// SPDX-License-Identifier: GPL-2.0-or-later /* * Access SD/MMC cards through SPI master controllers * * (C) Copyright 2005, Intec Automation, * Mike Lavender (mike@steroidmicros) * (C) Copyright 2006-2007, David Brownell * (C) Copyright 2007, Axis Communications, * Hans-Peter Nilsson (hp@axis.com) * (C) Copyright 2007, ATRON electronic GmbH, * Jan Nikitenko */ #include #include #include #include #include #include #include #include #include #include #include /* for R1_SPI_* bit values */ #include #include #include #include /* NOTES: * * - For now, we won't try to interoperate with a real mmc/sd/sdio * controller, although some of them do have hardware support for * SPI protocol. The main reason for such configs would be mmc-ish * cards like DataFlash, which don't support that "native" protocol. * * We don't have a "DataFlash/MMC/SD/SDIO card slot" abstraction to * switch between driver stacks, and in any case if "native" mode * is available, it will be faster and hence preferable. * * - MMC depends on a different chipselect management policy than the * SPI interface currently supports for shared bus segments: it needs * to issue multiple spi_message requests with the chipselect active, * using the results of one message to decide the next one to issue. * * Pending updates to the programming interface, this driver expects * that it not share the bus with other drivers (precluding conflicts). * * - We tell the controller to keep the chipselect active from the * beginning of an mmc_host_ops.request until the end. So beware * of SPI controller drivers that mis-handle the cs_change flag! * * However, many cards seem OK with chipselect flapping up/down * during that time ... at least on unshared bus segments. */ /* * Local protocol constants, internal to data block protocols. */ /* Response tokens used to ack each block written: */ #define SPI_MMC_RESPONSE_CODE(x) ((x) & 0x1f) #define SPI_RESPONSE_ACCEPTED ((2 << 1)|1) #define SPI_RESPONSE_CRC_ERR ((5 << 1)|1) #define SPI_RESPONSE_WRITE_ERR ((6 << 1)|1) /* Read and write blocks start with these tokens and end with crc; * on error, read tokens act like a subset of R2_SPI_* values. */ #define SPI_TOKEN_SINGLE 0xfe /* single block r/w, multiblock read */ #define SPI_TOKEN_MULTI_WRITE 0xfc /* multiblock write */ #define SPI_TOKEN_STOP_TRAN 0xfd /* terminate multiblock write */ #define MMC_SPI_BLOCKSIZE 512 #define MMC_SPI_R1B_TIMEOUT_MS 3000 #define MMC_SPI_INIT_TIMEOUT_MS 3000 /* One of the critical speed parameters is the amount of data which may * be transferred in one command. If this value is too low, the SD card * controller has to do multiple partial block writes (argggh!). With * today (2008) SD cards there is little speed gain if we transfer more * than 64 KBytes at a time. So use this value until there is any indication * that we should do more here. */ #define MMC_SPI_BLOCKSATONCE 128 /****************************************************************************/ /* * Local Data Structures */ /* "scratch" is per-{command,block} data exchanged with the card */ struct scratch { u8 status[29]; u8 data_token; __be16 crc_val; }; struct mmc_spi_host { struct mmc_host *mmc; struct spi_device *spi; unsigned char power_mode; u16 powerup_msecs; struct mmc_spi_platform_data *pdata; /* for bulk data transfers */ struct spi_transfer token, t, crc, early_status; struct spi_message m; /* for status readback */ struct spi_transfer status; struct spi_message readback; /* buffer used for commands and for message "overhead" */ struct scratch *data; /* Specs say to write ones most of the time, even when the card * has no need to read its input data; and many cards won't care. * This is our source of those ones. */ void *ones; }; /****************************************************************************/ /* * MMC-over-SPI protocol glue, used by the MMC stack interface */ static inline int mmc_cs_off(struct mmc_spi_host *host) { /* chipselect will always be inactive after setup() */ return spi_setup(host->spi); } static int mmc_spi_readbytes(struct mmc_spi_host *host, unsigned int len) { if (len > sizeof(*host->data)) { WARN_ON(1); return -EIO; } host->status.len = len; return spi_sync_locked(host->spi, &host->readback); } static int mmc_spi_skip(struct mmc_spi_host *host, unsigned long timeout, unsigned n, u8 byte) { u8 *cp = host->data->status; unsigned long start = jiffies; do { int status; unsigned i; status = mmc_spi_readbytes(host, n); if (status < 0) return status; for (i = 0; i < n; i++) { if (cp[i] != byte) return cp[i]; } /* If we need long timeouts, we may release the CPU */ cond_resched(); } while (time_is_after_jiffies(start + timeout)); return -ETIMEDOUT; } static inline int mmc_spi_wait_unbusy(struct mmc_spi_host *host, unsigned long timeout) { return mmc_spi_skip(host, timeout, sizeof(host->data->status), 0); } static int mmc_spi_readtoken(struct mmc_spi_host *host, unsigned long timeout) { return mmc_spi_skip(host, timeout, 1, 0xff); } /* * Note that for SPI, cmd->resp[0] is not the same data as "native" protocol * hosts return! The low byte holds R1_SPI bits. The next byte may hold * R2_SPI bits ... for SEND_STATUS, or after data read errors. * * cmd->resp[1] holds any four-byte response, for R3 (READ_OCR) and on * newer cards R7 (IF_COND). */ static char *maptype(struct mmc_command *cmd) { switch (mmc_spi_resp_type(cmd)) { case MMC_RSP_SPI_R1: return "R1"; case MMC_RSP_SPI_R1B: return "R1B"; case MMC_RSP_SPI_R2: return "R2/R5"; case MMC_RSP_SPI_R3: return "R3/R4/R7"; default: return "?"; } } /* return zero, else negative errno after setting cmd->error */ static int mmc_spi_response_get(struct mmc_spi_host *host, struct mmc_command *cmd, int cs_on) { unsigned long timeout_ms; u8 *cp = host->data->status; u8 *end = cp + host->t.len; int value = 0; int bitshift; u8 leftover = 0; unsigned short rotator; int i; char tag[32]; snprintf(tag, sizeof(tag), " ... CMD%d response SPI_%s", cmd->opcode, maptype(cmd)); /* Except for data block reads, the whole response will already * be stored in the scratch buffer. It's somewhere after the * command and the first byte we read after it. We ignore that * first byte. After STOP_TRANSMISSION command it may include * two data bits, but otherwise it's all ones. */ cp += 8; while (cp < end && *cp == 0xff) cp++; /* Data block reads (R1 response types) may need more data... */ if (cp == end) { cp = host->data->status; end = cp+1; /* Card sends N(CR) (== 1..8) bytes of all-ones then one * status byte ... and we already scanned 2 bytes. * * REVISIT block read paths use nasty byte-at-a-time I/O * so it can always DMA directly into the target buffer. * It'd probably be better to memcpy() the first chunk and * avoid extra i/o calls... * * Note we check for more than 8 bytes, because in practice, * some SD cards are slow... */ for (i = 2; i < 16; i++) { value = mmc_spi_readbytes(host, 1); if (value < 0) goto done; if (*cp != 0xff) goto checkstatus; } value = -ETIMEDOUT; goto done; } checkstatus: bitshift = 0; if (*cp & 0x80) { /* Houston, we have an ugly card with a bit-shifted response */ rotator = *cp++ << 8; /* read the next byte */ if (cp == end) { value = mmc_spi_readbytes(host, 1); if (value < 0) goto done; cp = host->data->status; end = cp+1; } rotator |= *cp++; while (rotator & 0x8000) { bitshift++; rotator <<= 1; } cmd->resp[0] = rotator >> 8; leftover = rotator; } else { cmd->resp[0] = *cp++; } cmd->error = 0; /* Status byte: the entire seven-bit R1 response. */ if (cmd->resp[0] != 0) { if ((R1_SPI_PARAMETER | R1_SPI_ADDRESS) & cmd->resp[0]) value = -EFAULT; /* Bad address */ else if (R1_SPI_ILLEGAL_COMMAND & cmd->resp[0]) value = -ENOSYS; /* Function not implemented */ else if (R1_SPI_COM_CRC & cmd->resp[0]) value = -EILSEQ; /* Illegal byte sequence */ else if ((R1_SPI_ERASE_SEQ | R1_SPI_ERASE_RESET) & cmd->resp[0]) value = -EIO; /* I/O error */ /* else R1_SPI_IDLE, "it's resetting" */ } switch (mmc_spi_resp_type(cmd)) { /* SPI R1B == R1 + busy; STOP_TRANSMISSION (for multiblock reads) * and less-common stuff like various erase operations. */ case MMC_RSP_SPI_R1B: /* maybe we read all the busy tokens already */ while (cp < end && *cp == 0) cp++; if (cp == end) { timeout_ms = cmd->busy_timeout ? cmd->busy_timeout : MMC_SPI_R1B_TIMEOUT_MS; mmc_spi_wait_unbusy(host, msecs_to_jiffies(timeout_ms)); } break; /* SPI R2 == R1 + second status byte; SEND_STATUS * SPI R5 == R1 + data byte; IO_RW_DIRECT */ case MMC_RSP_SPI_R2: /* read the next byte */ if (cp == end) { value = mmc_spi_readbytes(host, 1); if (value < 0) goto done; cp = host->data->status; end = cp+1; } if (bitshift) { rotator = leftover << 8; rotator |= *cp << bitshift; cmd->resp[0] |= (rotator & 0xFF00); } else { cmd->resp[0] |= *cp << 8; } break; /* SPI R3, R4, or R7 == R1 + 4 bytes */ case MMC_RSP_SPI_R3: rotator = leftover << 8; cmd->resp[1] = 0; for (i = 0; i < 4; i++) { cmd->resp[1] <<= 8; /* read the next byte */ if (cp == end) { value = mmc_spi_readbytes(host, 1); if (value < 0) goto done; cp = host->data->status; end = cp+1; } if (bitshift) { rotator |= *cp++ << bitshift; cmd->resp[1] |= (rotator >> 8); rotator <<= 8; } else { cmd->resp[1] |= *cp++; } } break; /* SPI R1 == just one status byte */ case MMC_RSP_SPI_R1: break; default: dev_dbg(&host->spi->dev, "bad response type %04x\n", mmc_spi_resp_type(cmd)); if (value >= 0) value = -EINVAL; goto done; } if (value < 0) dev_dbg(&host->spi->dev, "%s: resp %04x %08x\n", tag, cmd->resp[0], cmd->resp[1]); /* disable chipselect on errors and some success cases */ if (value >= 0 && cs_on) return value; done: if (value < 0) cmd->error = value; mmc_cs_off(host); return value; } /* Issue command and read its response. * Returns zero on success, negative for error. * * On error, caller must cope with mmc core retry mechanism. That * means immediate low-level resubmit, which affects the bus lock... */ static int mmc_spi_command_send(struct mmc_spi_host *host, struct mmc_request *mrq, struct mmc_command *cmd, int cs_on) { struct scratch *data = host->data; u8 *cp = data->status; int status; struct spi_transfer *t; /* We can handle most commands (except block reads) in one full * duplex I/O operation before either starting the next transfer * (data block or command) or else deselecting the card. * * First, write 7 bytes: * - an all-ones byte to ensure the card is ready * - opcode byte (plus start and transmission bits) * - four bytes of big-endian argument * - crc7 (plus end bit) ... always computed, it's cheap * * We init the whole buffer to all-ones, which is what we need * to write while we're reading (later) response data. */ memset(cp, 0xff, sizeof(data->status)); cp[1] = 0x40 | cmd->opcode; put_unaligned_be32(cmd->arg, cp + 2); cp[6] = crc7_be(0, cp + 1, 5) | 0x01; cp += 7; /* Then, read up to 13 bytes (while writing all-ones): * - N(CR) (== 1..8) bytes of all-ones * - status byte (for all response types) * - the rest of the response, either: * + nothing, for R1 or R1B responses * + second status byte, for R2 responses * + four data bytes, for R3 and R7 responses * * Finally, read some more bytes ... in the nice cases we know in * advance how many, and reading 1 more is always OK: * - N(EC) (== 0..N) bytes of all-ones, before deselect/finish * - N(RC) (== 1..N) bytes of all-ones, before next command * - N(WR) (== 1..N) bytes of all-ones, before data write * * So in those cases one full duplex I/O of at most 21 bytes will * handle the whole command, leaving the card ready to receive a * data block or new command. We do that whenever we can, shaving * CPU and IRQ costs (especially when using DMA or FIFOs). * * There are two other cases, where it's not generally practical * to rely on a single I/O: * * - R1B responses need at least N(EC) bytes of all-zeroes. * * In this case we can *try* to fit it into one I/O, then * maybe read more data later. * * - Data block reads are more troublesome, since a variable * number of padding bytes precede the token and data. * + N(CX) (== 0..8) bytes of all-ones, before CSD or CID * + N(AC) (== 1..many) bytes of all-ones * * In this case we currently only have minimal speedups here: * when N(CR) == 1 we can avoid I/O in response_get(). */ if (cs_on && (mrq->data->flags & MMC_DATA_READ)) { cp += 2; /* min(N(CR)) + status */ /* R1 */ } else { cp += 10; /* max(N(CR)) + status + min(N(RC),N(WR)) */ if (cmd->flags & MMC_RSP_SPI_S2) /* R2/R5 */ cp++; else if (cmd->flags & MMC_RSP_SPI_B4) /* R3/R4/R7 */ cp += 4; else if (cmd->flags & MMC_RSP_BUSY) /* R1B */ cp = data->status + sizeof(data->status); /* else: R1 (most commands) */ } dev_dbg(&host->spi->dev, " CMD%d, resp %s\n", cmd->opcode, maptype(cmd)); /* send command, leaving chipselect active */ spi_message_init(&host->m); t = &host->t; memset(t, 0, sizeof(*t)); t->tx_buf = t->rx_buf = data->status; t->len = cp - data->status; t->cs_change = 1; spi_message_add_tail(t, &host->m); status = spi_sync_locked(host->spi, &host->m); if (status < 0) { dev_dbg(&host->spi->dev, " ... write returned %d\n", status); cmd->error = status; return status; } /* after no-data commands and STOP_TRANSMISSION, chipselect off */ return mmc_spi_response_get(host, cmd, cs_on); } /* Build data message with up to four separate transfers. For TX, we * start by writing the data token. And in most cases, we finish with * a status transfer. * * We always provide TX data for data and CRC. The MMC/SD protocol * requires us to write ones; but Linux defaults to writing zeroes; * so we explicitly initialize it to all ones on RX paths. */ static void mmc_spi_setup_data_message( struct mmc_spi_host *host, int multiple, enum dma_data_direction direction) { struct spi_transfer *t; struct scratch *scratch = host->data; spi_message_init(&host->m); /* for reads, readblock() skips 0xff bytes before finding * the token; for writes, this transfer issues that token. */ if (direction == DMA_TO_DEVICE) { t = &host->token; memset(t, 0, sizeof(*t)); t->len = 1; if (multiple) scratch->data_token = SPI_TOKEN_MULTI_WRITE; else scratch->data_token = SPI_TOKEN_SINGLE; t->tx_buf = &scratch->data_token; spi_message_add_tail(t, &host->m); } /* Body of transfer is buffer, then CRC ... * either TX-only, or RX with TX-ones. */ t = &host->t; memset(t, 0, sizeof(*t)); t->tx_buf = host->ones; /* length and actual buffer info are written later */ spi_message_add_tail(t, &host->m); t = &host->crc; memset(t, 0, sizeof(*t)); t->len = 2; if (direction == DMA_TO_DEVICE) { /* the actual CRC may get written later */ t->tx_buf = &scratch->crc_val; } else { t->tx_buf = host->ones; t->rx_buf = &scratch->crc_val; } spi_message_add_tail(t, &host->m); /* * A single block read is followed by N(EC) [0+] all-ones bytes * before deselect ... don't bother. * * Multiblock reads are followed by N(AC) [1+] all-ones bytes before * the next block is read, or a STOP_TRANSMISSION is issued. We'll * collect that single byte, so readblock() doesn't need to. * * For a write, the one-byte data response follows immediately, then * come zero or more busy bytes, then N(WR) [1+] all-ones bytes. * Then single block reads may deselect, and multiblock ones issue * the next token (next data block, or STOP_TRAN). We can try to * minimize I/O ops by using a single read to collect end-of-busy. */ if (multiple || direction == DMA_TO_DEVICE) { t = &host->early_status; memset(t, 0, sizeof(*t)); t->len = (direction == DMA_TO_DEVICE) ? sizeof(scratch->status) : 1; t->tx_buf = host->ones; t->rx_buf = scratch->status; t->cs_change = 1; spi_message_add_tail(t, &host->m); } } /* * Write one block: * - caller handled preceding N(WR) [1+] all-ones bytes * - data block * + token * + data bytes * + crc16 * - an all-ones byte ... card writes a data-response byte * - followed by N(EC) [0+] all-ones bytes, card writes zero/'busy' * * Return negative errno, else success. */ static int mmc_spi_writeblock(struct mmc_spi_host *host, struct spi_transfer *t, unsigned long timeout) { struct spi_device *spi = host->spi; int status, i; struct scratch *scratch = host->data; u32 pattern; if (host->mmc->use_spi_crc) scratch->crc_val = cpu_to_be16(crc_itu_t(0, t->tx_buf, t->len)); status = spi_sync_locked(spi, &host->m); if (status != 0) { dev_dbg(&spi->dev, "write error (%d)\n", status); return status; } /* * Get the transmission data-response reply. It must follow * immediately after the data block we transferred. This reply * doesn't necessarily tell whether the write operation succeeded; * it just says if the transmission was ok and whether *earlier* * writes succeeded; see the standard. * * In practice, there are (even modern SDHC-)cards which are late * in sending the response, and miss the time frame by a few bits, * so we have to cope with this situation and check the response * bit-by-bit. Arggh!!! */ pattern = get_unaligned_be32(scratch->status); /* First 3 bit of pattern are undefined */ pattern |= 0xE0000000; /* left-adjust to leading 0 bit */ while (pattern & 0x80000000) pattern <<= 1; /* right-adjust for pattern matching. Code is in bit 4..0 now. */ pattern >>= 27; switch (pattern) { case SPI_RESPONSE_ACCEPTED: status = 0; break; case SPI_RESPONSE_CRC_ERR: /* host shall then issue MMC_STOP_TRANSMISSION */ status = -EILSEQ; break; case SPI_RESPONSE_WRITE_ERR: /* host shall then issue MMC_STOP_TRANSMISSION, * and should MMC_SEND_STATUS to sort it out */ status = -EIO; break; default: status = -EPROTO; break; } if (status != 0) { dev_dbg(&spi->dev, "write error %02x (%d)\n", scratch->status[0], status); return status; } t->tx_buf += t->len; /* Return when not busy. If we didn't collect that status yet, * we'll need some more I/O. */ for (i = 4; i < sizeof(scratch->status); i++) { /* card is non-busy if the most recent bit is 1 */ if (scratch->status[i] & 0x01) return 0; } return mmc_spi_wait_unbusy(host, timeout); } /* * Read one block: * - skip leading all-ones bytes ... either * + N(AC) [1..f(clock,CSD)] usually, else * + N(CX) [0..8] when reading CSD or CID * - data block * + token ... if error token, no data or crc * + data bytes * + crc16 * * After single block reads, we're done; N(EC) [0+] all-ones bytes follow * before dropping chipselect. * * For multiblock reads, caller either reads the next block or issues a * STOP_TRANSMISSION command. */ static int mmc_spi_readblock(struct mmc_spi_host *host, struct spi_transfer *t, unsigned long timeout) { struct spi_device *spi = host->spi; int status; struct scratch *scratch = host->data; unsigned int bitshift; u8 leftover; /* At least one SD card sends an all-zeroes byte when N(CX) * applies, before the all-ones bytes ... just cope with that. */ status = mmc_spi_readbytes(host, 1); if (status < 0) return status; status = scratch->status[0]; if (status == 0xff || status == 0) status = mmc_spi_readtoken(host, timeout); if (status < 0) { dev_dbg(&spi->dev, "read error %02x (%d)\n", status, status); return status; } /* The token may be bit-shifted... * the first 0-bit precedes the data stream. */ bitshift = 7; while (status & 0x80) { status <<= 1; bitshift--; } leftover = status << 1; status = spi_sync_locked(spi, &host->m); if (status < 0) { dev_dbg(&spi->dev, "read error %d\n", status); return status; } if (bitshift) { /* Walk through the data and the crc and do * all the magic to get byte-aligned data. */ u8 *cp = t->rx_buf; unsigned int len; unsigned int bitright = 8 - bitshift; u8 temp; for (len = t->len; len; len--) { temp = *cp; *cp++ = leftover | (temp >> bitshift); leftover = temp << bitright; } cp = (u8 *) &scratch->crc_val; temp = *cp; *cp++ = leftover | (temp >> bitshift); leftover = temp << bitright; temp = *cp; *cp = leftover | (temp >> bitshift); } if (host->mmc->use_spi_crc) { u16 crc = crc_itu_t(0, t->rx_buf, t->len); be16_to_cpus(&scratch->crc_val); if (scratch->crc_val != crc) { dev_dbg(&spi->dev, "read - crc error: crc_val=0x%04x, computed=0x%04x len=%d\n", scratch->crc_val, crc, t->len); return -EILSEQ; } } t->rx_buf += t->len; return 0; } /* * An MMC/SD data stage includes one or more blocks, optional CRCs, * and inline handshaking. That handhaking makes it unlike most * other SPI protocol stacks. */ static void mmc_spi_data_do(struct mmc_spi_host *host, struct mmc_command *cmd, struct mmc_data *data, u32 blk_size) { struct spi_device *spi = host->spi; struct spi_transfer *t; enum dma_data_direction direction; struct scatterlist *sg; unsigned n_sg; int multiple = (data->blocks > 1); u32 clock_rate; unsigned long timeout; direction = mmc_get_dma_dir(data); mmc_spi_setup_data_message(host, multiple, direction); t = &host->t; if (t->speed_hz) clock_rate = t->speed_hz; else clock_rate = spi->max_speed_hz; timeout = data->timeout_ns / 1000 + data->timeout_clks * 1000000 / clock_rate; timeout = usecs_to_jiffies((unsigned int)timeout) + 1; /* Handle scatterlist segments one at a time, with synch for * each 512-byte block */ for_each_sg(data->sg, sg, data->sg_len, n_sg) { int status = 0; void *kmap_addr; unsigned length = sg->length; /* allow pio too; we don't allow highmem */ kmap_addr = kmap(sg_page(sg)); if (direction == DMA_TO_DEVICE) t->tx_buf = kmap_addr + sg->offset; else t->rx_buf = kmap_addr + sg->offset; /* transfer each block, and update request status */ while (length) { t->len = min(length, blk_size); dev_dbg(&host->spi->dev, " %s block, %d bytes\n", (direction == DMA_TO_DEVICE) ? "write" : "read", t->len); if (direction == DMA_TO_DEVICE) status = mmc_spi_writeblock(host, t, timeout); else status = mmc_spi_readblock(host, t, timeout); if (status < 0) break; data->bytes_xfered += t->len; length -= t->len; if (!multiple) break; } /* discard mappings */ if (direction == DMA_FROM_DEVICE) flush_dcache_page(sg_page(sg)); kunmap(sg_page(sg)); if (status < 0) { data->error = status; dev_dbg(&spi->dev, "%s status %d\n", (direction == DMA_TO_DEVICE) ? "write" : "read", status); break; } } /* NOTE some docs describe an MMC-only SET_BLOCK_COUNT (CMD23) that * can be issued before multiblock writes. Unlike its more widely * documented analogue for SD cards (SET_WR_BLK_ERASE_COUNT, ACMD23), * that can affect the STOP_TRAN logic. Complete (and current) * MMC specs should sort that out before Linux starts using CMD23. */ if (direction == DMA_TO_DEVICE && multiple) { struct scratch *scratch = host->data; int tmp; const unsigned statlen = sizeof(scratch->status); dev_dbg(&spi->dev, " STOP_TRAN\n"); /* Tweak the per-block message we set up earlier by morphing * it to hold single buffer with the token followed by some * all-ones bytes ... skip N(BR) (0..1), scan the rest for * "not busy any longer" status, and leave chip selected. */ INIT_LIST_HEAD(&host->m.transfers); list_add(&host->early_status.transfer_list, &host->m.transfers); memset(scratch->status, 0xff, statlen); scratch->status[0] = SPI_TOKEN_STOP_TRAN; host->early_status.tx_buf = host->early_status.rx_buf; host->early_status.len = statlen; tmp = spi_sync_locked(spi, &host->m); if (tmp < 0) { if (!data->error) data->error = tmp; return; } /* Ideally we collected "not busy" status with one I/O, * avoiding wasteful byte-at-a-time scanning... but more * I/O is often needed. */ for (tmp = 2; tmp < statlen; tmp++) { if (scratch->status[tmp] != 0) return; } tmp = mmc_spi_wait_unbusy(host, timeout); if (tmp < 0 && !data->error) data->error = tmp; } } /****************************************************************************/ /* * MMC driver implementation -- the interface to the MMC stack */ static void mmc_spi_request(struct mmc_host *mmc, struct mmc_request *mrq) { struct mmc_spi_host *host = mmc_priv(mmc); int status = -EINVAL; int crc_retry = 5; struct mmc_command stop; #ifdef DEBUG /* MMC core and layered drivers *MUST* issue SPI-aware commands */ { struct mmc_command *cmd; int invalid = 0; cmd = mrq->cmd; if (!mmc_spi_resp_type(cmd)) { dev_dbg(&host->spi->dev, "bogus command\n"); cmd->error = -EINVAL; invalid = 1; } cmd = mrq->stop; if (cmd && !mmc_spi_resp_type(cmd)) { dev_dbg(&host->spi->dev, "bogus STOP command\n"); cmd->error = -EINVAL; invalid = 1; } if (invalid) { dump_stack(); mmc_request_done(host->mmc, mrq); return; } } #endif /* request exclusive bus access */ spi_bus_lock(host->spi->master); crc_recover: /* issue command; then optionally data and stop */ status = mmc_spi_command_send(host, mrq, mrq->cmd, mrq->data != NULL); if (status == 0 && mrq->data) { mmc_spi_data_do(host, mrq->cmd, mrq->data, mrq->data->blksz); /* * The SPI bus is not always reliable for large data transfers. * If an occasional crc error is reported by the SD device with * data read/write over SPI, it may be recovered by repeating * the last SD command again. The retry count is set to 5 to * ensure the driver passes stress tests. */ if (mrq->data->error == -EILSEQ && crc_retry) { stop.opcode = MMC_STOP_TRANSMISSION; stop.arg = 0; stop.flags = MMC_RSP_SPI_R1B | MMC_RSP_R1B | MMC_CMD_AC; status = mmc_spi_command_send(host, mrq, &stop, 0); crc_retry--; mrq->data->error = 0; goto crc_recover; } if (mrq->stop) status = mmc_spi_command_send(host, mrq, mrq->stop, 0); else mmc_cs_off(host); } /* release the bus */ spi_bus_unlock(host->spi->master); mmc_request_done(host->mmc, mrq); } /* See Section 6.4.1, in SD "Simplified Physical Layer Specification 2.0" * * NOTE that here we can't know that the card has just been powered up; * not all MMC/SD sockets support power switching. * * FIXME when the card is still in SPI mode, e.g. from a previous kernel, * this doesn't seem to do the right thing at all... */ static void mmc_spi_initsequence(struct mmc_spi_host *host) { /* Try to be very sure any previous command has completed; * wait till not-busy, skip debris from any old commands. */ mmc_spi_wait_unbusy(host, msecs_to_jiffies(MMC_SPI_INIT_TIMEOUT_MS)); mmc_spi_readbytes(host, 10); /* * Do a burst with chipselect active-high. We need to do this to * meet the requirement of 74 clock cycles with both chipselect * and CMD (MOSI) high before CMD0 ... after the card has been * powered up to Vdd(min), and so is ready to take commands. * * Some cards are particularly needy of this (e.g. Viking "SD256") * while most others don't seem to care. * * Note that this is one of the places MMC/SD plays games with the * SPI protocol. Another is that when chipselect is released while * the card returns BUSY status, the clock must issue several cycles * with chipselect high before the card will stop driving its output. * * SPI_CS_HIGH means "asserted" here. In some cases like when using * GPIOs for chip select, SPI_CS_HIGH is set but this will be logically * inverted by gpiolib, so if we want to ascertain to drive it high * we should toggle the default with an XOR as we do here. */ host->spi->mode ^= SPI_CS_HIGH; if (spi_setup(host->spi) != 0) { /* Just warn; most cards work without it. */ dev_warn(&host->spi->dev, "can't change chip-select polarity\n"); host->spi->mode ^= SPI_CS_HIGH; } else { mmc_spi_readbytes(host, 18); host->spi->mode ^= SPI_CS_HIGH; if (spi_setup(host->spi) != 0) { /* Wot, we can't get the same setup we had before? */ dev_err(&host->spi->dev, "can't restore chip-select polarity\n"); } } } static char *mmc_powerstring(u8 power_mode) { switch (power_mode) { case MMC_POWER_OFF: return "off"; case MMC_POWER_UP: return "up"; case MMC_POWER_ON: return "on"; } return "?"; } static void mmc_spi_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) { struct mmc_spi_host *host = mmc_priv(mmc); if (host->power_mode != ios->power_mode) { int canpower; canpower = host->pdata && host->pdata->setpower; dev_dbg(&host->spi->dev, "power %s (%d)%s\n", mmc_powerstring(ios->power_mode), ios->vdd, canpower ? ", can switch" : ""); /* switch power on/off if possible, accounting for * max 250msec powerup time if needed. */ if (canpower) { switch (ios->power_mode) { case MMC_POWER_OFF: case MMC_POWER_UP: host->pdata->setpower(&host->spi->dev, ios->vdd); if (ios->power_mode == MMC_POWER_UP) msleep(host->powerup_msecs); } } /* See 6.4.1 in the simplified SD card physical spec 2.0 */ if (ios->power_mode == MMC_POWER_ON) mmc_spi_initsequence(host); /* If powering down, ground all card inputs to avoid power * delivery from data lines! On a shared SPI bus, this * will probably be temporary; 6.4.2 of the simplified SD * spec says this must last at least 1msec. * * - Clock low means CPOL 0, e.g. mode 0 * - MOSI low comes from writing zero * - Chipselect is usually active low... */ if (canpower && ios->power_mode == MMC_POWER_OFF) { int mres; u8 nullbyte = 0; host->spi->mode &= ~(SPI_CPOL|SPI_CPHA); mres = spi_setup(host->spi); if (mres < 0) dev_dbg(&host->spi->dev, "switch to SPI mode 0 failed\n"); if (spi_write(host->spi, &nullbyte, 1) < 0) dev_dbg(&host->spi->dev, "put spi signals to low failed\n"); /* * Now clock should be low due to spi mode 0; * MOSI should be low because of written 0x00; * chipselect should be low (it is active low) * power supply is off, so now MMC is off too! * * FIXME no, chipselect can be high since the * device is inactive and SPI_CS_HIGH is clear... */ msleep(10); if (mres == 0) { host->spi->mode |= (SPI_CPOL|SPI_CPHA); mres = spi_setup(host->spi); if (mres < 0) dev_dbg(&host->spi->dev, "switch back to SPI mode 3 failed\n"); } } host->power_mode = ios->power_mode; } if (host->spi->max_speed_hz != ios->clock && ios->clock != 0) { int status; host->spi->max_speed_hz = ios->clock; status = spi_setup(host->spi); dev_dbg(&host->spi->dev, " clock to %d Hz, %d\n", host->spi->max_speed_hz, status); } } static const struct mmc_host_ops mmc_spi_ops = { .request = mmc_spi_request, .set_ios = mmc_spi_set_ios, .get_ro = mmc_gpio_get_ro, .get_cd = mmc_gpio_get_cd, }; /****************************************************************************/ /* * SPI driver implementation */ static irqreturn_t mmc_spi_detect_irq(int irq, void *mmc) { struct mmc_spi_host *host = mmc_priv(mmc); u16 delay_msec = max(host->pdata->detect_delay, (u16)100); mmc_detect_change(mmc, msecs_to_jiffies(delay_msec)); return IRQ_HANDLED; } static int mmc_spi_probe(struct spi_device *spi) { void *ones; struct mmc_host *mmc; struct mmc_spi_host *host; int status; bool has_ro = false; /* We rely on full duplex transfers, mostly to reduce * per-transfer overheads (by making fewer transfers). */ if (spi->master->flags & SPI_MASTER_HALF_DUPLEX) return -EINVAL; /* MMC and SD specs only seem to care that sampling is on the * rising edge ... meaning SPI modes 0 or 3. So either SPI mode * should be legit. We'll use mode 0 since the steady state is 0, * which is appropriate for hotplugging, unless the platform data * specify mode 3 (if hardware is not compatible to mode 0). */ if (spi->mode != SPI_MODE_3) spi->mode = SPI_MODE_0; spi->bits_per_word = 8; status = spi_setup(spi); if (status < 0) { dev_dbg(&spi->dev, "needs SPI mode %02x, %d KHz; %d\n", spi->mode, spi->max_speed_hz / 1000, status); return status; } /* We need a supply of ones to transmit. This is the only time * the CPU touches these, so cache coherency isn't a concern. * * NOTE if many systems use more than one MMC-over-SPI connector * it'd save some memory to share this. That's evidently rare. */ status = -ENOMEM; ones = kmalloc(MMC_SPI_BLOCKSIZE, GFP_KERNEL); if (!ones) goto nomem; memset(ones, 0xff, MMC_SPI_BLOCKSIZE); mmc = mmc_alloc_host(sizeof(*host), &spi->dev); if (!mmc) goto nomem; mmc->ops = &mmc_spi_ops; mmc->max_blk_size = MMC_SPI_BLOCKSIZE; mmc->max_segs = MMC_SPI_BLOCKSATONCE; mmc->max_req_size = MMC_SPI_BLOCKSATONCE * MMC_SPI_BLOCKSIZE; mmc->max_blk_count = MMC_SPI_BLOCKSATONCE; mmc->caps = MMC_CAP_SPI; /* SPI doesn't need the lowspeed device identification thing for * MMC or SD cards, since it never comes up in open drain mode. * That's good; some SPI masters can't handle very low speeds! * * However, low speed SDIO cards need not handle over 400 KHz; * that's the only reason not to use a few MHz for f_min (until * the upper layer reads the target frequency from the CSD). */ mmc->f_min = 400000; mmc->f_max = spi->max_speed_hz; host = mmc_priv(mmc); host->mmc = mmc; host->spi = spi; host->ones = ones; dev_set_drvdata(&spi->dev, mmc); /* Platform data is used to hook up things like card sensing * and power switching gpios. */ host->pdata = mmc_spi_get_pdata(spi); if (host->pdata) mmc->ocr_avail = host->pdata->ocr_mask; if (!mmc->ocr_avail) { dev_warn(&spi->dev, "ASSUMING 3.2-3.4 V slot power\n"); mmc->ocr_avail = MMC_VDD_32_33|MMC_VDD_33_34; } if (host->pdata && host->pdata->setpower) { host->powerup_msecs = host->pdata->powerup_msecs; if (!host->powerup_msecs || host->powerup_msecs > 250) host->powerup_msecs = 250; } /* Preallocate buffers */ host->data = kmalloc(sizeof(*host->data), GFP_KERNEL); if (!host->data) goto fail_nobuf1; /* setup message for status/busy readback */ spi_message_init(&host->readback); spi_message_add_tail(&host->status, &host->readback); host->status.tx_buf = host->ones; host->status.rx_buf = &host->data->status; host->status.cs_change = 1; /* register card detect irq */ if (host->pdata && host->pdata->init) { status = host->pdata->init(&spi->dev, mmc_spi_detect_irq, mmc); if (status != 0) goto fail_glue_init; } /* pass platform capabilities, if any */ if (host->pdata) { mmc->caps |= host->pdata->caps; mmc->caps2 |= host->pdata->caps2; } status = mmc_add_host(mmc); if (status != 0) goto fail_glue_init; /* * Index 0 is card detect * Old boardfiles were specifying 1 ms as debounce */ status = mmc_gpiod_request_cd(mmc, NULL, 0, false, 1000); if (status == -EPROBE_DEFER) goto fail_gpiod_request; if (!status) { /* * The platform has a CD GPIO signal that may support * interrupts, so let mmc_gpiod_request_cd_irq() decide * if polling is needed or not. */ mmc->caps &= ~MMC_CAP_NEEDS_POLL; mmc_gpiod_request_cd_irq(mmc); } mmc_detect_change(mmc, 0); /* Index 1 is write protect/read only */ status = mmc_gpiod_request_ro(mmc, NULL, 1, 0); if (status == -EPROBE_DEFER) goto fail_gpiod_request; if (!status) has_ro = true; dev_info(&spi->dev, "SD/MMC host %s%s%s%s\n", dev_name(&mmc->class_dev), has_ro ? "" : ", no WP", (host->pdata && host->pdata->setpower) ? "" : ", no poweroff", (mmc->caps & MMC_CAP_NEEDS_POLL) ? ", cd polling" : ""); return 0; fail_gpiod_request: mmc_remove_host(mmc); fail_glue_init: kfree(host->data); fail_nobuf1: mmc_spi_put_pdata(spi); mmc_free_host(mmc); nomem: kfree(ones); return status; } static int mmc_spi_remove(struct spi_device *spi) { struct mmc_host *mmc = dev_get_drvdata(&spi->dev); struct mmc_spi_host *host = mmc_priv(mmc); /* prevent new mmc_detect_change() calls */ if (host->pdata && host->pdata->exit) host->pdata->exit(&spi->dev, mmc); mmc_remove_host(mmc); kfree(host->data); kfree(host->ones); spi->max_speed_hz = mmc->f_max; mmc_spi_put_pdata(spi); mmc_free_host(mmc); return 0; } static const struct spi_device_id mmc_spi_dev_ids[] = { { "mmc-spi-slot"}, { }, }; MODULE_DEVICE_TABLE(spi, mmc_spi_dev_ids); static const struct of_device_id mmc_spi_of_match_table[] = { { .compatible = "mmc-spi-slot", }, {}, }; MODULE_DEVICE_TABLE(of, mmc_spi_of_match_table); static struct spi_driver mmc_spi_driver = { .driver = { .name = "mmc_spi", .of_match_table = mmc_spi_of_match_table, }, .id_table = mmc_spi_dev_ids, .probe = mmc_spi_probe, .remove = mmc_spi_remove, }; module_spi_driver(mmc_spi_driver); MODULE_AUTHOR("Mike Lavender, David Brownell, Hans-Peter Nilsson, Jan Nikitenko"); MODULE_DESCRIPTION("SPI SD/MMC host driver"); MODULE_LICENSE("GPL"); MODULE_ALIAS("spi:mmc_spi");