--- zzzz-none-000/linux-3.10.107/Documentation/devicetree/bindings/mmc/mmc.txt	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/Documentation/devicetree/bindings/mmc/mmc.txt	2021-02-04 17:41:59.000000000 +0000
@@ -21,13 +21,33 @@
   below for the case, when a GPIO is used for the CD line
 - wp-inverted: when present, polarity on the WP line is inverted. See the note
   below for the case, when a GPIO is used for the WP line
+- disable-wp: When set no physical WP line is present. This property should
+  only be specified when the controller has a dedicated write-protect
+  detection logic. If a GPIO is always used for the write-protect detection
+  logic it is sufficient to not specify wp-gpios property in the absence of a WP
+  line.
 - max-frequency: maximum operating clock frequency
 - no-1-8-v: when present, denotes that 1.8v card voltage is not supported on
   this system, even if the controller claims it is.
 - cap-sd-highspeed: SD high-speed timing is supported
 - cap-mmc-highspeed: MMC high-speed timing is supported
+- sd-uhs-sdr12: SD UHS SDR12 speed is supported
+- sd-uhs-sdr25: SD UHS SDR25 speed is supported
+- sd-uhs-sdr50: SD UHS SDR50 speed is supported
+- sd-uhs-sdr104: SD UHS SDR104 speed is supported
+- sd-uhs-ddr50: SD UHS DDR50 speed is supported
 - cap-power-off-card: powering off the card is safe
+- cap-mmc-hw-reset: eMMC hardware reset is supported
 - cap-sdio-irq: enable SDIO IRQ signalling on this interface
+- full-pwr-cycle: full power cycle of the card is supported
+- mmc-ddr-1_8v: eMMC high-speed DDR mode(1.8V I/O) is supported
+- mmc-ddr-1_2v: eMMC high-speed DDR mode(1.2V I/O) is supported
+- mmc-hs200-1_8v: eMMC HS200 mode(1.8V I/O) is supported
+- mmc-hs200-1_2v: eMMC HS200 mode(1.2V I/O) is supported
+- mmc-hs400-1_8v: eMMC HS400 mode(1.8V I/O) is supported
+- mmc-hs400-1_2v: eMMC HS400 mode(1.2V I/O) is supported
+- dsr: Value the card's (optional) Driver Stage Register (DSR) should be
+  programmed with. Valid range: [0 .. 0xffff].
 
 *NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line
 polarity properties, we have to fix the meaning of the "normal" and "inverted"
@@ -48,9 +68,46 @@
 
 Optional SDIO properties:
 - keep-power-in-suspend: Preserves card power during a suspend/resume cycle
-- enable-sdio-wakeup: Enables wake up of host system on SDIO IRQ assertion
+- wakeup-source: Enables wake up of host system on SDIO IRQ assertion
+		 (Legacy property supported: "enable-sdio-wakeup")
 
-Example:
+
+MMC power sequences:
+--------------------
+
+System on chip designs may specify a specific MMC power sequence. To
+successfully detect an (e)MMC/SD/SDIO card, that power sequence must be
+maintained while initializing the card.
+
+Optional property:
+- mmc-pwrseq: phandle to the MMC power sequence node. See "mmc-pwrseq-*"
+	for documentation of MMC power sequence bindings.
+
+
+Use of Function subnodes
+------------------------
+
+On embedded systems the cards connected to a host may need additional
+properties. These can be specified in subnodes to the host controller node.
+The subnodes are identified by the standard 'reg' property.
+Which information exactly can be specified depends on the bindings for the
+SDIO function driver for the subnode, as specified by the compatible string.
+
+Required host node properties when using function subnodes:
+- #address-cells: should be one. The cell is the slot id.
+- #size-cells: should be zero.
+
+Required function subnode properties:
+- compatible: name of SDIO function following generic names recommended practice
+- reg: Must contain the SDIO function number of the function this subnode
+       describes. A value of 0 denotes the memory SD function, values from
+       1 to 7 denote the SDIO functions.
+
+
+Examples
+--------
+
+Basic example:
 
 sdhci@ab000000 {
 	compatible = "sdhci";
@@ -62,5 +119,29 @@
 	wp-gpios = <&gpio 70 0>;
 	max-frequency = <50000000>;
 	keep-power-in-suspend;
-	enable-sdio-wakeup;
+	wakeup-source;
+	mmc-pwrseq = <&sdhci0_pwrseq>
 }
+
+Example with sdio function subnode:
+
+mmc3: mmc@01c12000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc3_pins_a>;
+	vmmc-supply = <&reg_vmmc3>;
+	bus-width = <4>;
+	non-removable;
+	mmc-pwrseq = <&sdhci0_pwrseq>
+	status = "okay";
+
+	brcmf: bcrmf@1 {
+		reg = <1>;
+		compatible = "brcm,bcm43xx-fmac";
+		interrupt-parent = <&pio>;
+		interrupts = <10 8>; /* PH10 / EINT10 */
+		interrupt-names = "host-wake";
+	};
+};