--- zzzz-none-000/linux-4.4.60/drivers/hwtracing/coresight/Kconfig	2017-04-08 07:53:53.000000000 +0000
+++ scorpion-1750e-727/linux-4.4.60/drivers/hwtracing/coresight/Kconfig	2021-02-04 17:41:59.000000000 +0000
@@ -12,6 +12,24 @@
 	  trace source gets enabled.
 
 if CORESIGHT
+
+config CORESIGHT_EVENT
+        tristate "CoreSight Event driver"
+	depends on TRACEPOINTS
+        help
+          This driver provides support for registering with various events
+          and performing CoreSight actions like aborting trace on their
+          occurrence. These events can be controlled by using module
+          parameters.
+
+config CORESIGHT_CSR
+	bool "CoreSight Slave Register driver"
+	help
+	  This driver provides support for CoreSight Slave Register block
+	  that hosts miscellaneous configuration registers.
+	  Those configuration registers can be used to control, various
+	  coresight configurations.
+
 config CORESIGHT_LINKS_AND_SINKS
 	bool "CoreSight Link and Sink drivers"
 	help
@@ -23,6 +41,7 @@
 config CORESIGHT_LINK_AND_SINK_TMC
 	bool "Coresight generic TMC driver"
 	depends on CORESIGHT_LINKS_AND_SINKS
+	select CORESIGHT_CSR
 	help
 	  This enables support for the Trace Memory Controller driver.
 	  Depending on its configuration the device can act as a link (embedded
@@ -61,7 +80,6 @@
 
 config CORESIGHT_SOURCE_ETM4X
 	bool "CoreSight Embedded Trace Macrocell 4.x driver"
-	depends on ARM64
 	select CORESIGHT_LINKS_AND_SINKS
 	help
 	  This driver provides support for the ETM4.x tracer module, tracing the
@@ -69,6 +87,22 @@
 	  for instruction level tracing. Depending on the implemented version
 	  data tracing may also be available.
 
+config CORESIGHT_REMOTE_ETM
+	bool "Remote processor ETM trace support"
+	depends on MSM_QMI_INTERFACE
+	help
+	  Enables support for ETM trace collection on remote processor using
+	  CoreSight framework. Enabling this will allow turning on ETM
+	  tracing on remote processor via sysfs by configuring the required
+	  CoreSight components.
+
+config CORESIGHT_REMOTE_ETM_DEFAULT_ENABLE
+	int "default enable bits for Remote processor ETM"
+	depends on CORESIGHT_REMOTE_ETM
+	help
+	  Support for enabling separated Remote processor ETM tracing. Depends
+	  on if instance id bit is set.
+
 config CORESIGHT_QCOM_REPLICATOR
 	bool "Qualcomm CoreSight Replicator driver"
 	depends on CORESIGHT_LINKS_AND_SINKS
@@ -77,4 +111,72 @@
 	  programmable ATB replicator sends the ATB trace stream from the
 	  ETB/ETF to the TPIUi and ETR.
 
+config CORESIGHT_STM
+	bool "CoreSight System Trace Macrocell driver"
+	select CORESIGHT_LINKS_AND_SINKS
+	help
+	  This driver provides support for hardware assisted software
+	  instrumentation based tracing. This is primarily useful for
+	  logging useful software events or data.
+
+config CORESIGHT_HWEVENT
+	bool "CoreSight Hardware Event driver"
+	depends on CORESIGHT_STM
+	select CORESIGHT_CSR
+	help
+	  This driver provides support for monitoring and tracing CoreSight
+	  Hardware Event across STM interface. It configures Coresight
+	  Hardware Event mux control registers to select hardware events
+	  based on user input.
+
+config CORESIGHT_CTI
+	bool "CoreSight Cross Trigger Interface driver"
+	help
+	  This driver provides support for Cross Trigger Interface that is
+	  used to input or output i.e. pass cross trigger events from one
+	  hardware component to another. It can also be used to pass
+	  software generated events.
+
+config CORESIGHT_TPDA
+	bool "CoreSight Trace, Profiling & Diagnostics Aggregator driver"
+	help
+	  This driver provides support for configuring aggregator. This is
+	  primarily useful for pulling the data sets from one or more
+	  attached monitors and pushing the resultant data out. Multiple
+	  monitors are connected on different input ports of TPDA.
+
+config CORESIGHT_TPDM
+	bool "CoreSight Trace, Profiling & Diagnostics Monitor driver"
+	help
+	  This driver provides support for configuring monitor. Monitors are
+	  primarily responsible for data set collection and support the
+	  ability to collect any permutation of data set types. Monitors are
+	  also responsible for interaction with system cross triggering.
+
+config CORESIGHT_TPDM_DEFAULT_ENABLE
+	bool "Turn on TPDM tracing by default"
+	depends on CORESIGHT_TPDM
+	help
+	  Turns on CoreSight TPDM tracing for different data set types by
+	  default. Otherwise, tracing is disabled by default but can be
+	  enabled via sysfs.
+
+	  If unsure, say 'N' here to avoid potential power and performance
+	  penalty.
+
+config CORESIGHT_QPDI
+	bool "CoreSight PMIC debug interface support"
+	help
+	  This driver provides support for controlling the PMIC debug interface
+	  feature. When enabled via sysfs it allows disagnostic access to the
+	  PMIC. Similarly this debug feature can be disabled via sysfs which
+	  prevents debug dongle detection.
+
+config CORESIGHT_SOURCE_DUMMY
+	bool "Dummy source support"
+	help
+	  Enables support for dummy source devices. Dummy source driver can be
+	  used for CoreSight sources that are owned and configured by some other
+	  subsystem and use Linux drivers to configure rest of trace path.
+
 endif