. MSP430 firmware manages resets and power sequencing, inputs from buttons and the IR remote, LEDs, an RTC, and more. config MFD_TI_SSP tristate "TI Sequencer Serial Port support" depends on ARCH_DAVINCI_TNETV107X select MFD_CORE ---help--- Say Y here if you want support for the Sequencer Serial Port in a Texas Instruments TNETV107X SoC. To compile this driver as a module, choose M here: the module will be called ti-ssp. config HTC_EGPIO bool "HTC EGPIO support" depends on GENERIC_HARDIRQS && GPIOLIB && ARM help This driver supports the CPLD egpio chip present on several HTC phones. It provides basic support for input pins, output pins, and irqs. config HTC_PASIC3 tristate "HTC PASIC3 LED/DS1WM chip support" select MFD_CORE help This core driver provides register access for the LED/DS1WM chips labeled "AIC2" and "AIC3", found on HTC Blueangel and HTC Magician devices, respectively. Actual functionality is handled by the leds-pasic3 and ds1wm drivers. config HTC_I2CPLD bool "HTC I2C PLD chip support" depends on I2C=y && GPIOLIB help If you say yes here you get support for the supposed CPLD found on omap850 HTC devices like the HTC Wizard and HTC Herald. This device provides input and output GPIOs through an I2C interface to one or more sub-chips. config UCB1400_CORE tristate "Philips UCB1400 Core driver" depends on AC97_BUS depends on GPIOLIB help This enables support for the Philips UCB1400 core functions. The UCB1400 is an AC97 audio codec. To compile this driver as a module, choose M here: the module will be called ucb1400_core. config TPS6105X tristate "TPS61050/61052 Boost Converters" depends on I2C select REGULATOR select MFD_CORE select REGULATOR_FIXED_VOLTAGE help This option enables a driver for the TP61050/TPS61052 high-power "white LED driver". This boost converter is sometimes used for other things than white LEDs, and also contains a GPIO pin. config TPS65010 tristate "TPS6501x Power Management chips" depends on I2C && GPIOLIB default y if MACH_OMAP_H2 || MACH_OMAP_H3 || MACH_OMAP_OSK help If you say yes here you get support for the TPS6501x series of Power Management chips. These include voltage regulators, lithium ion/polymer battery charging, and other features that are often used in portable devices like cell phones and cameras. This driver can also be built as a module. If so, the module will be called tps65010. config TPS6507X tristate "TPS6507x Power Management / Touch Screen chips" select MFD_CORE depends on I2C help If you say yes here you get support for the TPS6507x series of Power Management / Touch Screen chips. These include voltage regulators, lithium ion/polymer battery charging, touch screen and other features that are often used in portable devices. This driver can also be built as a module. If so, the module will be called tps6507x. config MENELAUS bool "Texas Instruments TWL92330/Menelaus PM chip" depends on I2C=y && ARCH_OMAP2 help If you say yes here you get support for the Texas Instruments TWL92330/Menelaus Power Management chip. This include voltage regulators, Dual slot memory card transceivers, real-time clock and other features that are often used in portable devices like cell phones and PDAs. config TWL4030_CORE bool "Texas Instruments TWL4030/TWL5030/TWL6030/TPS659x0 Support" depends on I2C=y && GENERIC_HARDIRQS help Say yes here if you have TWL4030 / TWL6030 family chip on your board. This core driver provides register access and IRQ handling facilities, and registers devices for the various functions so that function-specific drivers can bind to them. These multi-function chips are found on many OMAP2 and OMAP3 boards, providing power management, RTC, GPIO, keypad, a high speed USB OTG transceiver, an audio codec (on most versions) and many other features. config TWL4030_MADC tristate "Texas Instruments TWL4030 MADC" depends on TWL4030_CORE help This driver provides support for triton TWL4030-MADC. The driver supports both RT and SW conversion methods. This driver can be built as a module. If so it will be named twl4030-madc config TWL4030_POWER bool "Support power resources on TWL4030 family chips" depends on TWL4030_CORE && ARM help Say yes here if you want to use the power resources on the TWL4030 family chips. Most of these resources are regulators, which have a separate driver; some are control signals, such as clock request handshaking. This driver uses board-specific data to initialize the resources and load scripts controlling which resources are switched off/on or reset when a sleep, wakeup or warm reset event occurs. config TWL4030_CODEC bool depends on TWL4030_CORE select MFD_CORE default n config TWL6030_PWM tristate "TWL6030 PWM (Pulse Width Modulator) Support" depends on TWL4030_CORE select HAVE_PWM default n help Say yes here if you want support for TWL6030 PWM. This is used to control charging LED brightness. config MFD_STMPE bool "Support STMicroelectronics STMPE" depends on I2C=y && GENERIC_HARDIRQS select MFD_CORE help Support for the STMPE family of I/O Expanders from STMicroelectronics. Currently supported devices are: STMPE811: GPIO, Touchscreen STMPE1601: GPIO, Keypad STMPE2401: GPIO, Keypad STMPE2403: GPIO, Keypad This driver provides common support for accessing the device, additional drivers must be enabled in order to use the functionality of the device. Currently available sub drivers are: GPIO: stmpe-gpio Keypad: stmpe-keypad Touchscreen: stmpe-ts config MFD_TC3589X bool "Support Toshiba TC35892 and variants" depends on I2C=y && GENERIC_HARDIRQS select MFD_CORE help Support for the Toshiba TC35892 and variants I/O Expander. This driver provides common support for accessing the device, additional drivers must be enabled in order to use the functionality of the device. config MFD_TMIO bool default n config MFD_T7L66XB bool "Support Toshiba T7L66XB" depends on ARM && HAVE_CLK select MFD_CORE select MFD_TMIO help Support for Toshiba Mobile IO Controller T7L66XB config MFD_TC6387XB bool "Support Toshiba TC6387XB" depends on ARM && HAVE_CLK select MFD_CORE select MFD_TMIO help Support for Toshiba Mobile IO Controller TC6387XB config MFD_TC6393XB bool "Support Toshiba TC6393XB" depends on GPIOLIB && ARM select MFD_CORE select MFD_TMIO help Support for Toshiba Mobile IO Controller TC6393XB config PMIC_DA903X bool "Dialog Semiconductor DA9030/DA9034 PMIC Support" depends on I2C=y help Say yes here to support for Dialog Semiconductor DA9030 (a.k.a ARAVA) and DA9034 (a.k.a MICCO), these are Power Management IC usually found on PXA processors-based platforms. This includes the I2C driver and the core APIs _only_, you have to select individual components like LCD backlight, voltage regulators, LEDs and battery-charger under the corresponding menus. config PMIC_ADP5520 bool "Analog Devices ADP5520/01 MFD PMIC Core Support" depends on I2C=y help Say yes here to add support for Analog Devices AD5520 and ADP5501, Multifunction Power Management IC. This includes the I2C driver and the core APIs _only_, you have to select individual components like LCD backlight, LEDs, GPIOs and Kepad under the corresponding menus. config MFD_MAX8925 bool "Maxim Semiconductor MAX8925 PMIC Support" depends on I2C=y && GENERIC_HARDIRQS select MFD_CORE help Say yes here to support for Maxim Semiconductor MAX8925. This is a Power Management IC. This driver provies common support for accessing the device, additional drivers must be enabled in order to use the functionality of the device. config MFD_MAX8997 bool "Maxim Semiconductor MAX8997/8966 PMIC Support" depends on I2C=y && GENERIC_HARDIRQS select MFD_CORE help Say yes here to support for Maxim Semiconductor MAX8998/8966. This is a Power Management IC with RTC, Flash, Fuel Gauge, Haptic, MUIC controls on chip. This driver provides common support for accessing the device; additional drivers must be enabled in order to use the functionality of the device. config MFD_MAX8998 bool "Maxim Semiconductor MAX8998/National LP3974 PMIC Support" depends on I2C=y && GENERIC_HARDIRQS select MFD_CORE help Say yes here to support for Maxim Semiconductor MAX8998 and National Semiconductor LP3974. This is a Power Management IC. This driver provies common support for accessing the device, additional drivers must be enabled in order to use the functionality of the device. config MFD_WM8400 tristate "Support Wolfson Microelectronics WM8400" select MFD_CORE depends on I2C help Support for the Wolfson Microelecronics WM8400 PMIC and audio CODEC. This driver provides common support for accessing the device, additional drivers must be enabled in order to use the functionality of the device. config MFD_WM831X bool depends on GENERIC_HARDIRQS config MFD_WM831X_I2C bool "Support Wolfson Microelectronics WM831x/2x PMICs with I2C" select MFD_CORE select MFD_WM831X depends on I2C=y && GENERIC_HARDIRQS help Support for the Wolfson Microelecronics WM831x and WM832x PMICs when controlled using I2C. This driver provides common support for accessing the device, additional drivers must be enabled in order to use the functionality of the device. config MFD_WM831X_SPI bool "Support Wolfson Microelectronics WM831x/2x PMICs with SPI" select MFD_CORE select MFD_WM831X depends on SPI_MASTER && GENERIC_HARDIRQS help Support for the Wolfson Microelecronics WM831x and WM832x PMICs when controlled using SPI. This driver provides common support for accessing the device, additional drivers must be enabled in order to use the functionality of the device. config MFD_WM8350 bool depends on GENERIC_HARDIRQS config MFD_WM8350_CONFIG_MODE_0 bool depends on MFD_WM8350 config MFD_WM8350_CONFIG_MODE_1 bool depends on MFD_WM8350 config MFD_WM8350_CONFIG_MODE_2 bool depends on MFD_WM8350 config MFD_WM8350_CONFIG_MODE_3 bool depends on MFD_WM8350 config MFD_WM8351_CONFIG_MODE_0 bool depends on MFD_WM8350 config MFD_WM8351_CONFIG_MODE_1 bool depends on MFD_WM8350 config MFD_WM8351_CONFIG_MODE_2 bool depends on MFD_WM8350 config MFD_WM8351_CONFIG_MODE_3 bool depends on MFD_WM8350 config MFD_WM8352_CONFIG_MODE_0 bool depends on MFD_WM8350 config MFD_WM8352_CONFIG_MODE_1 bool depends on MFD_WM8350 config MFD_WM8352_CONFIG_MODE_2 bool depends on MFD_WM8350 config MFD_WM8352_CONFIG_MODE_3 bool depends on MFD_WM8350 config MFD_WM8350_I2C bool "Support Wolfson Microelectronics WM8350 with I2C" select MFD_WM8350 depends on I2C=y && GENERIC_HARDIRQS help The WM8350 is an integrated audio and power management subsystem with watchdog and RTC functionality for embedded systems. This option enables core support for the WM8350 with I2C as the control interface. Additional options must be selected to enable support for the functionality of the chip. config MFD_WM8994 bool "Support Wolfson Microelectronics WM8994" select MFD_CORE depends on I2C=y && GENERIC_HARDIRQS help The WM8994 is a highly integrated hi-fi CODEC designed for smartphone applicatiosn. As well as audio functionality it has on board GPIO and regulator functionality which is supported via the relevant subsystems. This driver provides core support for the WM8994, in order to use the actual functionaltiy of the device other drivers must be enabled. config MFD_PCF50633 tristate "Support for NXP PCF50633" depends on I2C help Say yes here if you have NXP PCF50633 chip on your board. This core driver provides register access and IRQ handling facilities, and registers devices for the various functions so that function-specific drivers can bind to them. config MFD_MC13783 tristate config MFD_MC13XXX tristate "Support Freescale MC13783 and MC13892" depends on SPI_MASTER select MFD_CORE select MFD_MC13783 help Support for the Freescale (Atlas) PMIC and audio CODECs MC13783 and MC13892. This driver provides common support for accessing the device, additional drivers must be enabled in order to use the functionality of the device. config PCF50633_ADC tristate "Support for NXP PCF50633 ADC" depends on MFD_PCF50633 help Say yes here if you want to include support for ADC in the NXP PCF50633 chip. config PCF50633_GPIO tristate "Support for NXP PCF50633 GPIO" depends on MFD_PCF50633 help Say yes here if you want to include support GPIO for pins on the PCF50633 chip. config ABX500_CORE bool "ST-Ericsson ABX500 Mixed Signal Circuit register functions" default y if ARCH_U300 || ARCH_U8500 help Say yes here if you have the ABX500 Mixed Signal IC family chips. This core driver expose register access functions. Functionality specific drivers using these functions can remain unchanged when IC changes. Binding of the functions to actual register access is done by the IC core driver. config AB3100_CORE bool "ST-Ericsson AB3100 Mixed Signal Circuit core functions" depends on I2C=y && ABX500_CORE select MFD_CORE default y if ARCH_U300 help Select this to enable the AB3100 Mixed Signal IC core functionality. This connects to a AB3100 on the I2C bus and expose a number of symbols needed for dependent devices to read and write registers and subscribe to events from this multi-functional IC. This is needed to use other features of the AB3100 such as battery-backed RTC, charging control, LEDs, vibrator, system power and temperature, power management and ALSA sound. config AB3100_OTP tristate "ST-Ericsson AB3100 OTP functions" depends on AB3100_CORE default y if AB3100_CORE help Select this to enable the AB3100 Mixed Signal IC OTP (one-time programmable memory) support. This exposes a sysfs file to read out OTP values. config EZX_PCAP bool "PCAP Support" depends on GENERIC_HARDIRQS && SPI_MASTER help This enables the PCAP ASIC present on EZX Phones. This is needed for MMC, TouchScreen, Sound, USB, etc.. config AB8500_CORE bool "ST-Ericsson AB8500 Mixed Signal Power Management chip" depends on GENERIC_HARDIRQS && ABX500_CORE select MFD_CORE help Select this option to enable access to AB8500 power management chip. This connects to U8500 either on the SSP/SPI bus (deprecated since hardware version v1.0) or the I2C bus via PRCMU. It also adds the irq_chip parts for handling the Mixed Signal chip events. This chip embeds various other multimedia funtionalities as well. config AB8500_I2C_CORE bool "AB8500 register access via PRCMU I2C" depends on AB8500_CORE && UX500_SOC_DB8500 default y help This enables register access to the AB8500 chip via PRCMU I2C. The AB8500 chip can be accessed via SPI or I2C. On DB8500 hardware the I2C bus is connected to the Power Reset and Mangagement Unit, PRCMU. config AB8500_DEBUG bool "Enable debug info via debugfs" depends on AB8500_CORE && DEBUG_FS default y if DEBUG_FS help Select this option if you want debug information using the debug filesystem, debugfs. config AB8500_GPADC bool "AB8500 GPADC driver" depends on AB8500_CORE && REGULATOR_AB8500 default y help AB8500 GPADC driver used to convert Acc and battery/ac/usb voltage config AB3550_CORE bool "ST-Ericsson AB3550 Mixed Signal Circuit core functions" select MFD_CORE depends on I2C=y && GENERIC_HARDIRQS && ABX500_CORE help Select this to enable the AB3550 Mixed Signal IC core functionality. This connects to a AB3550 on the I2C bus and expose a number of symbols needed for dependent devices to read and write registers and subscribe to events from this multi-functional IC. This is needed to use other features of the AB3550 such as battery-backed RTC, charging control, LEDs, vibrator, system power and temperature, power management and ALSA sound. config MFD_CS5535 tristate "Support for CS5535 and CS5536 southbridge core functions" select MFD_CORE depends on PCI && X86 ---help--- This is the core driver for CS5535/CS5536 MFD functions. This is necessary for using the board's GPIO and MFGPT functionality. config MFD_TIMBERDALE tristate "Support for the Timberdale FPGA" select MFD_CORE depends on PCI && GPIOLIB ---help--- This is the core driver for the timberdale FPGA. This device is a multifunction device which exposes numerous platform devices. The timberdale FPGA can be found on the Intel Atom development board for in-vehicle infontainment, called Russellville. config LPC_SCH tristate "Intel SCH LPC" depends on PCI select MFD_CORE help LPC bridge function of the Intel SCH provides support for System Management Bus and General Purpose I/O. config MFD_RDC321X tristate "Support for RDC-R321x southbridge" select MFD_CORE depends on PCI help Say yes here if you want to have support for the RDC R-321x SoC southbridge which provides access to GPIOs and Watchdog using the southbridge PCI device configuration space. config MFD_JANZ_CMODIO tristate "Support for Janz CMOD-IO PCI MODULbus Carrier Board" select MFD_CORE depends on PCI help This is the core driver for the Janz CMOD-IO PCI MODULbus carrier board. This device is a PCI to MODULbus bridge which may host many different types of MODULbus daughterboards, including CAN and GPIO controllers. config MFD_JZ4740_ADC tristate "Support for the JZ4740 SoC ADC core" select MFD_CORE depends on MACH_JZ4740 help Say yes here if you want support for the ADC unit in the JZ4740 SoC. This driver is necessary for jz4740-battery and jz4740-hwmon driver. config MFD_TPS6586X bool "TPS6586x Power Management chips" depends on I2C=y && GPIOLIB && GENERIC_HARDIRQS select MFD_CORE help If you say yes here you get support for the TPS6586X series of Power Management chips. This driver provides common support for accessing the device, additional drivers must be enabled in order to use the functionality of the device. This driver can also be built as a module. If so, the module will be called tps6586x. config MFD_VX855 tristate "Support for VIA VX855/VX875 integrated south bridge" depends on PCI select MFD_CORE help Say yes here to enable support for various functions of the VIA VX855/VX875 south bridge. You will need to enable the vx855_spi and/or vx855_gpio drivers for this to do anything useful. config MFD_WL1273_CORE tristate "Support for TI WL1273 FM radio." depends on I2C select MFD_CORE default n help This is the core driver for the TI WL1273 FM radio. This MFD driver connects the radio-wl1273 V4L2 module and the wl1273 audio codec. config MFD_OMAP_USB_HOST bool "Support OMAP USBHS core driver" depends on USB_EHCI_HCD_OMAP || USB_OHCI_HCD_OMAP3 default y help This is the core driver for the OAMP EHCI and OHCI drivers. This MFD driver does the required setup functionalities for OMAP USB Host drivers. endif # MFD_SUPPORT menu "Multimedia Capabilities Port drivers" depends on ARCH_SA1100 config MCP tristate # Interface drivers config MCP_SA11X0 tristate "Support SA11x0 MCP interface" depends on ARCH_SA1100 select MCP # Chip drivers config MCP_UCB1200 tristate "Support for UCB1200 / UCB1300" depends on MCP config MCP_UCB1200_TS tristate "Touchscreen interface support" depends on MCP_UCB1200 && INPUT endmenu