--- zzzz-none-000/linux-3.10.107/arch/arm/boot/dts/at91sam9m10g45ek.dts 2017-06-27 09:49:32.000000000 +0000 +++ scorpion-7490-727/linux-3.10.107/arch/arm/boot/dts/at91sam9m10g45ek.dts 2021-02-04 17:41:59.000000000 +0000 @@ -7,14 +7,16 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "at91sam9g45.dtsi" +#include "at91sam9g45.dtsi" +#include / { model = "Atmel AT91SAM9M10G45-EK"; compatible = "atmel,at91sam9m10g45ek", "atmel,at91sam9g45", "atmel,at91sam9"; chosen { - bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=jffs2"; + bootargs = "mem=64M root=/dev/mtdblock1 rw rootfstype=jffs2"; + stdout-path = "serial0:115200n8"; }; memory { @@ -22,13 +24,12 @@ }; clocks { - #address-cells = <1>; - #size-cells = <1>; - ranges; - - main_clock: clock@0 { - compatible = "atmel,osc", "fixed-clock"; - clock-frequency = <12000000>; + slow_xtal { + clock-frequency = <32768>; + }; + + main_xtal { + clock-frequency = <12000000>; }; }; @@ -53,12 +54,35 @@ i2c0: i2c@fff84000 { status = "okay"; + ov2640: camera@30 { + compatible = "ovti,ov2640"; + reg = <0x30>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>; + resetb-gpios = <&pioD 12 GPIO_ACTIVE_LOW>; + pwdn-gpios = <&pioD 13 GPIO_ACTIVE_HIGH>; + clocks = <&pck1>; + clock-names = "xvclk"; + assigned-clocks = <&pck1>; + assigned-clock-rates = <25000000>; + + port { + ov2640_0: endpoint { + remote-endpoint = <&isi_0>; + bus-width = <8>; + }; + }; + }; }; i2c1: i2c@fff88000 { status = "okay"; }; + watchdog@fffffd40 { + status = "okay"; + }; + mmc0: mmc@fff80000 { pinctrl-0 = < &pinctrl_board_mmc0 @@ -68,7 +92,7 @@ slot@0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 10 0>; + cd-gpios = <&pioD 10 GPIO_ACTIVE_HIGH>; }; }; @@ -81,24 +105,48 @@ slot@0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 11 0>; - wp-gpios = <&pioD 29 0>; + cd-gpios = <&pioD 11 GPIO_ACTIVE_HIGH>; + wp-gpios = <&pioD 29 GPIO_ACTIVE_HIGH>; }; }; pinctrl@fffff200 { + camera_sensor { + pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 { + atmel,pins = + ; + }; + + pinctrl_sensor_reset: sensor_reset-0 { + atmel,pins = + ; + }; + + pinctrl_sensor_power: sensor_power-0 { + atmel,pins = + ; + }; + }; mmc0 { pinctrl_board_mmc0: mmc0-board { atmel,pins = - <3 10 0x0 0x5>; /* PD10 gpio CD pin pull up and deglitch */ + ; /* PD10 gpio CD pin pull up and deglitch */ }; }; mmc1 { pinctrl_board_mmc1: mmc1-board { atmel,pins = - <3 11 0x0 0x5 /* PD11 gpio CD pin pull up and deglitch */ - 3 29 0x0 0x1>; /* PD29 gpio WP pin pull up */ + ; /* PD29 gpio WP pin pull up */ + }; + }; + + pwm0 { + pinctrl_pwm_leds: pwm-led { + atmel,pins = + ; /* PD31 periph B */ }; }; }; @@ -112,6 +160,89 @@ reg = <0>; }; }; + + usb2: gadget@fff78000 { + atmel,vbus-gpio = <&pioB 19 GPIO_ACTIVE_HIGH>; + status = "okay"; + }; + + adc0: adc@fffb0000 { + pinctrl-names = "default"; + pinctrl-0 = < + &pinctrl_adc0_ad0 + &pinctrl_adc0_ad1 + &pinctrl_adc0_ad2 + &pinctrl_adc0_ad3 + &pinctrl_adc0_ad4 + &pinctrl_adc0_ad5 + &pinctrl_adc0_ad6 + &pinctrl_adc0_ad7>; + atmel,adc-ts-wires = <4>; + status = "okay"; + }; + + isi@fffb4000 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_isi_data_0_7>; + status = "okay"; + port { + isi_0: endpoint { + remote-endpoint = <&ov2640_0>; + bus-width = <8>; + vsync-active = <1>; + hsync-active = <1>; + }; + }; + }; + + pwm0: pwm@fffb8000 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm_leds>; + }; + + rtc@fffffd20 { + atmel,rtt-rtc-time-reg = <&gpbr 0x0>; + status = "okay"; + }; + + gpbr: syscon@fffffd60 { + status = "okay"; + }; + + rtc@fffffdb0 { + status = "okay"; + }; + }; + + fb0: fb@0x00500000 { + display = <&display0>; + status = "okay"; + + display0: display { + bits-per-pixel = <32>; + atmel,lcdcon-backlight; + atmel,dmacon = <0x1>; + atmel,lcdcon2 = <0x80008002>; + atmel,guard-time = <9>; + atmel,lcd-wiring-mode = "RGB"; + + display-timings { + native-mode = <&timing0>; + timing0: timing0 { + clock-frequency = <9000000>; + hactive = <480>; + vactive = <272>; + hback-porch = <1>; + hfront-porch = <1>; + vback-porch = <40>; + vfront-porch = <1>; + hsync-len = <45>; + vsync-len = <1>; + }; + }; + }; }; nand0: nand@40000000 { @@ -139,8 +270,8 @@ usb0: ohci@00700000 { status = "okay"; num-ports = <2>; - atmel,vbus-gpio = <&pioD 1 1 - &pioD 3 1>; + atmel,vbus-gpio = <&pioD 1 GPIO_ACTIVE_LOW + &pioD 3 GPIO_ACTIVE_LOW>; }; usb1: ehci@00800000 { @@ -153,19 +284,25 @@ d8 { label = "d8"; - gpios = <&pioD 30 0>; + gpios = <&pioD 30 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; + }; + + pwmleds { + compatible = "pwm-leds"; d6 { label = "d6"; - gpios = <&pioD 0 1>; + pwms = <&pwm0 3 5000 PWM_POLARITY_INVERTED>; + max-brightness = <255>; linux,default-trigger = "nand-disk"; }; d7 { label = "d7"; - gpios = <&pioD 31 1>; + pwms = <&pwm0 1 5000 PWM_POLARITY_INVERTED>; + max-brightness = <255>; linux,default-trigger = "mmc0"; }; }; @@ -175,45 +312,45 @@ left_click { label = "left_click"; - gpios = <&pioB 6 1>; + gpios = <&pioB 6 GPIO_ACTIVE_LOW>; linux,code = <272>; - gpio-key,wakeup; + wakeup-source; }; right_click { label = "right_click"; - gpios = <&pioB 7 1>; + gpios = <&pioB 7 GPIO_ACTIVE_LOW>; linux,code = <273>; - gpio-key,wakeup; + wakeup-source; }; left { label = "Joystick Left"; - gpios = <&pioB 14 1>; + gpios = <&pioB 14 GPIO_ACTIVE_LOW>; linux,code = <105>; }; right { label = "Joystick Right"; - gpios = <&pioB 15 1>; + gpios = <&pioB 15 GPIO_ACTIVE_LOW>; linux,code = <106>; }; up { label = "Joystick Up"; - gpios = <&pioB 16 1>; + gpios = <&pioB 16 GPIO_ACTIVE_LOW>; linux,code = <103>; }; down { label = "Joystick Down"; - gpios = <&pioB 17 1>; + gpios = <&pioB 17 GPIO_ACTIVE_LOW>; linux,code = <108>; }; enter { label = "Joystick Press"; - gpios = <&pioB 18 1>; + gpios = <&pioB 18 GPIO_ACTIVE_LOW>; linux,code = <28>; }; };