--- zzzz-none-000/linux-3.10.107/arch/arm/boot/dts/am33xx.dtsi 2017-06-27 09:49:32.000000000 +0000 +++ scorpion-7490-727/linux-3.10.107/arch/arm/boot/dts/am33xx.dtsi 2021-02-04 17:41:59.000000000 +0000 @@ -8,26 +8,42 @@ * kind, whether express or implied. */ -/include/ "skeleton.dtsi" +#include +#include + +#include "skeleton.dtsi" / { compatible = "ti,am33xx"; interrupt-parent = <&intc>; aliases { - serial0 = &uart1; - serial1 = &uart2; - serial2 = &uart3; - serial3 = &uart4; - serial4 = &uart5; - serial5 = &uart6; + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + serial4 = &uart4; + serial5 = &uart5; d_can0 = &dcan0; d_can1 = &dcan1; + usb0 = &usb0; + usb1 = &usb1; + phy0 = &usb0_phy; + phy1 = &usb1_phy; + ethernet0 = &cpsw_emac0; + ethernet1 = &cpsw_emac1; }; cpus { + #address-cells = <1>; + #size-cells = <0>; cpu@0 { compatible = "arm,cortex-a8"; + device_type = "cpu"; + reg = <0>; /* * To consider voltage drop between PMIC and SoC, @@ -42,12 +58,21 @@ 275000 1125000 >; voltage-tolerance = <2>; /* 2 percentage */ + + clocks = <&dpll_mpu_ck>; + clock-names = "cpu"; + clock-latency = <300000>; /* From omap-cpufreq driver */ }; }; + pmu { + compatible = "arm,cortex-a8-pmu"; + interrupts = <3>; + }; + /* - * The soc node represents the soc top level view. It is uses for IPs + * The soc node represents the soc top level view. It is used for IPs * that are not memory mapped in the MPU view or for the MPU itself. */ soc { @@ -58,19 +83,10 @@ }; }; - am33xx_pinmux: pinmux@44e10800 { - compatible = "pinctrl-single"; - reg = <0x44e10800 0x0238>; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-single,register-width = <32>; - pinctrl-single,function-mask = <0x7f>; - }; - /* * XXX: Use a flat representation of the AM33XX interconnect. - * The real AM33XX interconnect network is quite complex.Since - * that will not bring real advantage to represent that in DT + * The real AM33XX interconnect network is quite complex. Since + * it will not bring real advantage to represent that in DT * for the moment, just use a fake OCP bus entry to represent * the whole bus hierarchy. */ @@ -81,21 +97,98 @@ ranges; ti,hwmods = "l3_main"; + l4_wkup: l4_wkup@44c00000 { + compatible = "ti,am3-l4-wkup", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x44c00000 0x280000>; + + wkup_m3: wkup_m3@100000 { + compatible = "ti,am3352-wkup-m3"; + reg = <0x100000 0x4000>, + <0x180000 0x2000>; + reg-names = "umem", "dmem"; + ti,hwmods = "wkup_m3"; + ti,pm-firmware = "am335x-pm-firmware.elf"; + }; + + prcm: prcm@200000 { + compatible = "ti,am3-prcm"; + reg = <0x200000 0x4000>; + + prcm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + + prcm_clockdomains: clockdomains { + }; + }; + + scm: scm@210000 { + compatible = "ti,am3-scm", "simple-bus"; + reg = <0x210000 0x2000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x210000 0x2000>; + + am33xx_pinmux: pinmux@800 { + compatible = "pinctrl-single"; + reg = <0x800 0x238>; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0x7f>; + }; + + scm_conf: scm_conf@0 { + compatible = "syscon"; + reg = <0x0 0x800>; + #address-cells = <1>; + #size-cells = <1>; + + scm_clocks: clocks { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + + wkup_m3_ipc: wkup_m3_ipc@1324 { + compatible = "ti,am3352-wkup-m3-ipc"; + reg = <0x1324 0x24>; + interrupts = <78>; + ti,rproc = <&wkup_m3>; + mboxes = <&mailbox &mbox_wkupm3>; + }; + + scm_clockdomains: clockdomains { + }; + }; + }; + intc: interrupt-controller@48200000 { - compatible = "ti,omap2-intc"; + compatible = "ti,am33xx-intc"; interrupt-controller; #interrupt-cells = <1>; - ti,intc-size = <128>; reg = <0x48200000 0x1000>; }; + edma: edma@49000000 { + compatible = "ti,edma3"; + ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2"; + reg = <0x49000000 0x10000>, + <0x44e10f90 0x40>; + interrupts = <12 13 14>; + #dma-cells = <1>; + }; + gpio0: gpio@44e07000 { compatible = "ti,omap4-gpio"; ti,hwmods = "gpio1"; gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; reg = <0x44e07000 0x1000>; interrupts = <96>; }; @@ -106,7 +199,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; reg = <0x4804c000 0x1000>; interrupts = <98>; }; @@ -117,7 +210,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; reg = <0x481ac000 0x1000>; interrupts = <32>; }; @@ -128,40 +221,46 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; reg = <0x481ae000 0x1000>; interrupts = <62>; }; - uart1: serial@44e09000 { - compatible = "ti,omap3-uart"; + uart0: serial@44e09000 { + compatible = "ti,am3352-uart", "ti,omap3-uart"; ti,hwmods = "uart1"; clock-frequency = <48000000>; reg = <0x44e09000 0x2000>; interrupts = <72>; status = "disabled"; + dmas = <&edma 26>, <&edma 27>; + dma-names = "tx", "rx"; }; - uart2: serial@48022000 { - compatible = "ti,omap3-uart"; + uart1: serial@48022000 { + compatible = "ti,am3352-uart", "ti,omap3-uart"; ti,hwmods = "uart2"; clock-frequency = <48000000>; reg = <0x48022000 0x2000>; interrupts = <73>; status = "disabled"; + dmas = <&edma 28>, <&edma 29>; + dma-names = "tx", "rx"; }; - uart3: serial@48024000 { - compatible = "ti,omap3-uart"; + uart2: serial@48024000 { + compatible = "ti,am3352-uart", "ti,omap3-uart"; ti,hwmods = "uart3"; clock-frequency = <48000000>; reg = <0x48024000 0x2000>; interrupts = <74>; status = "disabled"; + dmas = <&edma 30>, <&edma 31>; + dma-names = "tx", "rx"; }; - uart4: serial@481a6000 { - compatible = "ti,omap3-uart"; + uart3: serial@481a6000 { + compatible = "ti,am3352-uart", "ti,omap3-uart"; ti,hwmods = "uart4"; clock-frequency = <48000000>; reg = <0x481a6000 0x2000>; @@ -169,8 +268,8 @@ status = "disabled"; }; - uart5: serial@481a8000 { - compatible = "ti,omap3-uart"; + uart4: serial@481a8000 { + compatible = "ti,am3352-uart", "ti,omap3-uart"; ti,hwmods = "uart5"; clock-frequency = <48000000>; reg = <0x481a8000 0x2000>; @@ -178,8 +277,8 @@ status = "disabled"; }; - uart6: serial@481aa000 { - compatible = "ti,omap3-uart"; + uart5: serial@481aa000 { + compatible = "ti,am3352-uart", "ti,omap3-uart"; ti,hwmods = "uart6"; clock-frequency = <48000000>; reg = <0x481aa000 0x2000>; @@ -217,6 +316,51 @@ status = "disabled"; }; + mmc1: mmc@48060000 { + compatible = "ti,omap4-hsmmc"; + ti,hwmods = "mmc1"; + ti,dual-volt; + ti,needs-special-reset; + ti,needs-special-hs-handling; + dmas = <&edma 24 + &edma 25>; + dma-names = "tx", "rx"; + interrupts = <64>; + interrupt-parent = <&intc>; + reg = <0x48060000 0x1000>; + status = "disabled"; + }; + + mmc2: mmc@481d8000 { + compatible = "ti,omap4-hsmmc"; + ti,hwmods = "mmc2"; + ti,needs-special-reset; + dmas = <&edma 2 + &edma 3>; + dma-names = "tx", "rx"; + interrupts = <28>; + interrupt-parent = <&intc>; + reg = <0x481d8000 0x1000>; + status = "disabled"; + }; + + mmc3: mmc@47810000 { + compatible = "ti,omap4-hsmmc"; + ti,hwmods = "mmc3"; + ti,needs-special-reset; + interrupts = <29>; + interrupt-parent = <&intc>; + reg = <0x47810000 0x1000>; + status = "disabled"; + }; + + hwspinlock: spinlock@480ca000 { + compatible = "ti,omap4-hwspinlock"; + reg = <0x480ca000 0x1000>; + ti,hwmods = "spinlock"; + #hwlock-cells = <1>; + }; + wdt2: wdt@44e35000 { compatible = "ti,omap3-wdt"; ti,hwmods = "wd_timer2"; @@ -224,24 +368,42 @@ interrupts = <91>; }; - dcan0: d_can@481cc000 { - compatible = "bosch,d_can"; + dcan0: can@481cc000 { + compatible = "ti,am3352-d_can"; ti,hwmods = "d_can0"; - reg = <0x481cc000 0x2000 - 0x44e10644 0x4>; + reg = <0x481cc000 0x2000>; + clocks = <&dcan0_fck>; + clock-names = "fck"; + syscon-raminit = <&scm_conf 0x644 0>; interrupts = <52>; status = "disabled"; }; - dcan1: d_can@481d0000 { - compatible = "bosch,d_can"; + dcan1: can@481d0000 { + compatible = "ti,am3352-d_can"; ti,hwmods = "d_can1"; - reg = <0x481d0000 0x2000 - 0x44e10644 0x4>; + reg = <0x481d0000 0x2000>; + clocks = <&dcan1_fck>; + clock-names = "fck"; + syscon-raminit = <&scm_conf 0x644 1>; interrupts = <55>; status = "disabled"; }; + mailbox: mailbox@480C8000 { + compatible = "ti,omap4-mailbox"; + reg = <0x480C8000 0x200>; + interrupts = <77>; + ti,hwmods = "mailbox"; + #mbox-cells = <1>; + ti,mbox-num-users = <4>; + ti,mbox-num-fifos = <8>; + mbox_wkupm3: wkup_m3 { + ti,mbox-tx = <0 0 0>; + ti,mbox-rx = <0 0 3>; + }; + }; + timer1: timer@44e31000 { compatible = "ti,am335x-timer-1ms"; reg = <0x44e31000 0x400>; @@ -296,8 +458,8 @@ ti,timer-pwm; }; - rtc@44e3e000 { - compatible = "ti,da830-rtc"; + rtc: rtc@44e3e000 { + compatible = "ti,am3352-rtc", "ti,da830-rtc"; reg = <0x44e3e000 0x1000>; interrupts = <75 76>; @@ -312,6 +474,11 @@ interrupts = <65>; ti,spi-num-cs = <2>; ti,hwmods = "spi0"; + dmas = <&edma 16 + &edma 17 + &edma 18 + &edma 19>; + dma-names = "tx0", "rx0", "tx1", "rx1"; status = "disabled"; }; @@ -323,29 +490,237 @@ interrupts = <125>; ti,spi-num-cs = <2>; ti,hwmods = "spi1"; + dmas = <&edma 42 + &edma 43 + &edma 44 + &edma 45>; + dma-names = "tx0", "rx0", "tx1", "rx1"; status = "disabled"; }; - usb@47400000 { - compatible = "ti,musb-am33xx"; - reg = <0x47400000 0x1000 /* usbss */ - 0x47401000 0x800 /* musb instance 0 */ - 0x47401800 0x800>; /* musb instance 1 */ - interrupts = <17 /* usbss */ - 18 /* musb instance 0 */ - 19>; /* musb instance 1 */ - multipoint = <1>; - num-eps = <16>; - ram-bits = <12>; - port0-mode = <3>; - port1-mode = <3>; - power = <250>; + usb: usb@47400000 { + compatible = "ti,am33xx-usb"; + reg = <0x47400000 0x1000>; + ranges; + #address-cells = <1>; + #size-cells = <1>; ti,hwmods = "usb_otg_hs"; + status = "disabled"; + + usb_ctrl_mod: control@44e10620 { + compatible = "ti,am335x-usb-ctrl-module"; + reg = <0x44e10620 0x10 + 0x44e10648 0x4>; + reg-names = "phy_ctrl", "wakeup"; + status = "disabled"; + }; + + usb0_phy: usb-phy@47401300 { + compatible = "ti,am335x-usb-phy"; + reg = <0x47401300 0x100>; + reg-names = "phy"; + status = "disabled"; + ti,ctrl_mod = <&usb_ctrl_mod>; + }; + + usb0: usb@47401000 { + compatible = "ti,musb-am33xx"; + status = "disabled"; + reg = <0x47401400 0x400 + 0x47401000 0x200>; + reg-names = "mc", "control"; + + interrupts = <18>; + interrupt-names = "mc"; + dr_mode = "otg"; + mentor,multipoint = <1>; + mentor,num-eps = <16>; + mentor,ram-bits = <12>; + mentor,power = <500>; + phys = <&usb0_phy>; + + dmas = <&cppi41dma 0 0 &cppi41dma 1 0 + &cppi41dma 2 0 &cppi41dma 3 0 + &cppi41dma 4 0 &cppi41dma 5 0 + &cppi41dma 6 0 &cppi41dma 7 0 + &cppi41dma 8 0 &cppi41dma 9 0 + &cppi41dma 10 0 &cppi41dma 11 0 + &cppi41dma 12 0 &cppi41dma 13 0 + &cppi41dma 14 0 &cppi41dma 0 1 + &cppi41dma 1 1 &cppi41dma 2 1 + &cppi41dma 3 1 &cppi41dma 4 1 + &cppi41dma 5 1 &cppi41dma 6 1 + &cppi41dma 7 1 &cppi41dma 8 1 + &cppi41dma 9 1 &cppi41dma 10 1 + &cppi41dma 11 1 &cppi41dma 12 1 + &cppi41dma 13 1 &cppi41dma 14 1>; + dma-names = + "rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7", + "rx8", "rx9", "rx10", "rx11", "rx12", "rx13", + "rx14", "rx15", + "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7", + "tx8", "tx9", "tx10", "tx11", "tx12", "tx13", + "tx14", "tx15"; + }; + + usb1_phy: usb-phy@47401b00 { + compatible = "ti,am335x-usb-phy"; + reg = <0x47401b00 0x100>; + reg-names = "phy"; + status = "disabled"; + ti,ctrl_mod = <&usb_ctrl_mod>; + }; + + usb1: usb@47401800 { + compatible = "ti,musb-am33xx"; + status = "disabled"; + reg = <0x47401c00 0x400 + 0x47401800 0x200>; + reg-names = "mc", "control"; + interrupts = <19>; + interrupt-names = "mc"; + dr_mode = "otg"; + mentor,multipoint = <1>; + mentor,num-eps = <16>; + mentor,ram-bits = <12>; + mentor,power = <500>; + phys = <&usb1_phy>; + + dmas = <&cppi41dma 15 0 &cppi41dma 16 0 + &cppi41dma 17 0 &cppi41dma 18 0 + &cppi41dma 19 0 &cppi41dma 20 0 + &cppi41dma 21 0 &cppi41dma 22 0 + &cppi41dma 23 0 &cppi41dma 24 0 + &cppi41dma 25 0 &cppi41dma 26 0 + &cppi41dma 27 0 &cppi41dma 28 0 + &cppi41dma 29 0 &cppi41dma 15 1 + &cppi41dma 16 1 &cppi41dma 17 1 + &cppi41dma 18 1 &cppi41dma 19 1 + &cppi41dma 20 1 &cppi41dma 21 1 + &cppi41dma 22 1 &cppi41dma 23 1 + &cppi41dma 24 1 &cppi41dma 25 1 + &cppi41dma 26 1 &cppi41dma 27 1 + &cppi41dma 28 1 &cppi41dma 29 1>; + dma-names = + "rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7", + "rx8", "rx9", "rx10", "rx11", "rx12", "rx13", + "rx14", "rx15", + "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7", + "tx8", "tx9", "tx10", "tx11", "tx12", "tx13", + "tx14", "tx15"; + }; + + cppi41dma: dma-controller@47402000 { + compatible = "ti,am3359-cppi41"; + reg = <0x47400000 0x1000 + 0x47402000 0x1000 + 0x47403000 0x1000 + 0x47404000 0x4000>; + reg-names = "glue", "controller", "scheduler", "queuemgr"; + interrupts = <17>; + interrupt-names = "glue"; + #dma-cells = <2>; + #dma-channels = <30>; + #dma-requests = <256>; + status = "disabled"; + }; + }; + + epwmss0: epwmss@48300000 { + compatible = "ti,am33xx-pwmss"; + reg = <0x48300000 0x10>; + ti,hwmods = "epwmss0"; + #address-cells = <1>; + #size-cells = <1>; + status = "disabled"; + ranges = <0x48300100 0x48300100 0x80 /* ECAP */ + 0x48300180 0x48300180 0x80 /* EQEP */ + 0x48300200 0x48300200 0x80>; /* EHRPWM */ + + ecap0: ecap@48300100 { + compatible = "ti,am33xx-ecap"; + #pwm-cells = <3>; + reg = <0x48300100 0x80>; + interrupts = <31>; + interrupt-names = "ecap0"; + ti,hwmods = "ecap0"; + status = "disabled"; + }; + + ehrpwm0: ehrpwm@48300200 { + compatible = "ti,am33xx-ehrpwm"; + #pwm-cells = <3>; + reg = <0x48300200 0x80>; + ti,hwmods = "ehrpwm0"; + status = "disabled"; + }; + }; + + epwmss1: epwmss@48302000 { + compatible = "ti,am33xx-pwmss"; + reg = <0x48302000 0x10>; + ti,hwmods = "epwmss1"; + #address-cells = <1>; + #size-cells = <1>; + status = "disabled"; + ranges = <0x48302100 0x48302100 0x80 /* ECAP */ + 0x48302180 0x48302180 0x80 /* EQEP */ + 0x48302200 0x48302200 0x80>; /* EHRPWM */ + + ecap1: ecap@48302100 { + compatible = "ti,am33xx-ecap"; + #pwm-cells = <3>; + reg = <0x48302100 0x80>; + interrupts = <47>; + interrupt-names = "ecap1"; + ti,hwmods = "ecap1"; + status = "disabled"; + }; + + ehrpwm1: ehrpwm@48302200 { + compatible = "ti,am33xx-ehrpwm"; + #pwm-cells = <3>; + reg = <0x48302200 0x80>; + ti,hwmods = "ehrpwm1"; + status = "disabled"; + }; + }; + + epwmss2: epwmss@48304000 { + compatible = "ti,am33xx-pwmss"; + reg = <0x48304000 0x10>; + ti,hwmods = "epwmss2"; + #address-cells = <1>; + #size-cells = <1>; + status = "disabled"; + ranges = <0x48304100 0x48304100 0x80 /* ECAP */ + 0x48304180 0x48304180 0x80 /* EQEP */ + 0x48304200 0x48304200 0x80>; /* EHRPWM */ + + ecap2: ecap@48304100 { + compatible = "ti,am33xx-ecap"; + #pwm-cells = <3>; + reg = <0x48304100 0x80>; + interrupts = <61>; + interrupt-names = "ecap2"; + ti,hwmods = "ecap2"; + status = "disabled"; + }; + + ehrpwm2: ehrpwm@48304200 { + compatible = "ti,am33xx-ehrpwm"; + #pwm-cells = <3>; + reg = <0x48304200 0x80>; + ti,hwmods = "ehrpwm2"; + status = "disabled"; + }; }; mac: ethernet@4a100000 { - compatible = "ti,cpsw"; + compatible = "ti,am335x-cpsw","ti,cpsw"; ti,hwmods = "cpgmac0"; + clocks = <&cpsw_125mhz_gclk>, <&cpsw_cpts_rft_clk>; + clock-names = "fck", "cpts"; cpdma_channels = <8>; ale_entries = <1024>; bd_ram_size = <0x2000>; @@ -369,6 +744,8 @@ */ interrupts = <40 41 42 43>; ranges; + syscon = <&scm_conf>; + status = "disabled"; davinci_mdio: mdio@4a101000 { compatible = "ti,davinci_mdio"; @@ -377,6 +754,7 @@ ti,hwmods = "davinci_mdio"; bus_freq = <1000000>; reg = <0x4a101000 0x100>; + status = "disabled"; }; cpsw_emac0: slave@4a100200 { @@ -388,25 +766,57 @@ /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; }; + + phy_sel: cpsw-phy-sel@44e10650 { + compatible = "ti,am3352-cpsw-phy-sel"; + reg= <0x44e10650 0x4>; + reg-names = "gmii-sel"; + }; }; ocmcram: ocmcram@40300000 { - compatible = "ti,am3352-ocmcram"; - reg = <0x40300000 0x10000>; - ti,hwmods = "ocmcram"; - ti,no_idle_on_suspend; + compatible = "mmio-sram"; + reg = <0x40300000 0x10000>; /* 64k */ + }; + + elm: elm@48080000 { + compatible = "ti,am3352-elm"; + reg = <0x48080000 0x2000>; + interrupts = <4>; + ti,hwmods = "elm"; + status = "disabled"; }; - wkup_m3: wkup_m3@44d00000 { - compatible = "ti,am3353-wkup-m3"; - reg = <0x44d00000 0x4000 /* M3 UMEM */ - 0x44d80000 0x2000>; /* M3 DMEM */ - ti,hwmods = "wkup_m3"; + lcdc: lcdc@4830e000 { + compatible = "ti,am33xx-tilcdc"; + reg = <0x4830e000 0x1000>; + interrupt-parent = <&intc>; + interrupts = <36>; + ti,hwmods = "lcdc"; + status = "disabled"; + }; + + tscadc: tscadc@44e0d000 { + compatible = "ti,am3359-tscadc"; + reg = <0x44e0d000 0x1000>; + interrupt-parent = <&intc>; + interrupts = <16>; + ti,hwmods = "adc_tsc"; + status = "disabled"; + + tsc { + compatible = "ti,am3359-tsc"; + }; + am335x_adc: adc { + #io-channel-cells = <1>; + compatible = "ti,am3359-adc"; + }; }; gpmc: gpmc@50000000 { compatible = "ti,am3352-gpmc"; ti,hwmods = "gpmc"; + ti,no-idle-on-init; reg = <0x50000000 0x2000>; interrupts = <100>; gpmc,num-cs = <7>; @@ -415,5 +825,61 @@ #size-cells = <1>; status = "disabled"; }; + + sham: sham@53100000 { + compatible = "ti,omap4-sham"; + ti,hwmods = "sham"; + reg = <0x53100000 0x200>; + interrupts = <109>; + dmas = <&edma 36>; + dma-names = "rx"; + }; + + aes: aes@53500000 { + compatible = "ti,omap4-aes"; + ti,hwmods = "aes"; + reg = <0x53500000 0xa0>; + interrupts = <103>; + dmas = <&edma 6>, + <&edma 5>; + dma-names = "tx", "rx"; + }; + + mcasp0: mcasp@48038000 { + compatible = "ti,am33xx-mcasp-audio"; + ti,hwmods = "mcasp0"; + reg = <0x48038000 0x2000>, + <0x46000000 0x400000>; + reg-names = "mpu", "dat"; + interrupts = <80>, <81>; + interrupt-names = "tx", "rx"; + status = "disabled"; + dmas = <&edma 8>, + <&edma 9>; + dma-names = "tx", "rx"; + }; + + mcasp1: mcasp@4803C000 { + compatible = "ti,am33xx-mcasp-audio"; + ti,hwmods = "mcasp1"; + reg = <0x4803C000 0x2000>, + <0x46400000 0x400000>; + reg-names = "mpu", "dat"; + interrupts = <82>, <83>; + interrupt-names = "tx", "rx"; + status = "disabled"; + dmas = <&edma 10>, + <&edma 11>; + dma-names = "tx", "rx"; + }; + + rng: rng@48310000 { + compatible = "ti,omap4-rng"; + ti,hwmods = "rng"; + reg = <0x48310000 0x2000>; + interrupts = <111>; + }; }; }; + +/include/ "am33xx-clocks.dtsi"