--- zzzz-none-000/linux-3.10.107/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt	2021-02-04 17:41:59.000000000 +0000
@@ -18,7 +18,8 @@
   pin functions is ignored
 
 - pinctrl-single,bit-per-mux : boolean to indicate that one register controls
-  more than one pin
+  more than one pin, for which "pinctrl-single,function-mask" property specifies
+ position mask of pin.
 
 - pinctrl-single,drive-strength : array of value that are used to configure
   drive strength in the pinmux register. They're value of drive strength
@@ -62,6 +63,13 @@
 		/* input, enable bits, disable bits, mask */
 		pinctrl-single,input-schmitt-enable = <0x30 0x40 0 0x70>;
 
+- pinctrl-single,low-power-mode : array of value that are used to configure
+  low power mode of this pin. For some silicons, the low power mode will
+  control the output of the pin when the pad including the pin enter low
+  power mode.
+		/* low power mode value, mask */
+		pinctrl-single,low-power-mode = <0x288 0x388>;
+
 - pinctrl-single,gpio-range : list of value that are used to configure a GPIO
   range. They're value of subnode phandle, pin base in pinctrl device, pin
   number in this range, GPIO function value of this GPIO range.
@@ -71,6 +79,13 @@
 		/* pin base, nr pins & gpio function */
 		pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1>;
 
+- interrupt-controller : standard interrupt controller binding if using
+  interrupts for wake-up events for example. In this case pinctrl-single
+  is set up as a chained interrupt controller and the wake-up interrupts
+  can be requested by the drivers using request_irq().
+
+- #interrupt-cells : standard interrupt binding if using interrupts
+
 This driver assumes that there is only one register for each pin (unless the
 pinctrl-single,bit-per-mux is set), and uses the common pinctrl bindings as
 specified in the pinctrl-bindings.txt document in this directory.
@@ -90,7 +105,7 @@
 In case when one register changes more than one pin's mux the
 pinctrl-single,bits need to be used which takes three parameters:
 
-	pinctrl-single,bits = <0xdc 0x18, 0xff>;
+	pinctrl-single,bits = <0xdc 0x18 0xff>;
 
 Where 0xdc is the offset from the pinctrl register base address for the
 device pinctrl register, 0x18 is the desired value, and 0xff is the sub mask to
@@ -120,6 +135,8 @@
 	reg = <0x4a100040 0x0196>;
 	#address-cells = <1>;
 	#size-cells = <0>;
+	#interrupt-cells = <1>;
+	interrupt-controller;
 	pinctrl-single,register-width = <16>;
 	pinctrl-single,function-mask = <0xffff>;
 };
@@ -130,6 +147,8 @@
 	reg = <0x4a31e040 0x0038>;
 	#address-cells = <1>;
 	#size-cells = <0>;
+	#interrupt-cells = <1>;
+	interrupt-controller;
 	pinctrl-single,register-width = <16>;
 	pinctrl-single,function-mask = <0xffff>;
 };