--- zzzz-none-000/linux-3.10.107/arch/arm/boot/dts/at91sam9263ek.dts	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/arch/arm/boot/dts/at91sam9263ek.dts	2021-02-04 17:41:59.000000000 +0000
@@ -6,14 +6,15 @@
  * Licensed under GPLv2 only
  */
 /dts-v1/;
-/include/ "at91sam9263.dtsi"
+#include "at91sam9263.dtsi"
 
 / {
 	model = "Atmel at91sam9263ek";
 	compatible = "atmel,at91sam9263ek", "atmel,at91sam9263", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs";
+		bootargs = "mem=64M root=/dev/mtdblock5 rw rootfstype=ubifs";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
@@ -21,12 +22,11 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
 
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
+		main_xtal {
 			clock-frequency = <16367660>;
 		};
 	};
@@ -51,7 +51,7 @@
 			};
 
 			usb1: gadget@fff78000 {
-				atmel,vbus-gpio = <&pioA 25 0>;
+				atmel,vbus-gpio = <&pioA 25 GPIO_ACTIVE_HIGH>;
 				status = "okay";
 			};
 
@@ -65,8 +65,8 @@
 				slot@0 {
 					reg = <0>;
 					bus-width = <4>;
-					cd-gpios = <&pioE 18 0>;
-					wp-gpios = <&pioE 19 0>;
+					cd-gpios = <&pioE 18 GPIO_ACTIVE_HIGH>;
+					wp-gpios = <&pioE 19 GPIO_ACTIVE_HIGH>;
 				};
 			};
 
@@ -74,8 +74,8 @@
 				mmc0 {
 					pinctrl_board_mmc0: mmc0-board {
 						atmel,pins =
-							<5 18 0x0 0x5	/* PE18 gpio CD pin pull up and deglitch */
-							 5 19 0x0 0x1>;	/* PE19 gpio WP pin pull up */
+							<AT91_PIOE 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH 	/* PE18 gpio CD pin pull up and deglitch */
+							 AT91_PIOE 19 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;	/* PE19 gpio WP pin pull up */
 					};
 				};
 			};
@@ -89,6 +89,40 @@
 					reg = <0>;
 				};
 			};
+
+			watchdog@fffffd40 {
+				status = "okay";
+			};
+		};
+
+		fb0: fb@0x00700000 {
+			display = <&display0>;
+			status = "okay";
+
+			display0: display {
+				bits-per-pixel = <16>;
+				atmel,lcdcon-backlight;
+				atmel,dmacon = <0x1>;
+				atmel,lcdcon2 = <0x80008002>;
+				atmel,guard-time = <1>;
+
+				display-timings {
+					native-mode = <&timing0>;
+					timing0: timing0 {
+						clock-frequency = <4965000>;
+						hactive = <240>;
+						vactive = <320>;
+						hback-porch = <1>;
+						hfront-porch = <33>;
+						vback-porch = <1>;
+						vfront-porch = <0>;
+						hsync-len = <5>;
+						vsync-len = <1>;
+						hsync-active = <1>;
+						vsync-active = <1>;
+					};
+				};
+			};
 		};
 
 		nand0: nand@40000000 {
@@ -141,8 +175,8 @@
 		usb0: ohci@00a00000 {
 			num-ports = <2>;
 			status = "okay";
-			atmel,vbus-gpio = <&pioA 24 0
-					   &pioA 21 0
+			atmel,vbus-gpio = <&pioA 24 GPIO_ACTIVE_HIGH
+					   &pioA 21 GPIO_ACTIVE_HIGH
 					  >;
 		};
 	};
@@ -152,13 +186,13 @@
 
 		d3 {
 			label = "d3";
-			gpios = <&pioB 7 0>;
+			gpios = <&pioB 7 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
 		d2 {
 			label = "d2";
-			gpios = <&pioC 29 1>;
+			gpios = <&pioC 29 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "nand-disk";
 		};
 	};
@@ -168,16 +202,16 @@
 
 		left_click {
 			label = "left_click";
-			gpios = <&pioC 5 1>;
+			gpios = <&pioC 5 GPIO_ACTIVE_LOW>;
 			linux,code = <272>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		right_click {
 			label = "right_click";
-			gpios = <&pioC 4 1>;
+			gpios = <&pioC 4 GPIO_ACTIVE_LOW>;
 			linux,code = <273>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};