--- zzzz-none-000/linux-3.10.107/arch/arm/boot/dts/integratorcp.dts	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/arch/arm/boot/dts/integratorcp.dts	2021-02-04 17:41:59.000000000 +0000
@@ -13,25 +13,107 @@
 		bootargs = "root=/dev/ram0 console=ttyAMA0,38400n8 earlyprintk";
 	};
 
-	cpcon {
-		/* CP controller registers */
+	/*
+	 * The Integrator/CP overall clocking architecture can be found in
+	 * ARM DUI 0184B page 7-28 "Integrator/CP922T system clocks" which
+	 * appear to illustrate the layout used in most configurations.
+	 */
+
+	/* The codec chrystal operates at 24.576 MHz */
+	xtal_codec: xtal24.576@24.576M {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <24576000>;
+	};
+
+	/* The chrystal is divided by 2 by the codec for the AACI bit clock */
+	aaci_bitclk: aaci_bitclk@12.288M {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clock-div = <2>;
+		clock-mult = <1>;
+		clocks = <&xtal_codec>;
+	};
+
+	/* This is a 25MHz chrystal on the base board */
+	xtal25mhz: xtal25mhz@25M {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <25000000>;
+	};
+
+	/* The UART clock is 14.74 MHz divided from 25MHz by an ICS525 */
+	uartclk: uartclk@14.74M {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <14745600>;
+	};
+
+	/* Actually sysclk I think */
+	pclk: pclk@0 {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <0>;
+	};
+
+	core-module@10000000 {
+		/* 24 MHz chrystal on the core module */
+		xtal24mhz: xtal24mhz@24M {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+		};
+
+		/*
+		 * External oscillator on the core module, usually used
+		 * to drive video circuitry. Driven from the 24MHz clock.
+		 */
+		auxosc: cm_aux_osc@25M {
+			#clock-cells = <0>;
+			compatible = "arm,integrator-cm-auxosc";
+			clocks = <&xtal24mhz>;
+		};
+
+		/* The KMI clock is the 24 MHz oscillator divided to 8MHz */
+		kmiclk: kmiclk@1M {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clock-div = <3>;
+			clock-mult = <1>;
+			clocks = <&xtal24mhz>;
+		};
+
+		/* The timer clock is the 24 MHz oscillator divided to 1MHz */
+		timclk: timclk@1M {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clock-div = <24>;
+			clock-mult = <1>;
+			clocks = <&xtal24mhz>;
+		};
+	};
+
+	syscon {
+		compatible = "arm,integrator-cp-syscon";
 		reg = <0xcb000000 0x100>;
 	};
 
 	timer0: timer@13000000 {
-		/* TIMER0 runs @ 25MHz */
+		/* TIMER0 runs directly on the 25MHz chrystal */
 		compatible = "arm,integrator-cp-timer";
-		status = "disabled";
+		clocks = <&xtal25mhz>;
 	};
 
 	timer1: timer@13000100 {
 		/* TIMER1 runs @ 1MHz */
 		compatible = "arm,integrator-cp-timer";
+		clocks = <&timclk>;
 	};
 
 	timer2: timer@13000200 {
 		/* TIMER2 runs @ 1MHz */
 		compatible = "arm,integrator-cp-timer";
+		clocks = <&timclk>;
 	};
 
 	pic: pic@14000000 {
@@ -47,8 +129,11 @@
 		valid-mask = <0x00000007>;
 	};
 
+	/* The SIC is cascaded off IRQ 26 on the PIC */
 	sic: sic@ca000000 {
 		compatible = "arm,versatile-fpga-irq";
+		interrupt-parent = <&pic>;
+		interrupts = <26>;
 		#interrupt-cells = <1>;
 		interrupt-controller;
 		reg = <0xca000000 0x100>;
@@ -71,22 +156,32 @@
 		 */
 		rtc@15000000 {
 			compatible = "arm,pl031", "arm,primecell";
+			clocks = <&pclk>;
+			clock-names = "apb_pclk";
 		};
 
 		uart@16000000 {
 			compatible = "arm,pl011", "arm,primecell";
+			clocks = <&uartclk>, <&pclk>;
+			clock-names = "uartclk", "apb_pclk";
 		};
 
 		uart@17000000 {
 			compatible = "arm,pl011", "arm,primecell";
+			clocks = <&uartclk>, <&pclk>;
+			clock-names = "uartclk", "apb_pclk";
 		};
 
 		kmi@18000000 {
 			compatible = "arm,pl050", "arm,primecell";
+			clocks = <&kmiclk>, <&pclk>;
+			clock-names = "KMIREFCLK", "apb_pclk";
 		};
 
 		kmi@19000000 {
 			compatible = "arm,pl050", "arm,primecell";
+			clocks = <&kmiclk>, <&pclk>;
+			clock-names = "KMIREFCLK", "apb_pclk";
 		};
 
 		/*
@@ -97,18 +192,24 @@
 			reg = <0x1c000000 0x1000>;
 			interrupts = <23 24>;
 			max-frequency = <515633>;
+			clocks = <&uartclk>, <&pclk>;
+			clock-names = "mclk", "apb_pclk";
 		};
 
 		aaci@1d000000 {
 			compatible = "arm,pl041", "arm,primecell";
 			reg = <0x1d000000 0x1000>;
 			interrupts = <25>;
+			clocks = <&pclk>;
+			clock-names = "apb_pclk";
 		};
 
 		clcd@c0000000 {
 			compatible = "arm,pl110", "arm,primecell";
 			reg = <0xC0000000 0x1000>;
 			interrupts = <22>;
+			clocks = <&auxosc>, <&pclk>;
+			clock-names = "clcd", "apb_pclk";
 		};
 	};
 };