--- zzzz-none-000/linux-3.10.107/arch/arm/boot/dts/kirkwood-98dx4122.dtsi	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/arch/arm/boot/dts/kirkwood-98dx4122.dtsi	2021-02-04 17:41:59.000000000 +0000
@@ -1,31 +1,51 @@
 / {
+	mbus {
+		pciec: pcie-controller {
+			compatible = "marvell,kirkwood-pcie";
+			status = "disabled";
+			device_type = "pci";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			bus-range = <0x00 0xff>;
+
+			ranges =
+			       <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+				0x82000000 0x1 0     MBUS_ID(0x04, 0xe8) 0       1 0 /* Port 0.0 MEM */
+				0x81000000 0x1 0     MBUS_ID(0x04, 0xe0) 0       1 0 /* Port 0.0 IO  */>;
+
+			pcie0: pcie@1,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x00040000 0 0x2000>;
+				reg = <0x0800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &intc 9>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gate_clk 2>;
+				status = "disabled";
+			};
+		};
+	};
+
 	ocp@f1000000 {
-		pinctrl: pinctrl@10000 {
+		pinctrl: pin-controller@10000 {
 			compatible = "marvell,98dx4122-pinctrl";
-			reg = <0x10000 0x20>;
 
-			pmx_nand: pmx-nand {
-				marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3",
-					       "mpp4", "mpp5", "mpp18",
-					       "mpp19";
-				marvell,function = "nand";
-			};
-			pmx_spi: pmx-spi {
-				marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3";
-				marvell,function = "spi";
-			};
-			pmx_twsi0: pmx-twsi0 {
-				marvell,pins = "mpp8", "mpp9";
-				marvell,function = "twsi0";
-			};
-			pmx_uart0: pmx-uart0 {
-				marvell,pins = "mpp10", "mpp11";
-				marvell,function = "uart0";
-			};
-			pmx_uart1: pmx-uart1 {
-				marvell,pins = "mpp13", "mpp14";
-				marvell,function = "uart1";
-			};
 		};
 	};
 };
+
+&sata_phy0 {
+	status = "disabled";
+};
+
+&sata_phy1 {
+	status = "disabled";
+};