/* $Id: auxio.h,v 1.1.1.1 2003/06/23 22:18:42 jharrell Exp $
 * auxio.h:  Definitions and code for the Auxiliary I/O register.
 *
 * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
 */
#ifndef _SPARC64_AUXIO_H
#define _SPARC64_AUXIO_H

#include <asm/system.h>
#include <asm/io.h>

/* FIXME: All of this should be checked for sun4u. It has /sbus/auxio, but
   I don't know whether it is the same and don't have a floppy */

extern unsigned long auxio_register;

/* This register is an unsigned char in IO space.  It does two things.
 * First, it is used to control the front panel LED light on machines
 * that have it (good for testing entry points to trap handlers and irq's)
 * Secondly, it controls various floppy drive parameters.
 */
#define AUXIO_ORMEIN      0xf0    /* All writes must set these bits. */
#define AUXIO_ORMEIN4M    0xc0    /* sun4m - All writes must set these bits. */
#define AUXIO_FLPY_DENS   0x20    /* Floppy density, high if set. Read only. */
#define AUXIO_FLPY_DCHG   0x10    /* A disk change occurred.  Read only. */
#define AUXIO_EDGE_ON     0x10    /* sun4m - On means Jumper block is in. */
#define AUXIO_FLPY_DSEL   0x08    /* Drive select/start-motor. Write only. */
#define AUXIO_LINK_TEST   0x08    /* sun4m - On means TPE Carrier detect. */

/* Set the following to one, then zero, after doing a pseudo DMA transfer. */
#define AUXIO_FLPY_TCNT   0x04    /* Floppy terminal count. Write only. */

/* Set the following to zero to eject the floppy. */
#define AUXIO_FLPY_EJCT   0x02    /* Eject floppy disk.  Write only. */
#define AUXIO_LED         0x01    /* On if set, off if unset. Read/Write */

#define AUXREG   (auxio_register)

/* These are available on sun4c */
#define TURN_ON_LED   \
do {	if (AUXREG) \
		sbus_writeb(sbus_readb(AUXREG) | \
			    (AUXIO_ORMEIN | AUXIO_LED), AUXREG); \
} while(0)
#define TURN_OFF_LED  \
do {	if (AUXREG) \
		sbus_writeb((sbus_readb(AUXREG) | \
			     AUXIO_ORMEIN) & (~AUXIO_LED), \
			    AUXREG); \
} while(0)
#define FLIP_LED	\
do {	if (AUXREG)  \
		sbus_writeb((sbus_readb(AUXREG) | \
			     AUXIO_ORMEIN) ^ AUXIO_LEN, \
			    AUXREG); \
} while(0)
#define FLPY_MOTORON	\
do {	if (AUXREG) \
		sbus_writeb(sbus_readb(AUXREG) | \
			    (AUXIO_ORMEIN | AUXIO_FLPY_DSEL), \
			    AUXREG); \
} while(0)
#define FLPY_MOTOROFF	\
do {	if (AUXREG) \
		sbus_writeb((sbus_readb(AUXREG) | \
			     AUXIO_ORMEIN) & (~AUXIO_FLPY_DSEL), \
			    AUXREG); \
} while(0)
#define FLPY_TCNTON	\
do {	if (AUXREG) \
		sbus_writeb((sbus_readb(AUXREG) | \
			     AUXIO_ORMEIN) | AUXIO_FLPY_TCNT, \
			    AUXREG); \
} while(0)
#define FLPY_TCNTOFF	\
do {	if (AUXREG) \
		sbus_writeb((sbus_readb(AUXREG) | \
			     AUXIO_ORMEIN) & (~AUXIO_FLPY_TCNT), \
			    AUXREG); \
} while(0)

#ifndef __ASSEMBLY__
extern __inline__ void set_auxio(unsigned char bits_on, unsigned char bits_off)
{
	unsigned char regval;
	unsigned long flags;

	save_flags(flags); cli();

	if(AUXREG) {
		unsigned char newval;

		regval = sbus_readb(AUXREG);
		newval  = regval | bits_on;
		newval &= ~bits_off;
		newval |= AUXIO_ORMEIN4M;
		sbus_writeb(newval, AUXREG);
	}
	restore_flags(flags);
}
#endif /* !(__ASSEMBLY__) */


/* AUXIO2 (Power Off Control) */
extern __volatile__ unsigned char * auxio_power_register;

#define	AUXIO_POWER_DETECT_FAILURE	32
#define	AUXIO_POWER_CLEAR_FAILURE	2
#define	AUXIO_POWER_OFF			1


#endif /* !(_SPARC_AUXIO_H) */