--- zzzz-none-000/linux-3.10.107/arch/arm/mach-ixp4xx/dsmg600-setup.c	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/arch/arm/mach-ixp4xx/dsmg600-setup.c	2021-02-04 17:41:59.000000000 +0000
@@ -26,6 +26,9 @@
 #include <linux/reboot.h>
 #include <linux/i2c.h>
 #include <linux/i2c-gpio.h>
+#include <linux/gpio.h>
+
+#include <mach/hardware.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -159,11 +162,8 @@
 
 static void dsmg600_power_off(void)
 {
-	/* enable the pwr cntl gpio */
-	gpio_line_config(DSMG600_PO_GPIO, IXP4XX_GPIO_OUT);
-
-	/* poweroff */
-	gpio_line_set(DSMG600_PO_GPIO, IXP4XX_GPIO_HIGH);
+	/* enable the pwr cntl and drive it high */
+	gpio_direction_output(DSMG600_PO_GPIO, 1);
 }
 
 /* This is used to make sure the power-button pusher is serious.  The button
@@ -200,7 +200,7 @@
 			ctrl_alt_del();
 
 			/* Change the state of the power LED to "blink" */
-			gpio_line_set(DSMG600_LED_PWR_GPIO, IXP4XX_GPIO_LOW);
+			gpio_set_value(DSMG600_LED_PWR_GPIO, 0);
 		} else {
 			power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
 		}
@@ -226,6 +226,39 @@
     ixp4xx_timer_init();
 }
 
+static int __init dsmg600_gpio_init(void)
+{
+	if (!machine_is_dsmg600())
+		return 0;
+
+	gpio_request(DSMG600_RB_GPIO, "reset button");
+	if (request_irq(gpio_to_irq(DSMG600_RB_GPIO), &dsmg600_reset_handler,
+		IRQF_TRIGGER_LOW, "DSM-G600 reset button", NULL) < 0) {
+
+		printk(KERN_DEBUG "Reset Button IRQ %d not available\n",
+			gpio_to_irq(DSMG600_RB_GPIO));
+	}
+
+	/*
+	 * The power button on the D-Link DSM-G600 is on GPIO 15, but
+	 * it cannot handle interrupts on that GPIO line.  So we'll
+	 * have to poll it with a kernel timer.
+	 */
+
+	/* Make sure that the power button GPIO is set up as an input */
+	gpio_request(DSMG600_PB_GPIO, "power button");
+	gpio_direction_input(DSMG600_PB_GPIO);
+	/* Request poweroff GPIO line */
+	gpio_request(DSMG600_PO_GPIO, "power off button");
+
+	/* Set the initial value for the power button IRQ handler */
+	power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
+
+	mod_timer(&dsmg600_power_timer, jiffies + msecs_to_jiffies(500));
+	return 0;
+}
+device_initcall(dsmg600_gpio_init);
+
 static void __init dsmg600_init(void)
 {
 	ixp4xx_sys_init();
@@ -249,27 +282,6 @@
 	platform_add_devices(dsmg600_devices, ARRAY_SIZE(dsmg600_devices));
 
 	pm_power_off = dsmg600_power_off;
-
-	if (request_irq(gpio_to_irq(DSMG600_RB_GPIO), &dsmg600_reset_handler,
-		IRQF_DISABLED | IRQF_TRIGGER_LOW,
-		"DSM-G600 reset button", NULL) < 0) {
-
-		printk(KERN_DEBUG "Reset Button IRQ %d not available\n",
-			gpio_to_irq(DSMG600_RB_GPIO));
-	}
-
-	/* The power button on the D-Link DSM-G600 is on GPIO 15, but
-	 * it cannot handle interrupts on that GPIO line.  So we'll
-	 * have to poll it with a kernel timer.
-	 */
-
-	/* Make sure that the power button GPIO is set up as an input */
-	gpio_line_config(DSMG600_PB_GPIO, IXP4XX_GPIO_IN);
-
-	/* Set the initial value for the power button IRQ handler */
-	power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
-
-	mod_timer(&dsmg600_power_timer, jiffies + msecs_to_jiffies(500));
 }
 
 MACHINE_START(DSMG600, "D-Link DSM-G600 RevA")