--- zzzz-none-000/linux-3.10.107/Documentation/devicetree/bindings/net/cpsw.txt	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/Documentation/devicetree/bindings/net/cpsw.txt	2021-02-04 17:41:59.000000000 +0000
@@ -2,7 +2,11 @@
 ------------------------------------------------------
 
 Required properties:
-- compatible		: Should be "ti,cpsw"
+- compatible		: Should be one of the below:-
+			  "ti,cpsw" for backward compatible
+			  "ti,am335x-cpsw" for AM335x controllers
+			  "ti,am4372-cpsw" for AM437x controllers
+			  "ti,dra7-cpsw" for DRA7x controllers
 - reg			: physical base address and size of the cpsw
 			  registers map
 - interrupts		: property with a value describing the interrupt
@@ -24,14 +28,30 @@
 - ti,hwmods		: Must be "cpgmac0"
 - no_bd_ram		: Must be 0 or 1
 - dual_emac		: Specifies Switch to act as Dual EMAC
+- syscon		: Phandle to the system control device node, which is
+			  the control module device of the am33x
+- mode-gpios		: Should be added if one/multiple gpio lines are
+			  required to be driven so that cpsw data lines
+			  can be connected to the phy via selective mux.
+			  For example in dra72x-evm, pcf gpio has to be
+			  driven low so that cpsw slave 0 and phy data
+			  lines are connected via mux.
+
 
 Slave Properties:
 Required properties:
-- phy_id		: Specifies slave phy id
-- mac-address		: Specifies slave MAC address
+- phy-mode		: See ethernet.txt file in the same directory
 
 Optional properties:
 - dual_emac_res_vlan	: Specifies VID to be used to segregate the ports
+- mac-address		: See ethernet.txt file in the same directory
+- phy_id		: Specifies slave phy id
+- phy-handle		: See ethernet.txt file in the same directory
+
+Slave sub-nodes:
+- fixed-link		: See fixed-link.txt file in the same directory
+			  Either the property phy_id, or the sub-node
+			  fixed-link can be specified
 
 Note: "ti,hwmods" field is used to fetch the base address and irq
 resources from TI, omap hwmod data base during device registration.
@@ -56,13 +76,16 @@
 		active_slave = <0>;
 		cpts_clock_mult = <0x80000000>;
 		cpts_clock_shift = <29>;
+		syscon = <&cm>;
 		cpsw_emac0: slave@0 {
 			phy_id = <&davinci_mdio>, <0>;
+			phy-mode = "rgmii-txid";
 			/* Filled in by U-Boot */
 			mac-address = [ 00 00 00 00 00 00 ];
 		};
 		cpsw_emac1: slave@1 {
 			phy_id = <&davinci_mdio>, <1>;
+			phy-mode = "rgmii-txid";
 			/* Filled in by U-Boot */
 			mac-address = [ 00 00 00 00 00 00 ];
 		};
@@ -82,13 +105,16 @@
 		active_slave = <0>;
 		cpts_clock_mult = <0x80000000>;
 		cpts_clock_shift = <29>;
+		syscon = <&cm>;
 		cpsw_emac0: slave@0 {
 			phy_id = <&davinci_mdio>, <0>;
+			phy-mode = "rgmii-txid";
 			/* Filled in by U-Boot */
 			mac-address = [ 00 00 00 00 00 00 ];
 		};
 		cpsw_emac1: slave@1 {
 			phy_id = <&davinci_mdio>, <1>;
+			phy-mode = "rgmii-txid";
 			/* Filled in by U-Boot */
 			mac-address = [ 00 00 00 00 00 00 ];
 		};