--- zzzz-none-000/linux-3.10.107/arch/arm/boot/dts/imx28-cfa10036.dts	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/arch/arm/boot/dts/imx28-cfa10036.dts	2021-02-04 17:41:59.000000000 +0000
@@ -10,7 +10,7 @@
  */
 
 /dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
 
 / {
 	model = "Crystalfontz CFA-10036 Board";
@@ -23,28 +23,47 @@
 	apb@80000000 {
 		apbh@80000000 {
 			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_cfa10036>;
-
-				hog_pins_cfa10036: hog-10036@0 {
+				ssd1306_cfa10036: ssd1306-10036@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
-						0x2073 /* MX28_PAD_SSP0_D7__GPIO_2_7 */
+						MX28_PAD_SSP0_DATA7__GPIO_2_7
 					>;
-					fsl,drive-strength = <0>;
-					fsl,voltage = <1>;
-					fsl,pull-up = <0>;
+					fsl,drive-strength = <MXS_DRIVE_4mA>;
+					fsl,voltage = <MXS_VOLTAGE_HIGH>;
+					fsl,pull-up = <MXS_PULL_DISABLE>;
 				};
 
 				led_pins_cfa10036: leds-10036@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
-						0x3043 /* MX28_PAD_AUART1_RX__GPIO_3_4 */
+						MX28_PAD_AUART1_RX__GPIO_3_4
+					>;
+					fsl,drive-strength = <MXS_DRIVE_4mA>;
+					fsl,voltage = <MXS_VOLTAGE_HIGH>;
+					fsl,pull-up = <MXS_PULL_DISABLE>;
+				};
+
+				usb0_otg_cfa10036: otg-10036@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						MX28_PAD_GPMI_RDY0__USB0_ID
+					>;
+					fsl,drive-strength = <MXS_DRIVE_4mA>;
+					fsl,voltage = <MXS_VOLTAGE_HIGH>;
+					fsl,pull-up = <MXS_PULL_DISABLE>;
+				};
+
+				mmc_pwr_cfa10036: mmc_pwr_cfa10036@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x31c3 /*
+						MX28_PAD_PWM3__GPIO_3_28 */
 					>;
 					fsl,drive-strength = <0>;
 					fsl,voltage = <1>;
 					fsl,pull-up = <0>;
 				};
+
 			};
 
 			ssp0: ssp@80010000 {
@@ -52,18 +71,13 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&mmc0_4bit_pins_a
 					&mmc0_cd_cfg &mmc0_sck_cfg>;
+				vmmc-supply = <&reg_vddio_sd0>;
 				bus-width = <4>;
 				status = "okay";
 			};
 		};
 
 		apbx@80040000 {
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm4_pins_a>;
-				status = "okay";
-			};
-
 			duart: serial@80074000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&duart_pins_b>;
@@ -73,15 +87,37 @@
 			i2c0: i2c@80058000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&i2c0_pins_b>;
+				clock-frequency = <400000>;
 				status = "okay";
 
-				ssd1307: oled@3c {
-					compatible = "solomon,ssd1307fb-i2c";
+				ssd1306: oled@3c {
+					compatible = "solomon,ssd1306fb-i2c";
+					pinctrl-names = "default";
+					pinctrl-0 = <&ssd1306_cfa10036>;
 					reg = <0x3c>;
-					pwms = <&pwm 4 3000>;
 					reset-gpios = <&gpio2 7 0>;
+					solomon,height = <32>;
+					solomon,width = <128>;
+					solomon,page-offset = <0>;
+					solomon,com-lrremap;
+					solomon,com-invdir;
+					solomon,com-offset = <32>;
 				};
 			};
+
+			usbphy0: usbphy@8007c000 {
+				status = "okay";
+			};
+		};
+	};
+
+	ahb@80080000 {
+		usb0: usb@80080000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&usb0_otg_cfa10036>;
+			dr_mode = "peripheral";
+			phy_type = "utmi";
+			status = "okay";
 		};
 	};
 
@@ -95,4 +131,14 @@
 			default-state = "on";
 		};
 	};
+
+	reg_vddio_sd0: vddio-sd0 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&mmc_pwr_cfa10036>;
+		regulator-name = "vddio-sd0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 28 0>;
+	};
 };