--- zzzz-none-000/linux-3.10.107/arch/arm/mach-omap2/prm2xxx_3xxx.c	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/arch/arm/mach-omap2/prm2xxx_3xxx.c	2021-02-04 17:41:59.000000000 +0000
@@ -16,7 +16,6 @@
 #include <linux/err.h>
 #include <linux/io.h>
 
-#include "common.h"
 #include "powerdomain.h"
 #include "prm2xxx_3xxx.h"
 #include "prm-regbits-24xx.h"
@@ -25,14 +24,16 @@
 /**
  * omap2_prm_is_hardreset_asserted - read the HW reset line state of
  * submodules contained in the hwmod module
- * @prm_mod: PRM submodule base (e.g. CORE_MOD)
  * @shift: register bit shift corresponding to the reset line to check
+ * @part: PRM partition, ignored for OMAP2
+ * @prm_mod: PRM submodule base (e.g. CORE_MOD)
+ * @offset: register offset, ignored for OMAP2
  *
  * Returns 1 if the (sub)module hardreset line is currently asserted,
  * 0 if the (sub)module hardreset line is not currently asserted, or
  * -EINVAL if called while running on a non-OMAP2/3 chip.
  */
-int omap2_prm_is_hardreset_asserted(s16 prm_mod, u8 shift)
+int omap2_prm_is_hardreset_asserted(u8 shift, u8 part, s16 prm_mod, u16 offset)
 {
 	return omap2_prm_read_mod_bits_shift(prm_mod, OMAP2_RM_RSTCTRL,
 				       (1 << shift));
@@ -40,8 +41,10 @@
 
 /**
  * omap2_prm_assert_hardreset - assert the HW reset line of a submodule
- * @prm_mod: PRM submodule base (e.g. CORE_MOD)
  * @shift: register bit shift corresponding to the reset line to assert
+ * @part: PRM partition, ignored for OMAP2
+ * @prm_mod: PRM submodule base (e.g. CORE_MOD)
+ * @offset: register offset, ignored for OMAP2
  *
  * Some IPs like dsp or iva contain processors that require an HW
  * reset line to be asserted / deasserted in order to fully enable the
@@ -50,7 +53,7 @@
  * place the submodule into reset.  Returns 0 upon success or -EINVAL
  * upon an argument error.
  */
-int omap2_prm_assert_hardreset(s16 prm_mod, u8 shift)
+int omap2_prm_assert_hardreset(u8 shift, u8 part, s16 prm_mod, u16 offset)
 {
 	u32 mask;
 
@@ -65,6 +68,10 @@
  * @prm_mod: PRM submodule base (e.g. CORE_MOD)
  * @rst_shift: register bit shift corresponding to the reset line to deassert
  * @st_shift: register bit shift for the status of the deasserted submodule
+ * @part: PRM partition, not used for OMAP2
+ * @prm_mod: PRM submodule base (e.g. CORE_MOD)
+ * @rst_offset: reset register offset, not used for OMAP2
+ * @st_offset: reset status register offset, not used for OMAP2
  *
  * Some IPs like dsp or iva contain processors that require an HW
  * reset line to be asserted / deasserted in order to fully enable the
@@ -75,7 +82,8 @@
  * -EINVAL upon an argument error, -EEXIST if the submodule was already out
  * of reset, or -EBUSY if the submodule did not exit reset promptly.
  */
-int omap2_prm_deassert_hardreset(s16 prm_mod, u8 rst_shift, u8 st_shift)
+int omap2_prm_deassert_hardreset(u8 rst_shift, u8 st_shift, u8 part,
+				 s16 prm_mod, u16 rst_offset, u16 st_offset)
 {
 	u32 rst, st;
 	int c;