--- zzzz-none-000/linux-3.10.107/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt	2021-02-04 17:41:59.000000000 +0000
@@ -8,7 +8,16 @@
 Required properties:
   - reg : Offset and length of the register set for the device
   - compatible : Should define the compatible device type for the
-    mdio.  Currently, this is most likely to be "fsl,gianfar-mdio"
+    mdio. Currently supported strings/devices are:
+	- "fsl,gianfar-tbi"
+	- "fsl,gianfar-mdio"
+	- "fsl,etsec2-tbi"
+	- "fsl,etsec2-mdio"
+	- "fsl,ucc-mdio"
+	- "fsl,fman-mdio"
+    When device_type is "mdio", the following strings are also considered:
+	- "gianfar"
+	- "ucc_geth_phy"
 
 Example:
 
@@ -38,24 +47,20 @@
   - model : Model of the device.  Can be "TSEC", "eTSEC", or "FEC"
   - compatible : Should be "gianfar"
   - reg : Offset and length of the register set for the device
-  - local-mac-address : List of bytes representing the ethernet address of
-    this controller
   - interrupts : For FEC devices, the first interrupt is the device's
     interrupt.  For TSEC and eTSEC devices, the first interrupt is
     transmit, the second is receive, and the third is error.
-  - phy-handle : The phandle for the PHY connected to this ethernet
-    controller.
-  - fixed-link : <a b c d e> where a is emulated phy id - choose any,
-    but unique to the all specified fixed-links, b is duplex - 0 half,
-    1 full, c is link speed - d#10/d#100/d#1000, d is pause - 0 no
-    pause, 1 pause, e is asym_pause - 0 no asym_pause, 1 asym_pause.
-  - phy-connection-type : a string naming the controller/PHY interface type,
-    i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "sgmii",
-    "tbi", or "rtbi".  This property is only really needed if the connection
-    is of type "rgmii-id", as all other connection types are detected by
-    hardware.
+  - phy-handle : See ethernet.txt file in the same directory.
+  - fixed-link : See fixed-link.txt in the same directory.
+  - phy-connection-type : See ethernet.txt file in the same directory.
+    This property is only really needed if the connection is of type
+    "rgmii-id", as all other connection types are detected by hardware.
   - fsl,magic-packet : If present, indicates that the hardware supports
     waking up via magic packet.
+  - fsl,wake-on-filer : If present, indicates that the hardware supports
+    waking up by Filer General Purpose Interrupt (FGPI) asserted on the
+    Rx int line.  This is an advanced power management capability allowing
+    certain packet types (user) defined by filer rules to wake up the system.
   - bd-stash : If present, indicates that the hardware supports stashing
     buffer descriptors in the L2.
   - rx-stash-len : Denotes the number of bytes of a received buffer to stash
@@ -86,6 +91,7 @@
 
 Clock Properties:
 
+  - fsl,cksel        Timer reference clock source.
   - fsl,tclk-period  Timer reference clock period in nanoseconds.
   - fsl,tmr-prsc     Prescaler, divides the output clock.
   - fsl,tmr-add      Frequency compensation value.
@@ -97,7 +103,7 @@
   clock. You must choose these carefully for the clock to work right.
   Here is how to figure good values:
 
-  TimerOsc     = system clock               MHz
+  TimerOsc     = selected reference clock   MHz
   tclk_period  = desired clock period       nanoseconds
   NominalFreq  = 1000 / tclk_period         MHz
   FreqDivRatio = TimerOsc / NominalFreq     (must be greater that 1.0)
@@ -114,6 +120,20 @@
   Pulse Per Second (PPS) signal, since this will be offered to the PPS
   subsystem to synchronize the Linux clock.
 
+  Reference clock source is determined by the value, which is holded
+  in CKSEL bits in TMR_CTRL register. "fsl,cksel" property keeps the
+  value, which will be directly written in those bits, that is why,
+  according to reference manual, the next clock sources can be used:
+
+  <0> - external high precision timer reference clock (TSEC_TMR_CLK
+        input is used for this purpose);
+  <1> - eTSEC system clock;
+  <2> - eTSEC1 transmit clock;
+  <3> - RTC clock input.
+
+  When this attribute is not used, eTSEC system clock will serve as
+  IEEE 1588 timer reference clock.
+
 Example:
 
 	ptp_clock@24E00 {
@@ -121,6 +141,7 @@
 		reg = <0x24E00 0xB0>;
 		interrupts = <12 0x8 13 0x8>;
 		interrupt-parent = < &ipic >;
+		fsl,cksel       = <1>;
 		fsl,tclk-period = <10>;
 		fsl,tmr-prsc    = <100>;
 		fsl,tmr-add     = <0x999999A4>;