--- zzzz-none-000/linux-3.10.107/arch/arm/boot/dts/omap4.dtsi	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/arch/arm/boot/dts/omap4.dtsi	2021-02-04 17:41:59.000000000 +0000
@@ -6,21 +6,21 @@
  * published by the Free Software Foundation.
  */
 
-/*
- * Carveout for multimedia usecases
- * It should be the last 48MB of the first 512MB memory part
- * In theory, it should not even exist. That zone should be reserved
- * dynamically during the .reserve callback.
- */
-/memreserve/ 0x9d000000 0x03000000;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/omap.h>
 
-/include/ "skeleton.dtsi"
+#include "skeleton.dtsi"
 
 / {
 	compatible = "ti,omap4430", "ti,omap4";
-	interrupt-parent = <&gic>;
+	interrupt-parent = <&wakeupgen>;
 
 	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c2;
+		i2c2 = &i2c3;
+		i2c3 = &i2c4;
 		serial0 = &uart1;
 		serial1 = &uart2;
 		serial2 = &uart3;
@@ -28,13 +28,25 @@
 	};
 
 	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
 		cpu@0 {
 			compatible = "arm,cortex-a9";
+			device_type = "cpu";
 			next-level-cache = <&L2>;
+			reg = <0x0>;
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
 		};
 		cpu@1 {
 			compatible = "arm,cortex-a9";
+			device_type = "cpu";
 			next-level-cache = <&L2>;
+			reg = <0x1>;
 		};
 	};
 
@@ -44,6 +56,7 @@
 		#interrupt-cells = <3>;
 		reg = <0x48241000 0x1000>,
 		      <0x48240100 0x0100>;
+		interrupt-parent = <&gic>;
 	};
 
 	L2: l2-cache-controller@48242000 {
@@ -53,14 +66,24 @@
 		cache-level = <2>;
 	};
 
-	local-timer@0x48240600 {
+	local-timer@48240600 {
 		compatible = "arm,cortex-a9-twd-timer";
+		clocks = <&mpu_periphclk>;
 		reg = <0x48240600 0x20>;
-		interrupts = <1 13 0x304>;
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>;
+		interrupt-parent = <&gic>;
+	};
+
+	wakeupgen: interrupt-controller@48281000 {
+		compatible = "ti,omap4-wugen-mpu";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		reg = <0x48281000 0x1000>;
+		interrupt-parent = <&gic>;
 	};
 
 	/*
-	 * The soc node represents the soc top level view. It is uses for IPs
+	 * The soc node represents the soc top level view. It is used for IPs
 	 * that are not memory mapped in the MPU view or for the MPU itself.
 	 */
 	soc {
@@ -68,6 +91,7 @@
 		mpu {
 			compatible = "ti,omap4-mpu";
 			ti,hwmods = "mpu";
+			sram = <&ocmcram>;
 		};
 
 		dsp {
@@ -84,7 +108,7 @@
 	/*
 	 * XXX: Use a flat representation of the OMAP4 interconnect.
 	 * The real OMAP interconnect network is quite complex.
-	 * Since that will not bring real advantage to represent that in DT for
+	 * Since it will not bring real advantage to represent that in DT for
 	 * the moment, just use a fake OCP bus entry to represent the whole bus
 	 * hierarchy.
 	 */
@@ -97,48 +121,170 @@
 		reg = <0x44000000 0x1000>,
 		      <0x44800000 0x2000>,
 		      <0x45000000 0x1000>;
-		interrupts = <0 9 0x4>,
-			     <0 10 0x4>;
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
 
-		counter32k: counter@4a304000 {
-			compatible = "ti,omap-counter32k";
-			reg = <0x4a304000 0x20>;
-			ti,hwmods = "counter_32k";
-		};
-
-		omap4_pmx_core: pinmux@4a100040 {
-			compatible = "ti,omap4-padconf", "pinctrl-single";
-			reg = <0x4a100040 0x0196>;
+		l4_cfg: l4@4a000000 {
+			compatible = "ti,omap4-l4-cfg", "simple-bus";
 			#address-cells = <1>;
-			#size-cells = <0>;
-			pinctrl-single,register-width = <16>;
-			pinctrl-single,function-mask = <0x7fff>;
+			#size-cells = <1>;
+			ranges = <0 0x4a000000 0x1000000>;
+
+			cm1: cm1@4000 {
+				compatible = "ti,omap4-cm1";
+				reg = <0x4000 0x2000>;
+
+				cm1_clocks: clocks {
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+
+				cm1_clockdomains: clockdomains {
+				};
+			};
+
+			cm2: cm2@8000 {
+				compatible = "ti,omap4-cm2";
+				reg = <0x8000 0x3000>;
+
+				cm2_clocks: clocks {
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+
+				cm2_clockdomains: clockdomains {
+				};
+			};
+
+			omap4_scm_core: scm@2000 {
+				compatible = "ti,omap4-scm-core", "simple-bus";
+				reg = <0x2000 0x1000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x2000 0x1000>;
+
+				scm_conf: scm_conf@0 {
+					compatible = "syscon";
+					reg = <0x0 0x800>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+				};
+			};
+
+			omap4_padconf_core: scm@100000 {
+				compatible = "ti,omap4-scm-padconf-core",
+					     "simple-bus";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x100000 0x1000>;
+
+				omap4_pmx_core: pinmux@40 {
+					compatible = "ti,omap4-padconf",
+						     "pinctrl-single";
+					reg = <0x40 0x0196>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					#interrupt-cells = <1>;
+					interrupt-controller;
+					pinctrl-single,register-width = <16>;
+					pinctrl-single,function-mask = <0x7fff>;
+				};
+
+				omap4_padconf_global: omap4_padconf_global@5a0 {
+					compatible = "syscon",
+						     "simple-bus";
+					reg = <0x5a0 0x170>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0 0x5a0 0x170>;
+
+					pbias_regulator: pbias_regulator {
+						compatible = "ti,pbias-omap4", "ti,pbias-omap";
+						reg = <0x60 0x4>;
+						syscon = <&omap4_padconf_global>;
+						pbias_mmc_reg: pbias_mmc_omap4 {
+							regulator-name = "pbias_mmc_omap4";
+							regulator-min-microvolt = <1800000>;
+							regulator-max-microvolt = <3000000>;
+						};
+					};
+				};
+			};
+
+			l4_wkup: l4@300000 {
+				compatible = "ti,omap4-l4-wkup", "simple-bus";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x300000 0x40000>;
+
+				counter32k: counter@4000 {
+					compatible = "ti,omap-counter32k";
+					reg = <0x4000 0x20>;
+					ti,hwmods = "counter_32k";
+				};
+
+				prm: prm@6000 {
+					compatible = "ti,omap4-prm";
+					reg = <0x6000 0x3000>;
+					interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+
+					prm_clocks: clocks {
+						#address-cells = <1>;
+						#size-cells = <0>;
+					};
+
+					prm_clockdomains: clockdomains {
+					};
+				};
+
+				scrm: scrm@a000 {
+					compatible = "ti,omap4-scrm";
+					reg = <0xa000 0x2000>;
+
+					scrm_clocks: clocks {
+						#address-cells = <1>;
+						#size-cells = <0>;
+					};
+
+					scrm_clockdomains: clockdomains {
+					};
+				};
+
+				omap4_pmx_wkup: pinmux@1e040 {
+					compatible = "ti,omap4-padconf",
+						     "pinctrl-single";
+					reg = <0x1e040 0x0038>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					#interrupt-cells = <1>;
+					interrupt-controller;
+					pinctrl-single,register-width = <16>;
+					pinctrl-single,function-mask = <0x7fff>;
+				};
+			};
 		};
-		omap4_pmx_wkup: pinmux@4a31e040 {
-			compatible = "ti,omap4-padconf", "pinctrl-single";
-			reg = <0x4a31e040 0x0038>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			pinctrl-single,register-width = <16>;
-			pinctrl-single,function-mask = <0x7fff>;
+
+		ocmcram: ocmcram@40304000 {
+			compatible = "mmio-sram";
+			reg = <0x40304000 0xa000>; /* 40k */
 		};
 
 		sdma: dma-controller@4a056000 {
 			compatible = "ti,omap4430-sdma";
 			reg = <0x4a056000 0x1000>;
-			interrupts = <0 12 0x4>,
-				     <0 13 0x4>,
-				     <0 14 0x4>,
-				     <0 15 0x4>;
+			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
 			#dma-cells = <1>;
-			#dma-channels = <32>;
-			#dma-requests = <127>;
+			dma-channels = <32>;
+			dma-requests = <127>;
 		};
 
 		gpio1: gpio@4a310000 {
 			compatible = "ti,omap4-gpio";
 			reg = <0x4a310000 0x200>;
-			interrupts = <0 29 0x4>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "gpio1";
 			ti,gpio-always-on;
 			gpio-controller;
@@ -150,7 +296,7 @@
 		gpio2: gpio@48055000 {
 			compatible = "ti,omap4-gpio";
 			reg = <0x48055000 0x200>;
-			interrupts = <0 30 0x4>;
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "gpio2";
 			gpio-controller;
 			#gpio-cells = <2>;
@@ -161,7 +307,7 @@
 		gpio3: gpio@48057000 {
 			compatible = "ti,omap4-gpio";
 			reg = <0x48057000 0x200>;
-			interrupts = <0 31 0x4>;
+			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "gpio3";
 			gpio-controller;
 			#gpio-cells = <2>;
@@ -172,7 +318,7 @@
 		gpio4: gpio@48059000 {
 			compatible = "ti,omap4-gpio";
 			reg = <0x48059000 0x200>;
-			interrupts = <0 32 0x4>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "gpio4";
 			gpio-controller;
 			#gpio-cells = <2>;
@@ -183,7 +329,7 @@
 		gpio5: gpio@4805b000 {
 			compatible = "ti,omap4-gpio";
 			reg = <0x4805b000 0x200>;
-			interrupts = <0 33 0x4>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "gpio5";
 			gpio-controller;
 			#gpio-cells = <2>;
@@ -194,7 +340,7 @@
 		gpio6: gpio@4805d000 {
 			compatible = "ti,omap4-gpio";
 			reg = <0x4805d000 0x200>;
-			interrupts = <0 34 0x4>;
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "gpio6";
 			gpio-controller;
 			#gpio-cells = <2>;
@@ -207,16 +353,19 @@
 			reg = <0x50000000 0x1000>;
 			#address-cells = <2>;
 			#size-cells = <1>;
-			interrupts = <0 20 0x4>;
+			interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 			gpmc,num-cs = <8>;
 			gpmc,num-waitpins = <4>;
 			ti,hwmods = "gpmc";
+			ti,no-idle-on-init;
+			clocks = <&l3_div_ck>;
+			clock-names = "fck";
 		};
 
 		uart1: serial@4806a000 {
 			compatible = "ti,omap4-uart";
 			reg = <0x4806a000 0x100>;
-			interrupts = <0 72 0x4>;
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "uart1";
 			clock-frequency = <48000000>;
 		};
@@ -224,7 +373,7 @@
 		uart2: serial@4806c000 {
 			compatible = "ti,omap4-uart";
 			reg = <0x4806c000 0x100>;
-			interrupts = <0 73 0x4>;
+			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "uart2";
 			clock-frequency = <48000000>;
 		};
@@ -232,7 +381,7 @@
 		uart3: serial@48020000 {
 			compatible = "ti,omap4-uart";
 			reg = <0x48020000 0x100>;
-			interrupts = <0 74 0x4>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "uart3";
 			clock-frequency = <48000000>;
 		};
@@ -240,15 +389,22 @@
 		uart4: serial@4806e000 {
 			compatible = "ti,omap4-uart";
 			reg = <0x4806e000 0x100>;
-			interrupts = <0 70 0x4>;
+			interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "uart4";
 			clock-frequency = <48000000>;
 		};
 
+		hwspinlock: spinlock@4a0f6000 {
+			compatible = "ti,omap4-hwspinlock";
+			reg = <0x4a0f6000 0x1000>;
+			ti,hwmods = "spinlock";
+			#hwlock-cells = <1>;
+		};
+
 		i2c1: i2c@48070000 {
 			compatible = "ti,omap4-i2c";
 			reg = <0x48070000 0x100>;
-			interrupts = <0 56 0x4>;
+			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "i2c1";
@@ -257,7 +413,7 @@
 		i2c2: i2c@48072000 {
 			compatible = "ti,omap4-i2c";
 			reg = <0x48072000 0x100>;
-			interrupts = <0 57 0x4>;
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "i2c2";
@@ -266,7 +422,7 @@
 		i2c3: i2c@48060000 {
 			compatible = "ti,omap4-i2c";
 			reg = <0x48060000 0x100>;
-			interrupts = <0 61 0x4>;
+			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "i2c3";
@@ -275,7 +431,7 @@
 		i2c4: i2c@48350000 {
 			compatible = "ti,omap4-i2c";
 			reg = <0x48350000 0x100>;
-			interrupts = <0 62 0x4>;
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "i2c4";
@@ -284,7 +440,7 @@
 		mcspi1: spi@48098000 {
 			compatible = "ti,omap4-mcspi";
 			reg = <0x48098000 0x200>;
-			interrupts = <0 65 0x4>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "mcspi1";
@@ -304,7 +460,7 @@
 		mcspi2: spi@4809a000 {
 			compatible = "ti,omap4-mcspi";
 			reg = <0x4809a000 0x200>;
-			interrupts = <0 66 0x4>;
+			interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "mcspi2";
@@ -319,7 +475,7 @@
 		mcspi3: spi@480b8000 {
 			compatible = "ti,omap4-mcspi";
 			reg = <0x480b8000 0x200>;
-			interrupts = <0 91 0x4>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "mcspi3";
@@ -331,7 +487,7 @@
 		mcspi4: spi@480ba000 {
 			compatible = "ti,omap4-mcspi";
 			reg = <0x480ba000 0x200>;
-			interrupts = <0 48 0x4>;
+			interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ti,hwmods = "mcspi4";
@@ -343,18 +499,19 @@
 		mmc1: mmc@4809c000 {
 			compatible = "ti,omap4-hsmmc";
 			reg = <0x4809c000 0x400>;
-			interrupts = <0 83 0x4>;
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "mmc1";
 			ti,dual-volt;
 			ti,needs-special-reset;
 			dmas = <&sdma 61>, <&sdma 62>;
 			dma-names = "tx", "rx";
+			pbias-supply = <&pbias_mmc_reg>;
 		};
 
 		mmc2: mmc@480b4000 {
 			compatible = "ti,omap4-hsmmc";
 			reg = <0x480b4000 0x400>;
-			interrupts = <0 86 0x4>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "mmc2";
 			ti,needs-special-reset;
 			dmas = <&sdma 47>, <&sdma 48>;
@@ -364,7 +521,7 @@
 		mmc3: mmc@480ad000 {
 			compatible = "ti,omap4-hsmmc";
 			reg = <0x480ad000 0x400>;
-			interrupts = <0 94 0x4>;
+			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "mmc3";
 			ti,needs-special-reset;
 			dmas = <&sdma 77>, <&sdma 78>;
@@ -374,7 +531,7 @@
 		mmc4: mmc@480d1000 {
 			compatible = "ti,omap4-hsmmc";
 			reg = <0x480d1000 0x400>;
-			interrupts = <0 96 0x4>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "mmc4";
 			ti,needs-special-reset;
 			dmas = <&sdma 57>, <&sdma 58>;
@@ -384,17 +541,34 @@
 		mmc5: mmc@480d5000 {
 			compatible = "ti,omap4-hsmmc";
 			reg = <0x480d5000 0x400>;
-			interrupts = <0 59 0x4>;
+			interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "mmc5";
 			ti,needs-special-reset;
 			dmas = <&sdma 59>, <&sdma 60>;
 			dma-names = "tx", "rx";
 		};
 
+		mmu_dsp: mmu@4a066000 {
+			compatible = "ti,omap4-iommu";
+			reg = <0x4a066000 0x100>;
+			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "mmu_dsp";
+			#iommu-cells = <0>;
+		};
+
+		mmu_ipu: mmu@55082000 {
+			compatible = "ti,omap4-iommu";
+			reg = <0x55082000 0x100>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "mmu_ipu";
+			#iommu-cells = <0>;
+			ti,iommu-bus-err-back;
+		};
+
 		wdt2: wdt@4a314000 {
 			compatible = "ti,omap4-wdt", "ti,omap3-wdt";
 			reg = <0x4a314000 0x80>;
-			interrupts = <0 80 0x4>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "wd_timer2";
 		};
 
@@ -403,11 +577,12 @@
 			reg = <0x40132000 0x7f>, /* MPU private access */
 			      <0x49032000 0x7f>; /* L3 Interconnect */
 			reg-names = "mpu", "dma";
-			interrupts = <0 112 0x4>;
+			interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "mcpdm";
 			dmas = <&sdma 65>,
 			       <&sdma 66>;
 			dma-names = "up_link", "dn_link";
+			status = "disabled";
 		};
 
 		dmic: dmic@4012e000 {
@@ -415,10 +590,11 @@
 			reg = <0x4012e000 0x7f>, /* MPU private access */
 			      <0x4902e000 0x7f>; /* L3 Interconnect */
 			reg-names = "mpu", "dma";
-			interrupts = <0 114 0x4>;
+			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "dmic";
 			dmas = <&sdma 67>;
 			dma-names = "up_link";
+			status = "disabled";
 		};
 
 		mcbsp1: mcbsp@40122000 {
@@ -426,13 +602,14 @@
 			reg = <0x40122000 0xff>, /* MPU private access */
 			      <0x49022000 0xff>; /* L3 Interconnect */
 			reg-names = "mpu", "dma";
-			interrupts = <0 17 0x4>;
+			interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "common";
 			ti,buffer-size = <128>;
 			ti,hwmods = "mcbsp1";
 			dmas = <&sdma 33>,
 			       <&sdma 34>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp2: mcbsp@40124000 {
@@ -440,13 +617,14 @@
 			reg = <0x40124000 0xff>, /* MPU private access */
 			      <0x49024000 0xff>; /* L3 Interconnect */
 			reg-names = "mpu", "dma";
-			interrupts = <0 22 0x4>;
+			interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "common";
 			ti,buffer-size = <128>;
 			ti,hwmods = "mcbsp2";
 			dmas = <&sdma 17>,
 			       <&sdma 18>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp3: mcbsp@40126000 {
@@ -454,41 +632,51 @@
 			reg = <0x40126000 0xff>, /* MPU private access */
 			      <0x49026000 0xff>; /* L3 Interconnect */
 			reg-names = "mpu", "dma";
-			interrupts = <0 23 0x4>;
+			interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "common";
 			ti,buffer-size = <128>;
 			ti,hwmods = "mcbsp3";
 			dmas = <&sdma 19>,
 			       <&sdma 20>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp4: mcbsp@48096000 {
 			compatible = "ti,omap4-mcbsp";
 			reg = <0x48096000 0xff>; /* L4 Interconnect */
 			reg-names = "mpu";
-			interrupts = <0 16 0x4>;
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "common";
 			ti,buffer-size = <128>;
 			ti,hwmods = "mcbsp4";
 			dmas = <&sdma 31>,
 			       <&sdma 32>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		keypad: keypad@4a31c000 {
 			compatible = "ti,omap4-keypad";
 			reg = <0x4a31c000 0x80>;
-			interrupts = <0 120 0x4>;
+			interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
 			reg-names = "mpu";
 			ti,hwmods = "kbd";
 		};
 
+		dmm@4e000000 {
+			compatible = "ti,omap4-dmm";
+			reg = <0x4e000000 0x800>;
+			interrupts = <0 113 0x4>;
+			ti,hwmods = "dmm";
+		};
+
 		emif1: emif@4c000000 {
 			compatible = "ti,emif-4d";
 			reg = <0x4c000000 0x100>;
-			interrupts = <0 110 0x4>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "emif1";
+			ti,no-idle-on-init;
 			phy-type = <1>;
 			hw-caps-read-idle-ctrl;
 			hw-caps-ll-interface;
@@ -498,8 +686,9 @@
 		emif2: emif@4d000000 {
 			compatible = "ti,emif-4d";
 			reg = <0x4d000000 0x100>;
-			interrupts = <0 111 0x4>;
+			interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "emif2";
+			ti,no-idle-on-init;
 			phy-type = <1>;
 			hw-caps-read-idle-ctrl;
 			hw-caps-ll-interface;
@@ -516,14 +705,35 @@
 			usb2_phy: usb2phy@4a0ad080 {
 				compatible = "ti,omap-usb2";
 				reg = <0x4a0ad080 0x58>;
-				ctrl-module = <&omap_control_usb>;
+				ctrl-module = <&omap_control_usb2phy>;
+				clocks = <&usb_phy_cm_clk32k>;
+				clock-names = "wkupclk";
+				#phy-cells = <0>;
+			};
+		};
+
+		mailbox: mailbox@4a0f4000 {
+			compatible = "ti,omap4-mailbox";
+			reg = <0x4a0f4000 0x200>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "mailbox";
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <3>;
+			ti,mbox-num-fifos = <8>;
+			mbox_ipu: mbox_ipu {
+				ti,mbox-tx = <0 0 0>;
+				ti,mbox-rx = <1 0 0>;
+			};
+			mbox_dsp: mbox_dsp {
+				ti,mbox-tx = <3 0 0>;
+				ti,mbox-rx = <2 0 0>;
 			};
 		};
 
 		timer1: timer@4a318000 {
 			compatible = "ti,omap3430-timer";
 			reg = <0x4a318000 0x80>;
-			interrupts = <0 37 0x4>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "timer1";
 			ti,timer-alwon;
 		};
@@ -531,21 +741,21 @@
 		timer2: timer@48032000 {
 			compatible = "ti,omap3430-timer";
 			reg = <0x48032000 0x80>;
-			interrupts = <0 38 0x4>;
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "timer2";
 		};
 
 		timer3: timer@48034000 {
 			compatible = "ti,omap4430-timer";
 			reg = <0x48034000 0x80>;
-			interrupts = <0 39 0x4>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "timer3";
 		};
 
 		timer4: timer@48036000 {
 			compatible = "ti,omap4430-timer";
 			reg = <0x48036000 0x80>;
-			interrupts = <0 40 0x4>;
+			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "timer4";
 		};
 
@@ -553,7 +763,7 @@
 			compatible = "ti,omap4430-timer";
 			reg = <0x40138000 0x80>,
 			      <0x49038000 0x80>;
-			interrupts = <0 41 0x4>;
+			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "timer5";
 			ti,timer-dsp;
 		};
@@ -562,7 +772,7 @@
 			compatible = "ti,omap4430-timer";
 			reg = <0x4013a000 0x80>,
 			      <0x4903a000 0x80>;
-			interrupts = <0 42 0x4>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "timer6";
 			ti,timer-dsp;
 		};
@@ -571,7 +781,7 @@
 			compatible = "ti,omap4430-timer";
 			reg = <0x4013c000 0x80>,
 			      <0x4903c000 0x80>;
-			interrupts = <0 43 0x4>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "timer7";
 			ti,timer-dsp;
 		};
@@ -580,7 +790,7 @@
 			compatible = "ti,omap4430-timer";
 			reg = <0x4013e000 0x80>,
 			      <0x4903e000 0x80>;
-			interrupts = <0 44 0x4>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "timer8";
 			ti,timer-pwm;
 			ti,timer-dsp;
@@ -589,7 +799,7 @@
 		timer9: timer@4803e000 {
 			compatible = "ti,omap4430-timer";
 			reg = <0x4803e000 0x80>;
-			interrupts = <0 45 0x4>;
+			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "timer9";
 			ti,timer-pwm;
 		};
@@ -597,7 +807,7 @@
 		timer10: timer@48086000 {
 			compatible = "ti,omap3430-timer";
 			reg = <0x48086000 0x80>;
-			interrupts = <0 46 0x4>;
+			interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "timer10";
 			ti,timer-pwm;
 		};
@@ -605,7 +815,7 @@
 		timer11: timer@48088000 {
 			compatible = "ti,omap4430-timer";
 			reg = <0x48088000 0x80>;
-			interrupts = <0 47 0x4>;
+			interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "timer11";
 			ti,timer-pwm;
 		};
@@ -613,7 +823,7 @@
 		usbhstll: usbhstll@4a062000 {
 			compatible = "ti,usbhs-tll";
 			reg = <0x4a062000 0x1000>;
-			interrupts = <0 78 0x4>;
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "usb_tll_hs";
 		};
 
@@ -624,41 +834,180 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
+			clocks = <&init_60m_fclk>,
+				 <&xclk60mhsp1_ck>,
+				 <&xclk60mhsp2_ck>;
+			clock-names = "refclk_60m_int",
+				      "refclk_60m_ext_p1",
+				      "refclk_60m_ext_p2";
 
 			usbhsohci: ohci@4a064800 {
-				compatible = "ti,ohci-omap3", "usb-ohci";
+				compatible = "ti,ohci-omap3";
 				reg = <0x4a064800 0x400>;
 				interrupt-parent = <&gic>;
-				interrupts = <0 76 0x4>;
+				interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			usbhsehci: ehci@4a064c00 {
-				compatible = "ti,ehci-omap", "usb-ehci";
+				compatible = "ti,ehci-omap";
 				reg = <0x4a064c00 0x400>;
 				interrupt-parent = <&gic>;
-				interrupts = <0 77 0x4>;
+				interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 
-		omap_control_usb: omap-control-usb@4a002300 {
-			compatible = "ti,omap-control-usb";
-			reg = <0x4a002300 0x4>,
-			      <0x4a00233c 0x4>;
-			reg-names = "control_dev_conf", "otghs_control";
-			ti,type = <1>;
+		omap_control_usb2phy: control-phy@4a002300 {
+			compatible = "ti,control-phy-usb2";
+			reg = <0x4a002300 0x4>;
+			reg-names = "power";
+		};
+
+		omap_control_usbotg: control-phy@4a00233c {
+			compatible = "ti,control-phy-otghs";
+			reg = <0x4a00233c 0x4>;
+			reg-names = "otghs_control";
 		};
 
 		usb_otg_hs: usb_otg_hs@4a0ab000 {
 			compatible = "ti,omap4-musb";
 			reg = <0x4a0ab000 0x7ff>;
-			interrupts = <0 92 0x4>, <0 93 0x4>;
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "mc", "dma";
 			ti,hwmods = "usb_otg_hs";
 			usb-phy = <&usb2_phy>;
+			phys = <&usb2_phy>;
+			phy-names = "usb2-phy";
 			multipoint = <1>;
 			num-eps = <16>;
 			ram-bits = <12>;
-			ti,has-mailbox;
+			ctrl-module = <&omap_control_usbotg>;
+		};
+
+		aes: aes@4b501000 {
+			compatible = "ti,omap4-aes";
+			ti,hwmods = "aes";
+			reg = <0x4b501000 0xa0>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&sdma 111>, <&sdma 110>;
+			dma-names = "tx", "rx";
+		};
+
+		des: des@480a5000 {
+			compatible = "ti,omap4-des";
+			ti,hwmods = "des";
+			reg = <0x480a5000 0xa0>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&sdma 117>, <&sdma 116>;
+			dma-names = "tx", "rx";
+		};
+
+		abb_mpu: regulator-abb-mpu {
+			compatible = "ti,abb-v2";
+			regulator-name = "abb_mpu";
+			#address-cells = <0>;
+			#size-cells = <0>;
+			ti,tranxdone-status-mask = <0x80>;
+			clocks = <&sys_clkin_ck>;
+			ti,settling-time = <50>;
+			ti,clock-cycles = <16>;
+
+			status = "disabled";
+		};
+
+		abb_iva: regulator-abb-iva {
+			compatible = "ti,abb-v2";
+			regulator-name = "abb_iva";
+			#address-cells = <0>;
+			#size-cells = <0>;
+			ti,tranxdone-status-mask = <0x80000000>;
+			clocks = <&sys_clkin_ck>;
+			ti,settling-time = <50>;
+			ti,clock-cycles = <16>;
+
+			status = "disabled";
+		};
+
+		dss: dss@58000000 {
+			compatible = "ti,omap4-dss";
+			reg = <0x58000000 0x80>;
+			status = "disabled";
+			ti,hwmods = "dss_core";
+			clocks = <&dss_dss_clk>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			dispc@58001000 {
+				compatible = "ti,omap4-dispc";
+				reg = <0x58001000 0x1000>;
+				interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+				ti,hwmods = "dss_dispc";
+				clocks = <&dss_dss_clk>;
+				clock-names = "fck";
+			};
+
+			rfbi: encoder@58002000  {
+				compatible = "ti,omap4-rfbi";
+				reg = <0x58002000 0x1000>;
+				status = "disabled";
+				ti,hwmods = "dss_rfbi";
+				clocks = <&dss_dss_clk>, <&l3_div_ck>;
+				clock-names = "fck", "ick";
+			};
+
+			venc: encoder@58003000 {
+				compatible = "ti,omap4-venc";
+				reg = <0x58003000 0x1000>;
+				status = "disabled";
+				ti,hwmods = "dss_venc";
+				clocks = <&dss_tv_clk>;
+				clock-names = "fck";
+			};
+
+			dsi1: encoder@58004000 {
+				compatible = "ti,omap4-dsi";
+				reg = <0x58004000 0x200>,
+				      <0x58004200 0x40>,
+				      <0x58004300 0x20>;
+				reg-names = "proto", "phy", "pll";
+				interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+				ti,hwmods = "dss_dsi1";
+				clocks = <&dss_dss_clk>, <&dss_sys_clk>;
+				clock-names = "fck", "sys_clk";
+			};
+
+			dsi2: encoder@58005000 {
+				compatible = "ti,omap4-dsi";
+				reg = <0x58005000 0x200>,
+				      <0x58005200 0x40>,
+				      <0x58005300 0x20>;
+				reg-names = "proto", "phy", "pll";
+				interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+				ti,hwmods = "dss_dsi2";
+				clocks = <&dss_dss_clk>, <&dss_sys_clk>;
+				clock-names = "fck", "sys_clk";
+			};
+
+			hdmi: encoder@58006000 {
+				compatible = "ti,omap4-hdmi";
+				reg = <0x58006000 0x200>,
+				      <0x58006200 0x100>,
+				      <0x58006300 0x100>,
+				      <0x58006400 0x1000>;
+				reg-names = "wp", "pll", "phy", "core";
+				interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+				ti,hwmods = "dss_hdmi";
+				clocks = <&dss_48mhz_clk>, <&dss_sys_clk>;
+				clock-names = "fck", "sys_clk";
+				dmas = <&sdma 76>;
+				dma-names = "audio_tx";
+			};
 		};
 	};
 };
+
+/include/ "omap44xx-clocks.dtsi"