--- zzzz-none-000/linux-3.10.107/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts	2021-02-04 17:41:59.000000000 +0000
@@ -1,7 +1,7 @@
 /dts-v1/;
 
-/include/ "kirkwood.dtsi"
-/include/ "kirkwood-6281.dtsi"
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
 
 / {
 	model = "Iomega StorCenter ix2-200";
@@ -14,16 +14,12 @@
 
 	chosen {
 		bootargs = "console=ttyS0,115200n8 earlyprintk";
+		stdout-path = &uart0;
 	};
 
 	ocp@f1000000 {
-		pinctrl: pinctrl@10000 {
-
-			pinctrl-0 = < &pmx_button_reset &pmx_button_power
-				      &pmx_led_backup &pmx_led_power
-				      &pmx_button_otb &pmx_led_rebuild
-				      &pmx_led_health
-				      &pmx_led_sata_brt_ctrl_1
+		pinctrl: pin-controller@10000 {
+			pinctrl-0 = < &pmx_led_sata_brt_ctrl_1
 				      &pmx_led_sata_brt_ctrl_2
 				      &pmx_led_backup_brt_ctrl_1
 				      &pmx_led_backup_brt_ctrl_2
@@ -118,31 +114,6 @@
 			status = "ok";
 		};
 
-		nand@3000000 {
-			status = "okay";
-
-			partition@0 {
-				label = "u-boot";
-				reg = <0x0000000 0x100000>;
-				read-only;
-			};
-
-			partition@a0000 {
-				label = "env";
-				reg = <0xa0000 0x20000>;
-				read-only;
-			};
-
-			partition@100000 {
-				label = "uImage";
-				reg = <0x100000 0x300000>;
-			};
-
-			partition@400000 {
-				label = "uInitrd";
-				reg = <0x540000 0x1000000>;
-			};
-		};
 		sata@80000 {
 			status = "okay";
 			nr-ports = <2>;
@@ -151,43 +122,104 @@
 	};
 	gpio-leds {
 		compatible = "gpio-leds";
+		pinctrl-0 = < &pmx_led_backup &pmx_led_power
+			      &pmx_led_rebuild &pmx_led_health >;
+		pinctrl-names = "default";
 
 		power_led {
 			label = "status:white:power_led";
-			gpios = <&gpio0 16 0>;
-			linux,default-trigger = "default-on";
+			gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
 		};
 		rebuild_led {
 			label = "status:white:rebuild_led";
-			gpios = <&gpio1 4 0>;
+			gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
 		};
 		health_led {
 			label = "status:red:health_led";
-			gpios = <&gpio1 5 0>;
+			gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
 		};
 		backup_led {
 			label = "status:blue:backup_led";
-			gpios = <&gpio0 15 0>;
+			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
 		};
 	};
 	gpio-keys {
 		compatible = "gpio-keys";
 		#address-cells = <1>;
 		#size-cells = <0>;
+		pinctrl-0 = <&pmx_button_reset &pmx_button_power
+			     &pmx_button_otb>;
+		pinctrl-names = "default";
+
+
 		Power {
 			label = "Power Button";
-			linux,code = <116>;
-			gpios = <&gpio0 14 1>;
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
 		};
 		Reset {
 			label = "Reset Button";
-			linux,code = <0x198>;
-			gpios = <&gpio0 12 1>;
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
 		};
 		OTB {
 			label = "OTB Button";
-			linux,code = <133>;
-			gpios = <&gpio1 3 1>;
+			linux,code = <KEY_COPY>;
+			gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
 		};
 	};
+	gpio-poweroff {
+		compatible = "gpio-poweroff";
+		gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&nand {
+	status = "okay";
+
+	partition@0 {
+		label = "u-boot";
+		reg = <0x0000000 0x100000>;
+		read-only;
+	};
+
+	partition@a0000 {
+		label = "env";
+		reg = <0xa0000 0x20000>;
+		read-only;
+	};
+
+	partition@100000 {
+		label = "uImage";
+		reg = <0x100000 0x300000>;
+	};
+
+	partition@400000 {
+		label = "rootfs";
+		reg = <0x400000 0x1C00000>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy1: ethernet-phy@11 {
+		reg = <11>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		speed = <1000>;
+		duplex = <1>;
+	};
+};
+
+&eth1 {
+	status = "okay";
+	ethernet1-port@0 {
+		phy-handle = <&ethphy1>;
+	};
 };