--- zzzz-none-000/linux-3.10.107/arch/arm/mach-omap2/usb-host.c	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/arch/arm/mach-omap2/usb-host.c	2021-02-04 17:41:59.000000000 +0000
@@ -28,6 +28,7 @@
 #include <linux/io.h>
 #include <linux/gpio.h>
 #include <linux/usb/phy.h>
+#include <linux/usb/usb_phy_generic.h>
 
 #include "soc.h"
 #include "omap_device.h"
@@ -188,125 +189,6 @@
 	return;
 }
 
-static
-void __init setup_4430ehci_io_mux(const enum usbhs_omap_port_mode *port_mode)
-{
-	switch (port_mode[0]) {
-	case OMAP_EHCI_PORT_MODE_PHY:
-		omap_mux_init_signal("usbb1_ulpiphy_stp",
-			OMAP_PIN_OUTPUT);
-		omap_mux_init_signal("usbb1_ulpiphy_clk",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb1_ulpiphy_dir",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb1_ulpiphy_nxt",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb1_ulpiphy_dat0",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb1_ulpiphy_dat1",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb1_ulpiphy_dat2",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb1_ulpiphy_dat3",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb1_ulpiphy_dat4",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb1_ulpiphy_dat5",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb1_ulpiphy_dat6",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb1_ulpiphy_dat7",
-			OMAP_PIN_INPUT_PULLDOWN);
-			break;
-	case OMAP_EHCI_PORT_MODE_TLL:
-		omap_mux_init_signal("usbb1_ulpitll_stp",
-			OMAP_PIN_INPUT_PULLUP);
-		omap_mux_init_signal("usbb1_ulpitll_clk",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb1_ulpitll_dir",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb1_ulpitll_nxt",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb1_ulpitll_dat0",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb1_ulpitll_dat1",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb1_ulpitll_dat2",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb1_ulpitll_dat3",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb1_ulpitll_dat4",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb1_ulpitll_dat5",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb1_ulpitll_dat6",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb1_ulpitll_dat7",
-			OMAP_PIN_INPUT_PULLDOWN);
-			break;
-	case OMAP_USBHS_PORT_MODE_UNUSED:
-	default:
-			break;
-	}
-	switch (port_mode[1]) {
-	case OMAP_EHCI_PORT_MODE_PHY:
-		omap_mux_init_signal("usbb2_ulpiphy_stp",
-			OMAP_PIN_OUTPUT);
-		omap_mux_init_signal("usbb2_ulpiphy_clk",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb2_ulpiphy_dir",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb2_ulpiphy_nxt",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb2_ulpiphy_dat0",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb2_ulpiphy_dat1",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb2_ulpiphy_dat2",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb2_ulpiphy_dat3",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb2_ulpiphy_dat4",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb2_ulpiphy_dat5",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb2_ulpiphy_dat6",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb2_ulpiphy_dat7",
-			OMAP_PIN_INPUT_PULLDOWN);
-			break;
-	case OMAP_EHCI_PORT_MODE_TLL:
-		omap_mux_init_signal("usbb2_ulpitll_stp",
-			OMAP_PIN_INPUT_PULLUP);
-		omap_mux_init_signal("usbb2_ulpitll_clk",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb2_ulpitll_dir",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb2_ulpitll_nxt",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb2_ulpitll_dat0",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb2_ulpitll_dat1",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb2_ulpitll_dat2",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb2_ulpitll_dat3",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb2_ulpitll_dat4",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb2_ulpitll_dat5",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb2_ulpitll_dat6",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb2_ulpitll_dat7",
-			OMAP_PIN_INPUT_PULLDOWN);
-			break;
-	case OMAP_USBHS_PORT_MODE_UNUSED:
-	default:
-			break;
-	}
-}
-
 static void __init setup_ohci_io_mux(const enum usbhs_omap_port_mode *port_mode)
 {
 	switch (port_mode[0]) {
@@ -404,78 +286,6 @@
 	}
 }
 
-static
-void __init setup_4430ohci_io_mux(const enum usbhs_omap_port_mode *port_mode)
-{
-	switch (port_mode[0]) {
-	case OMAP_OHCI_PORT_MODE_PHY_6PIN_DATSE0:
-	case OMAP_OHCI_PORT_MODE_PHY_6PIN_DPDM:
-	case OMAP_OHCI_PORT_MODE_TLL_6PIN_DATSE0:
-	case OMAP_OHCI_PORT_MODE_TLL_6PIN_DPDM:
-		omap_mux_init_signal("usbb1_mm_rxdp",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb1_mm_rxdm",
-			OMAP_PIN_INPUT_PULLDOWN);
-
-	case OMAP_OHCI_PORT_MODE_PHY_4PIN_DPDM:
-	case OMAP_OHCI_PORT_MODE_TLL_4PIN_DPDM:
-		omap_mux_init_signal("usbb1_mm_rxrcv",
-			OMAP_PIN_INPUT_PULLDOWN);
-
-	case OMAP_OHCI_PORT_MODE_PHY_3PIN_DATSE0:
-	case OMAP_OHCI_PORT_MODE_TLL_3PIN_DATSE0:
-		omap_mux_init_signal("usbb1_mm_txen",
-			OMAP_PIN_INPUT_PULLDOWN);
-
-
-	case OMAP_OHCI_PORT_MODE_TLL_2PIN_DATSE0:
-	case OMAP_OHCI_PORT_MODE_TLL_2PIN_DPDM:
-		omap_mux_init_signal("usbb1_mm_txdat",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb1_mm_txse0",
-			OMAP_PIN_INPUT_PULLDOWN);
-		break;
-
-	case OMAP_USBHS_PORT_MODE_UNUSED:
-	default:
-		break;
-	}
-
-	switch (port_mode[1]) {
-	case OMAP_OHCI_PORT_MODE_PHY_6PIN_DATSE0:
-	case OMAP_OHCI_PORT_MODE_PHY_6PIN_DPDM:
-	case OMAP_OHCI_PORT_MODE_TLL_6PIN_DATSE0:
-	case OMAP_OHCI_PORT_MODE_TLL_6PIN_DPDM:
-		omap_mux_init_signal("usbb2_mm_rxdp",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb2_mm_rxdm",
-			OMAP_PIN_INPUT_PULLDOWN);
-
-	case OMAP_OHCI_PORT_MODE_PHY_4PIN_DPDM:
-	case OMAP_OHCI_PORT_MODE_TLL_4PIN_DPDM:
-		omap_mux_init_signal("usbb2_mm_rxrcv",
-			OMAP_PIN_INPUT_PULLDOWN);
-
-	case OMAP_OHCI_PORT_MODE_PHY_3PIN_DATSE0:
-	case OMAP_OHCI_PORT_MODE_TLL_3PIN_DATSE0:
-		omap_mux_init_signal("usbb2_mm_txen",
-			OMAP_PIN_INPUT_PULLDOWN);
-
-
-	case OMAP_OHCI_PORT_MODE_TLL_2PIN_DATSE0:
-	case OMAP_OHCI_PORT_MODE_TLL_2PIN_DPDM:
-		omap_mux_init_signal("usbb2_mm_txdat",
-			OMAP_PIN_INPUT_PULLDOWN);
-		omap_mux_init_signal("usbb2_mm_txse0",
-			OMAP_PIN_INPUT_PULLDOWN);
-		break;
-
-	case OMAP_USBHS_PORT_MODE_UNUSED:
-	default:
-		break;
-	}
-}
-
 void __init usbhs_init(struct usbhs_omap_platform_data *pdata)
 {
 	struct omap_hwmod	*uhh_hwm, *tll_hwm;
@@ -489,9 +299,6 @@
 		if (omap_rev() <= OMAP3430_REV_ES2_1)
 			pdata->single_ulpi_bypass = true;
 
-	} else if (cpu_is_omap44xx()) {
-		setup_4430ehci_io_mux(pdata->port_mode);
-		setup_4430ohci_io_mux(pdata->port_mode);
 	}
 
 	uhh_hwm = omap_hwmod_lookup(USBHS_UHH_HWMODNAME);
@@ -542,7 +349,7 @@
 	/* .init_data filled later */
 };
 
-static const char *nop_name = "nop_usb_xceiv"; /* NOP PHY driver */
+static const char *nop_name = "usb_phy_generic"; /* NOP PHY driver */
 static const char *reg_name = "reg-fixed-voltage"; /* Regulator driver */
 
 /**
@@ -560,7 +367,8 @@
 	struct regulator_init_data *reg_data;
 	struct fixed_voltage_config *config;
 	struct platform_device *pdev;
-	int ret;
+	struct platform_device_info pdevinfo;
+	int ret = -ENOMEM;
 
 	supplies = kzalloc(sizeof(*supplies), GFP_KERNEL);
 	if (!supplies)
@@ -571,7 +379,7 @@
 
 	reg_data = kzalloc(sizeof(*reg_data), GFP_KERNEL);
 	if (!reg_data)
-		return -ENOMEM;
+		goto err_data;
 
 	reg_data->constraints.valid_ops_mask = REGULATOR_CHANGE_STATUS;
 	reg_data->consumer_supplies = supplies;
@@ -580,39 +388,54 @@
 	config = kmemdup(&hsusb_reg_config, sizeof(hsusb_reg_config),
 			GFP_KERNEL);
 	if (!config)
-		return -ENOMEM;
+		goto err_config;
+
+	config->supply_name = kstrdup(name, GFP_KERNEL);
+	if (!config->supply_name)
+		goto err_supplyname;
 
-	config->supply_name = name;
 	config->gpio = gpio;
 	config->enable_high = polarity;
 	config->init_data = reg_data;
 
 	/* create a regulator device */
-	pdev = kzalloc(sizeof(*pdev), GFP_KERNEL);
-	if (!pdev)
-		return -ENOMEM;
-
-	pdev->id = PLATFORM_DEVID_AUTO;
-	pdev->name = reg_name;
-	pdev->dev.platform_data = config;
-
-	ret = platform_device_register(pdev);
-	if (ret)
-		pr_err("%s: Failed registering regulator %s for %s\n",
-				__func__, name, dev_id);
+	memset(&pdevinfo, 0, sizeof(pdevinfo));
+	pdevinfo.name = reg_name;
+	pdevinfo.id = PLATFORM_DEVID_AUTO;
+	pdevinfo.data = config;
+	pdevinfo.size_data = sizeof(*config);
 
+	pdev = platform_device_register_full(&pdevinfo);
+	if (IS_ERR(pdev)) {
+		ret = PTR_ERR(pdev);
+		pr_err("%s: Failed registering regulator %s for %s : %d\n",
+				__func__, name, dev_id, ret);
+		goto err_register;
+	}
+
+	return 0;
+
+err_register:
+	kfree(config->supply_name);
+err_supplyname:
+	kfree(config);
+err_config:
+	kfree(reg_data);
+err_data:
+	kfree(supplies);
 	return ret;
 }
 
+#define MAX_STR 20
+
 int usbhs_init_phys(struct usbhs_phy_data *phy, int num_phys)
 {
-	char *rail_name;
-	int i, len;
+	char rail_name[MAX_STR];
+	int i;
 	struct platform_device *pdev;
 	char *phy_id;
-
-	/* the phy_id will be something like "nop_usb_xceiv.1" */
-	len = strlen(nop_name) + 3; /* 3 -> ".1" and NULL terminator */
+	struct platform_device_info pdevinfo;
+	struct usb_phy_generic_platform_data nop_pdata;
 
 	for (i = 0; i < num_phys; i++) {
 
@@ -627,52 +450,41 @@
 			!gpio_is_valid(phy->vcc_gpio))
 			continue;
 
-		/* create a NOP PHY device */
-		pdev = kzalloc(sizeof(*pdev), GFP_KERNEL);
-		if (!pdev)
-			return -ENOMEM;
-
-		pdev->id = phy->port;
-		pdev->name = nop_name;
-		pdev->dev.platform_data = phy->platform_data;
-
-		phy_id = kmalloc(len, GFP_KERNEL);
-		if (!phy_id)
+		phy_id = kmalloc(MAX_STR, GFP_KERNEL);
+		if (!phy_id) {
+			pr_err("%s: kmalloc() failed\n", __func__);
 			return -ENOMEM;
+		}
 
-		scnprintf(phy_id, len, "nop_usb_xceiv.%d\n",
-					pdev->id);
+		/* set platform data */
+		memset(&nop_pdata, 0, sizeof(nop_pdata));
+		if (gpio_is_valid(phy->vcc_gpio))
+			nop_pdata.needs_vcc = true;
+		nop_pdata.gpio_reset = phy->reset_gpio;
+		nop_pdata.type = USB_PHY_TYPE_USB2;
 
-		if (platform_device_register(pdev)) {
-			pr_err("%s: Failed to register device %s\n",
-				__func__,  phy_id);
+		/* create a NOP PHY device */
+		memset(&pdevinfo, 0, sizeof(pdevinfo));
+		pdevinfo.name = nop_name;
+		pdevinfo.id = phy->port;
+		pdevinfo.data = &nop_pdata;
+		pdevinfo.size_data =
+			sizeof(struct usb_phy_generic_platform_data);
+		scnprintf(phy_id, MAX_STR, "usb_phy_generic.%d",
+					phy->port);
+		pdev = platform_device_register_full(&pdevinfo);
+		if (IS_ERR(pdev)) {
+			pr_err("%s: Failed to register device %s : %ld\n",
+				__func__,  phy_id, PTR_ERR(pdev));
+			kfree(phy_id);
 			continue;
 		}
 
 		usb_bind_phy("ehci-omap.0", phy->port - 1, phy_id);
 
-		/* Do we need RESET regulator ? */
-		if (gpio_is_valid(phy->reset_gpio)) {
-
-			rail_name = kmalloc(13, GFP_KERNEL);
-			if (!rail_name)
-				return -ENOMEM;
-
-			scnprintf(rail_name, 13, "hsusb%d_reset", phy->port);
-
-			usbhs_add_regulator(rail_name, phy_id, "reset",
-						phy->reset_gpio, 1);
-		}
-
 		/* Do we need VCC regulator ? */
 		if (gpio_is_valid(phy->vcc_gpio)) {
-
-			rail_name = kmalloc(13, GFP_KERNEL);
-			if (!rail_name)
-				return -ENOMEM;
-
-			scnprintf(rail_name, 13, "hsusb%d_vcc", phy->port);
-
+			scnprintf(rail_name, MAX_STR, "hsusb%d_vcc", phy->port);
 			usbhs_add_regulator(rail_name, phy_id, "vcc",
 					phy->vcc_gpio, phy->vcc_polarity);
 		}