--- zzzz-none-000/linux-3.10.107/Documentation/devicetree/bindings/usb/dwc3.txt	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/Documentation/devicetree/bindings/usb/dwc3.txt	2021-02-04 17:41:59.000000000 +0000
@@ -1,20 +1,56 @@
 synopsys DWC3 CORE
 
-DWC3- USB3 CONTROLLER
+DWC3- USB3 CONTROLLER. Complies to the generic USB binding properties
+      as described in 'usb/generic.txt'
 
 Required properties:
- - compatible: must be "synopsys,dwc3"
+ - compatible: must be "snps,dwc3"
  - reg : Address and length of the register set for the device
  - interrupts: Interrupts used by the dwc3 controller.
- - usb-phy : array of phandle for the PHY device
 
 Optional properties:
+ - usb-phy : array of phandle for the PHY device.  The first element
+   in the array is expected to be a handle to the USB2/HS PHY and
+   the second element is expected to be a handle to the USB3/SS PHY
+ - phys: from the *Generic PHY* bindings
+ - phy-names: from the *Generic PHY* bindings
  - tx-fifo-resize: determines if the FIFO *has* to be reallocated.
+ - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable
+ - snps,disable_scramble_quirk: true when SW should disable data scrambling.
+	Only really useful for FPGA builds.
+ - snps,has-lpm-erratum: true when DWC3 was configured with LPM Erratum enabled
+ - snps,lpm-nyet-threshold: LPM NYET threshold
+ - snps,u2exit_lfps_quirk: set if we want to enable u2exit lfps quirk
+ - snps,u2ss_inp3_quirk: set if we enable P3 OK for U2/SS Inactive quirk
+ - snps,req_p1p2p3_quirk: when set, the core will always request for
+			P1/P2/P3 transition sequence.
+ - snps,del_p1p2p3_quirk: when set core will delay P1/P2/P3 until a certain
+			amount of 8B10B errors occur.
+ - snps,del_phy_power_chg_quirk: when set core will delay PHY power change
+			from P0 to P1/P2/P3.
+ - snps,lfps_filter_quirk: when set core will filter LFPS reception.
+ - snps,rx_detect_poll_quirk: when set core will disable a 400us delay to start
+			Polling LFPS after RX.Detect.
+ - snps,tx_de_emphasis_quirk: when set core will set Tx de-emphasis value.
+ - snps,tx_de_emphasis: the value driven to the PHY is controlled by the
+			LTSSM during USB3 Compliance mode.
+ - snps,dis_u3_susphy_quirk: when set core will disable USB3 suspend phy.
+ - snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy.
+ - snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG,
+			disabling the suspend signal to the PHY.
+ - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal
+			utmi_l1_suspend_n, false when asserts utmi_sleep_n
+ - snps,hird-threshold: HIRD threshold
+ - snps,hsphy_interface: High-Speed PHY interface selection between "utmi" for
+   UTMI+ and "ulpi" for ULPI when the DWC_USB3_HSPHY_INTERFACE has value 3.
+ - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ
+	register for post-silicon frame length adjustment when the
+	fladj_30mhz_sdbnd signal is invalid or incorrect.
 
 This is usually a subnode to DWC3 glue to which it is connected.
 
 dwc3@4a030000 {
-	compatible = "synopsys,dwc3";
+	compatible = "snps,dwc3";
 	reg = <0x4a030000 0xcfff>;
 	interrupts = <0 92 4>
 	usb-phy = <&usb2_phy>, <&usb3,phy>;