--- zzzz-none-000/linux-3.10.107/Documentation/leds/leds-lp55xx.txt	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/Documentation/leds/leds-lp55xx.txt	2021-02-04 17:41:59.000000000 +0000
@@ -1,11 +1,11 @@
-LP5521/LP5523/LP55231 Common Driver
-===================================
+LP5521/LP5523/LP55231/LP5562/LP8501 Common Driver
+=================================================
 
 Authors: Milo(Woogyom) Kim <milo.kim@ti.com>
 
 Description
 -----------
-LP5521, LP5523/55231 and LP5562 have common features as below.
+LP5521, LP5523/55231, LP5562 and LP8501 have common features as below.
 
   Register access via the I2C
   Device initialization/deinitialization
@@ -73,6 +73,10 @@
 run_engine    : Start program which is loaded via the firmware interface
 firmware      : Load program data
 
+In case of LP5523, one more command is required, 'enginex_leds'.
+It is used for selecting LED output(s) at each engine number.
+In more details, please refer to 'leds-lp5523.txt'.
+
 For example, run blinking pattern in engine #1 of LP5521
 echo 1 > /sys/bus/i2c/devices/xxxx/select_engine
 echo 1 > /sys/class/firmware/lp5521/loading
@@ -81,10 +85,12 @@
 echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
 
 For example, run blinking pattern in engine #3 of LP55231
+Two LEDs are configured as pattern output channels.
 echo 3 > /sys/bus/i2c/devices/xxxx/select_engine
 echo 1 > /sys/class/firmware/lp55231/loading
 echo "9d0740ff7e0040007e00a0010000" > /sys/class/firmware/lp55231/data
 echo 0 > /sys/class/firmware/lp55231/loading
+echo "000001100" > /sys/bus/i2c/devices/xxxx/engine3_leds
 echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
 
 To start blinking patterns in engine #2 and #3 simultaneously,
@@ -99,16 +105,42 @@
 echo 1 > /sys/class/leds/red/device/run_engine
 
 Here is another example for LP5523.
+Full LED strings are selected by 'engine2_leds'.
 echo 2 > /sys/bus/i2c/devices/xxxx/select_engine
 echo 1 > /sys/class/firmware/lp5523/loading
 echo "9d80400004ff05ff437f0000" > /sys/class/firmware/lp5523/data
 echo 0 > /sys/class/firmware/lp5523/loading
+echo "111111111" > /sys/bus/i2c/devices/xxxx/engine2_leds
 echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
 
 As soon as 'loading' is set to 0, registered callback is called.
 Inside the callback, the selected engine is loaded and memory is updated.
 To run programmed pattern, 'run_engine' attribute should be enabled.
 
+The pattern sqeuence of LP8501 is similar to LP5523.
+However pattern data is specific.
+Ex 1) Engine 1 is used
+echo 1 > /sys/bus/i2c/devices/xxxx/select_engine
+echo 1 > /sys/class/firmware/lp8501/loading
+echo "9d0140ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
+echo 0 > /sys/class/firmware/lp8501/loading
+echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+Ex 2) Engine 2 and 3 are used at the same time
+echo 2 > /sys/bus/i2c/devices/xxxx/select_engine
+sleep 1
+echo 1 > /sys/class/firmware/lp8501/loading
+echo "9d0140ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
+echo 0 > /sys/class/firmware/lp8501/loading
+sleep 1
+echo 3 > /sys/bus/i2c/devices/xxxx/select_engine
+sleep 1
+echo 1 > /sys/class/firmware/lp8501/loading
+echo "9d0340ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
+echo 0 > /sys/class/firmware/lp8501/loading
+sleep 1
+echo 1 > /sys/class/leds/d1/device/run_engine
+
 ( 'run_engine' and 'firmware_cb' )
 The sequence of running the program data is common.
 But each device has own specific register addresses for commands.