--- zzzz-none-000/linux-3.10.107/arch/arm/boot/dts/at91sam9x5ek.dtsi	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/arch/arm/boot/dts/at91sam9x5ek.dtsi	2021-02-04 17:41:59.000000000 +0000
@@ -6,14 +6,15 @@
  *
  * Licensed under GPLv2 or later.
  */
-/include/ "at91sam9x5cm.dtsi"
+#include "at91sam9x5cm.dtsi"
 
 / {
 	model = "Atmel AT91SAM9X5-EK";
 	compatible = "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs";
+		bootargs = "root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs";
+		stdout-path = "serial0:115200n8";
 	};
 
 	ahb {
@@ -27,7 +28,7 @@
 				slot@0 {
 					reg = <0>;
 					bus-width = <4>;
-					cd-gpios = <&pioD 15 0>;
+					cd-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>;
 				};
 			};
 
@@ -40,7 +41,7 @@
 				slot@0 {
 					reg = <0>;
 					bus-width = <4>;
-					cd-gpios = <&pioD 14 0>;
+					cd-gpios = <&pioD 14 GPIO_ACTIVE_HIGH>;
 				};
 			};
 
@@ -52,22 +53,97 @@
 				status = "okay";
 			};
 
+			usb2: gadget@f803c000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_board_usb2>;
+				atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>;
+				status = "okay";
+			};
+
+			isi: isi@f8048000 {
+				status = "disabled";
+				port {
+					isi_0: endpoint@0 {
+						remote-endpoint = <&ov2640_0>;
+						bus-width = <8>;
+						vsync-active = <1>;
+						hsync-active = <1>;
+					};
+				};
+			};
+
 			i2c0: i2c@f8010000 {
 				status = "okay";
+
+				wm8731: wm8731@1a {
+					compatible = "wm8731";
+					reg = <0x1a>;
+				};
+
+				ov2640: camera@0x30 {
+					compatible = "ovti,ov2640";
+					reg = <0x30>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
+					resetb-gpios = <&pioA 7 GPIO_ACTIVE_LOW>;
+					pwdn-gpios = <&pioA 13 GPIO_ACTIVE_HIGH>;
+					clocks = <&pck0>;
+					clock-names = "xvclk";
+					assigned-clocks = <&pck0>;
+					assigned-clock-rates = <25000000>;
+					status = "disabled";
+
+					port {
+						ov2640_0: endpoint {
+							remote-endpoint = <&isi_0>;
+							bus-width = <8>;
+						};
+					};
+				};
+			};
+
+			adc0: adc@f804c000 {
+				atmel,adc-ts-wires = <4>;
+				atmel,adc-ts-pressure-threshold = <10000>;
+				status = "okay";
 			};
 
 			pinctrl@fffff400 {
+				camera_sensor {
+					pinctrl_pck0_as_isi_mck: pck0_as_isi_mck-0 {
+						atmel,pins =
+							<AT91_PIOC 15 AT91_PERIPH_C AT91_PINCTRL_NONE>;	/* ISI_MCK */
+					};
+
+					pinctrl_sensor_power: sensor_power-0 {
+						atmel,pins =
+							<AT91_PIOA 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_sensor_reset: sensor_reset-0 {
+						atmel,pins =
+							<AT91_PIOA 7 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+					};
+				};
+
 				mmc0 {
 					pinctrl_board_mmc0: mmc0-board {
 						atmel,pins =
-							<3 15 0x0 0x5>;	/* PD15 gpio CD pin pull up and deglitch */
+							<AT91_PIOD 15 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;	/* PD15 gpio CD pin pull up and deglitch */
 					};
 				};
 
 				mmc1 {
 					pinctrl_board_mmc1: mmc1-board {
 						atmel,pins =
-							<3 14 0x0 0x5>;	/* PD14 gpio CD pin pull up and deglitch */
+							<AT91_PIOD 14 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;	/* PD14 gpio CD pin pull up and deglitch */
+					};
+				};
+
+				usb2 {
+					pinctrl_board_usb2: usb2-board {
+						atmel,pins =
+							<AT91_PIOB 16 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;		/* PB16 gpio vbus sense, deglitch */
 					};
 				};
 			};
@@ -81,13 +157,22 @@
 					reg = <0>;
 				};
 			};
+
+			watchdog@fffffe40 {
+				status = "okay";
+			};
+
+			ssc0: ssc@f0010000 {
+				status = "okay";
+			};
 		};
 
 		usb0: ohci@00600000 {
 			status = "okay";
-			num-ports = <2>;
-			atmel,vbus-gpio = <&pioD 19 1
-					   &pioD 20 1
+			num-ports = <3>;
+			atmel,vbus-gpio = <0 /* &pioD 18 GPIO_ACTIVE_LOW *//* Activate to have access to port A */
+					   &pioD 19 GPIO_ACTIVE_LOW
+					   &pioD 20 GPIO_ACTIVE_LOW
 					  >;
 		};
 
@@ -95,4 +180,19 @@
 			status = "okay";
 		};
 	};
+
+	sound {
+		compatible = "atmel,sam9x5-wm8731-audio";
+
+		atmel,model = "wm8731 @ AT91SAM9X5EK";
+
+		atmel,audio-routing =
+			"Headphone Jack", "RHPOUT",
+			"Headphone Jack", "LHPOUT",
+			"LLINEIN", "Line In Jack",
+			"RLINEIN", "Line In Jack";
+
+		atmel,ssc-controller = <&ssc0>;
+		atmel,audio-codec = <&wm8731>;
+	};
 };