--- zzzz-none-000/linux-3.10.107/arch/arm/mach-davinci/board-dm355-evm.c	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/arch/arm/mach-davinci/board-dm355-evm.c	2021-02-04 17:41:59.000000000 +0000
@@ -22,15 +22,17 @@
 #include <media/tvp514x.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/eeprom.h>
+#include <linux/platform_data/gpio-davinci.h>
+#include <linux/platform_data/i2c-davinci.h>
+#include <linux/platform_data/mtd-davinci.h>
+#include <linux/platform_data/mmc-davinci.h>
+#include <linux/platform_data/usb-davinci.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 
-#include <linux/platform_data/i2c-davinci.h>
 #include <mach/serial.h>
-#include <linux/platform_data/mtd-davinci.h>
-#include <linux/platform_data/mmc-davinci.h>
-#include <linux/platform_data/usb-davinci.h>
+#include <mach/common.h>
 
 #include "davinci.h"
 
@@ -292,7 +294,7 @@
 		.default_mode	= "ntsc",
 		.num_modes	= ARRAY_SIZE(dm355evm_enc_preset_timing),
 		.modes		= dm355evm_enc_preset_timing,
-		.if_params	= V4L2_MBUS_FMT_FIXED,
+		.if_params	= MEDIA_BUS_FMT_FIXED,
 	},
 };
 
@@ -314,10 +316,6 @@
 	&davinci_nand_device,
 };
 
-static struct davinci_uart_config uart_config __initdata = {
-	.enabled_uarts = (1 << 0),
-};
-
 static void __init dm355_evm_map_io(void)
 {
 	dm355_init();
@@ -352,11 +350,7 @@
  * you have proper Mini-B or Mini-A cables (or Mini-A adapters)
  * the ID pin won't need any help.
  */
-#ifdef CONFIG_USB_MUSB_PERIPHERAL
-#define USB_ID_VALUE	0	/* ID pulled high; *should* float */
-#else
 #define USB_ID_VALUE	1	/* ID pulled low */
-#endif
 
 static struct spi_eeprom at25640a = {
 	.byte_len	= SZ_64K / 8,
@@ -379,6 +373,11 @@
 static __init void dm355_evm_init(void)
 {
 	struct clk *aemif;
+	int ret;
+
+	ret = dm355_gpio_register();
+	if (ret)
+		pr_warn("%s: GPIO init failed: %d\n", __func__, ret);
 
 	gpio_request(1, "dm9000");
 	gpio_direction_input(1);
@@ -393,7 +392,7 @@
 	platform_add_devices(davinci_evm_devices,
 			     ARRAY_SIZE(davinci_evm_devices));
 	evm_init_i2c();
-	davinci_serial_init(&uart_config);
+	davinci_serial_init(dm355_serial_device);
 
 	/* NOTE:  NAND flash timings set by the UBL are slower than
 	 * needed by MT29F16G08FAA chips ... EMIF.A1CR is 0x40400204