/*------------------------------------------------------------------------ . smc9194.h . Copyright (C) 1996 by Erik Stahlman . . This software may be used and distributed according to the terms . of the GNU General Public License, incorporated herein by reference. . . This file contains register information and access macros for . the SMC91xxx chipset. . . Information contained in this file was obtained from the SMC91C94 . manual from SMC. To get a copy, if you really want one, you can find . information under www.smc.com in the components division. . ( this thanks to advice from Donald Becker ). . . Authors . Erik Stahlman ( erik@vt.edu ) . . History . 01/06/96 Erik Stahlman moved definitions here from main .c file . 01/19/96 Erik Stahlman polished this up some, and added better . error handling . ---------------------------------------------------------------------------*/ #ifndef _SMC9194_H_ #define _SMC9194_H_ /* I want some simple types */ typedef unsigned char byte; typedef unsigned short word; typedef unsigned long int dword; /* Because of bank switching, the SMC91xxx uses only 16 I/O ports */ #define SMC_IO_EXTENT 16 /*--------------------------------------------------------------- . . A description of the SMC registers is probably in order here, . although for details, the SMC datasheet is invaluable. . . Basically, the chip has 4 banks of registers ( 0 to 3 ), which . are accessed by writing a number into the BANK_SELECT register . ( I also use a SMC_SELECT_BANK macro for this ). . . The banks are configured so that for most purposes, bank 2 is all . that is needed for simple run time tasks. -----------------------------------------------------------------------*/ /* . Bank Select Register: . . yyyy yyyy 0000 00xx . xx = bank number . yyyy yyyy = 0x33, for identification purposes. */ #define BANK_SELECT 14 /* BANK 0 */ #define TCR 0 /* transmit control register */ #define TCR_ENABLE 0x0001 /* if this is 1, we can transmit */ #define TCR_PAD_ENABLE 0x0080 /* pads short packets to 64 bytes */ #define TCR_MON_CNS 0x0400 /* monitors the carrier status */ #define TCR_FDUPLX 0x0800 /* receive packets sent out */ #define TCR_STP_SQET 0x1000 /* stop transmitting if Signal quality error */ #define TCR_FDSE 0x8000 /* full duplex, switched ethernet */ #define TCR_CLEAR 0 /* do NOTHING */ /* the normal settings for the TCR register : */ /* QUESTION: do I want to enable padding of short packets ? */ #define TCR_NORMAL TCR_ENABLE #define EPH_STATUS 2 #define ES_LINK_OK 0x4000 /* is the link integrity ok ? */ #define RCR 4 #define RCR_SOFTRESET 0x8000 /* resets the chip */ #define RCR_STRIP_CRC 0x200 /* strips CRC */ #define RCR_ENABLE 0x100 /* IFF this is set, we can receive packets */ #define RCR_ALMUL 0x4 /* receive all multicast packets */ #define RCR_PROMISC 0x2 /* enable promiscuous mode */ /* the normal settings for the RCR register : */ #define RCR_NORMAL (RCR_STRIP_CRC | RCR_ENABLE) #define RCR_CLEAR 0x0 /* set it to a base state */ #define COUNTER 6 #define MIR 8 #define MCR 10 /* 12 is reserved */ /* BANK 1 */ #define CONFIG 0 #define CFG_AUI_SELECT 0x100 #define BASE 2 #define ADDR0 4 #define ADDR1 6 #define ADDR2 8 #define GENERAL 10 #define CONTROL 12 #define CTL_POWERDOWN 0x2000 #define CTL_LE_ENABLE 0x80 #define CTL_CR_ENABLE 0x40 #define CTL_TE_ENABLE 0x0020 #define CTL_AUTO_RELEASE 0x0800 #define CTL_EPROM_SELECT 0x0004 #define CTL_EPROM_RELOAD 0x0002 #define CTL_EPROM_STORE 0x0001 #define CTL_EPROM_ACCESS (CTL_EPROM_RELOAD | CTL_EPROM_STORE) /* high if Eprom is being read */ /* BANK 2 */ #define MMU_CMD 0 #define MC_BUSY 1 /* only readable bit in the register */ #define MC_NOP 0 #define MC_ALLOC 0x20 /* or with number of 256 byte packets */ #define MC_RESET 0x40 #define MC_REMOVE 0x60 /* remove the current rx packet */ #define MC_RELEASE 0x80 /* remove and release the current rx packet */ #define MC_FREEPKT 0xA0 /* Release packet in PNR register */ #define MC_ENQUEUE 0xC0 /* Enqueue the packet for transmit */ #define PNR_ARR 2 #define FIFO_PORTS 4 #define FP_RXEMPTY 0x8000 #define FP_TXEMPTY 0x80 #define POINTER 6 #define PTR_READ 0x2000 #define PTR_RCV 0x8000 #define PTR_AUTOINC 0x4000 #define DATA_1 8 #define DATA_2 10 #define INTERRUPT 12 #define INT_MASK 13 #define IM_RCV_INT 0x1 #define IM_TX_INT 0x2 #define IM_TX_EMPTY_INT 0x4 #define IM_ALLOC_INT 0x8 #define IM_RX_OVRN_INT 0x10 #define IM_EPH_INT 0x20 #define IM_ERCV_INT 0x40 /* not on SMC9192 */ /* BANK 3 */ #define MULTICAST1 0 #define MULTICAST2 2 #define MULTICAST3 4 #define MULTICAST4 6 #define MGMT 8 #define REVISION 10 /* ( hi: chip id low: rev # ) */ /* this is NOT on SMC9192 */ #define ERCV 12 #define CHIP_9190 3 #define CHIP_9194 4 #define CHIP_9195 5 #define CHIP_91100 7 /* . Transmit status bits */ #define TS_SUCCESS 0x0001 #define TS_LOSTCAR 0x0400 #define TS_LATCOL 0x0200 #define TS_16COL 0x0010 /* . Receive status bits */ #define RS_ALGNERR 0x8000 #define RS_BADCRC 0x2000 #define RS_ODDFRAME 0x1000 #define RS_TOOLONG 0x0800 #define RS_TOOSHORT 0x0400 #define RS_MULTICAST 0x0001 #define RS_ERRORS (RS_ALGNERR | RS_BADCRC | RS_TOOLONG | RS_TOOSHORT) /* * SMC91C96 ethernet config and status registers. * These are in the "attribute" space. */ #define ECOR 0x8000 #define ECOR_RESET 0x80 #define ECOR_LEVEL_IRQ 0x40 #define ECOR_WR_ATTRIB 0x04 #define ECOR_ENABLE 0x01 #define ECSR 0x8002 #define ECSR_IOIS8 0x20 #define ECSR_PWRDWN 0x04 #define ECSR_INT 0x02 /*---------------------------------------------------------------------- . Define the interrupts that I want to receive from the card . . I want: . IM_EPH_INT, for nasty errors . IM_RCV_INT, for happy received packets . IM_RX_OVRN_INT, because I have to kick the receiver --------------------------------------------------------------------------*/ #define SMC_INTERRUPT_MASK (IM_EPH_INT | IM_RX_OVRN_INT | IM_RCV_INT) /* store this information for the driver.. */ struct smc_local { /* these are things that the kernel wants me to keep, so users can find out semi-useless statistics of how well the card is performing */ struct net_device_stats stats; /* If I have to wait until memory is available to send a packet, I will store the skbuff here, until I get the desired memory. Then, I'll send it out and free it. */ struct sk_buff * saved_skb; /* . This keeps track of how many packets that I have . sent out. When an TX_EMPTY interrupt comes, I know . that all of these have been sent. */ int packets_waiting; /* . Interface status. These correspond to the parameters . in the ethtool_cmd structure. */ u8 duplex; u8 port; }; #endif /* _SMC_9194_H_ */