--- zzzz-none-000/linux-2.4.17/include/asm-ppc/serial.h 2001-11-03 01:43:54.000000000 +0000 +++ sangam-fb-322/linux-2.4.17/include/asm-ppc/serial.h 2004-11-24 13:21:50.000000000 +0000 @@ -1,5 +1,5 @@ /* - * BK Id: SCCS/s.serial.h 1.15 10/23/01 08:09:35 trini + * BK Id: SCCS/s.serial.h 1.26 11/28/01 10:22:04 paulus */ /* * include/asm-ppc/serial.h @@ -11,130 +11,43 @@ #include -#ifdef CONFIG_GEMINI -#include +#if defined(CONFIG_EV64260) +#include +#elif defined(CONFIG_GEMINI) +#include +#elif defined(CONFIG_POWERPMC250) +#include +#elif defined(CONFIG_LOPEC) +#include +#elif defined(CONFIG_MCPN765) +#include +#elif defined(CONFIG_MVME5100) +#include +#elif defined(CONFIG_PRPMC750) +#include +#elif defined(CONFIG_PRPMC800) +#include +#elif defined(CONFIG_SANDPOINT) +#include +#elif defined(CONFIG_SPRUCE) +#include +#elif defined(CONFIG_ZX4500) +#include #elif defined(CONFIG_4xx) -#include +#include #else /* - * This assumes you have a 1.8432 MHz clock for your UART. - * - * It'd be nice if someone built a serial card with a 24.576 MHz - * clock, since the 16550A is capable of handling a top speed of 1.5 - * megabits/second; but this requires the faster clock. + * XXX Assume for now it has PC-style ISA serial ports. + * This is true for PReP and CHRP at least. */ -#define BASE_BAUD ( 1843200 / 16 ) +#include +#include -#ifdef CONFIG_SERIAL_MANY_PORTS -#define RS_TABLE_SIZE 64 -#else -#define RS_TABLE_SIZE 4 -#endif - -/* Standard COM flags (except for COM4, because of the 8514 problem) */ -#ifdef CONFIG_SERIAL_DETECT_IRQ -#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ) -#define STD_COM4_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_AUTO_IRQ) -#else -#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST) -#define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF -#endif - -#ifdef CONFIG_SERIAL_MANY_PORTS -#define FOURPORT_FLAGS ASYNC_FOURPORT -#define ACCENT_FLAGS 0 -#define BOCA_FLAGS 0 -#define HUB6_FLAGS 0 -#endif - -/* - * The following define the access methods for the HUB6 card. All - * access is through two ports for all 24 possible chips. The card is - * selected through the high 2 bits, the port on that card with the - * "middle" 3 bits, and the register on that port with the bottom - * 3 bits. - * - * While the access port and interrupt is configurable, the default - * port locations are 0x302 for the port control register, and 0x303 - * for the data read/write register. Normally, the interrupt is at irq3 - * but can be anything from 3 to 7 inclusive. Note that using 3 will - * require disabling com2. - */ - -#define C_P(card,port) (((card)<<6|(port)<<3) + 1) - -#define STD_SERIAL_PORT_DEFNS \ - /* UART CLK PORT IRQ FLAGS */ \ - { 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \ - { 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \ - { 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \ - { 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */ - - -#ifdef CONFIG_SERIAL_MANY_PORTS -#define EXTRA_SERIAL_PORT_DEFNS \ - { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \ - { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \ - { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \ - { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \ - { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \ - { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \ - { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \ - { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \ - { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \ - { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \ - { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \ - { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \ - { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \ - { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \ - { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \ - { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \ - { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \ - { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \ - { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \ - { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \ - { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \ - { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \ - { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \ - { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \ - { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \ - { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \ - { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \ - { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */ -#else -#define EXTRA_SERIAL_PORT_DEFNS +#if defined(CONFIG_MAC_SERIAL) +#define SERIAL_DEV_OFFSET ((_machine == _MACH_prep || _machine == _MACH_chrp) ? 0 : 2) #endif -/* You can have up to four HUB6's in the system, but I've only - * included two cards here for a total of twelve ports. - */ -#if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS)) -#define HUB6_SERIAL_PORT_DFNS \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) }, /* ttyS32 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) }, /* ttyS33 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) }, /* ttyS34 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) }, /* ttyS35 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) }, /* ttyS36 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) }, /* ttyS37 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) }, /* ttyS38 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) }, /* ttyS39 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) }, /* ttyS40 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) }, /* ttyS41 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) }, /* ttyS42 */ \ - { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) }, /* ttyS43 */ -#else -#define HUB6_SERIAL_PORT_DFNS -#endif - -#define MCA_SERIAL_PORT_DFNS - -#define SERIAL_PORT_DFNS \ - STD_SERIAL_PORT_DEFNS \ - EXTRA_SERIAL_PORT_DEFNS \ - HUB6_SERIAL_PORT_DFNS \ - MCA_SERIAL_PORT_DFNS - #endif /* !CONFIG_GEMINI and others */ #endif /* __ASM_SERIAL_H__ */ #endif /* __KERNEL__ */