--- zzzz-none-000/linux-3.10.107/arch/arm/mach-s3c24xx/s3c2412.c	2017-06-27 09:49:32.000000000 +0000
+++ scorpion-7490-727/linux-3.10.107/arch/arm/mach-s3c24xx/s3c2412.c	2021-02-04 17:41:59.000000000 +0000
@@ -20,8 +20,10 @@
 #include <linux/device.h>
 #include <linux/syscore_ops.h>
 #include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
+#include <linux/reboot.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
@@ -35,23 +37,17 @@
 #include <mach/regs-clock.h>
 #include <mach/regs-gpio.h>
 
-#include <plat/clock.h>
 #include <plat/cpu.h>
 #include <plat/cpu-freq.h>
 #include <plat/devs.h>
-#include <plat/nand-core.h>
-#include <plat/pll.h>
 #include <plat/pm.h>
-#include <plat/regs-serial.h>
 #include <plat/regs-spi.h>
 
 #include "common.h"
+#include "nand-core.h"
 #include "regs-dsc.h"
 #include "s3c2412-power.h"
 
-#define S3C2412_SWRST			(S3C24XX_VA_CLKPWR + 0x30)
-#define S3C2412_SWRST_RESET		(0x533C2412)
-
 #ifndef CONFIG_CPU_S3C2412_ONLY
 void __iomem *s3c24xx_va_gpio2 = S3C24XX_VA_GPIO;
 
@@ -129,26 +125,6 @@
 	cpu_do_idle();
 }
 
-void s3c2412_restart(char mode, const char *cmd)
-{
-	if (mode == 's')
-		soft_restart(0);
-
-	/* errata "Watch-dog/Software Reset Problem" specifies that
-	 * this reset must be done with the SYSCLK sourced from
-	 * EXTCLK instead of FOUT to avoid a glitch in the reset
-	 * mechanism.
-	 *
-	 * See the watchdog section of the S3C2412 manual for more
-	 * information on this fix.
-	 */
-
-	__raw_writel(0x00, S3C2412_CLKSRC);
-	__raw_writel(S3C2412_SWRST_RESET, S3C2412_SWRST);
-
-	mdelay(1);
-}
-
 /* s3c2412_map_io
  *
  * register the standard cpu IO areas, and any passed in from the
@@ -170,53 +146,6 @@
 	iotable_init(s3c2412_iodesc, ARRAY_SIZE(s3c2412_iodesc));
 }
 
-void __init_or_cpufreq s3c2412_setup_clocks(void)
-{
-	struct clk *xtal_clk;
-	unsigned long tmp;
-	unsigned long xtal;
-	unsigned long fclk;
-	unsigned long hclk;
-	unsigned long pclk;
-
-	xtal_clk = clk_get(NULL, "xtal");
-	xtal = clk_get_rate(xtal_clk);
-	clk_put(xtal_clk);
-
-	/* now we've got our machine bits initialised, work out what
-	 * clocks we've got */
-
-	fclk = s3c24xx_get_pll(__raw_readl(S3C2410_MPLLCON), xtal * 2);
-
-	clk_mpll.rate = fclk;
-
-	tmp = __raw_readl(S3C2410_CLKDIVN);
-
-	/* work out clock scalings */
-
-	hclk = fclk / ((tmp & S3C2412_CLKDIVN_HDIVN_MASK) + 1);
-	hclk /= ((tmp & S3C2412_CLKDIVN_ARMDIVN) ? 2 : 1);
-	pclk = hclk / ((tmp & S3C2412_CLKDIVN_PDIVN) ? 2 : 1);
-
-	/* print brieft summary of clocks, etc */
-
-	printk("S3C2412: core %ld.%03ld MHz, memory %ld.%03ld MHz, peripheral %ld.%03ld MHz\n",
-	       print_mhz(fclk), print_mhz(hclk), print_mhz(pclk));
-
-	s3c24xx_setup_clocks(fclk, hclk, pclk);
-}
-
-void __init s3c2412_init_clocks(int xtal)
-{
-	/* initialise the clocks here, to allow other things like the
-	 * console to use them
-	 */
-
-	s3c24xx_register_baseclocks(xtal);
-	s3c2412_setup_clocks();
-	s3c2412_baseclk_add();
-}
-
 /* need to register the subsystem before we actually register the device, and
  * we also need to ensure that it has been initialised before any of the
  * drivers even try to use it (even if not on an s3c2412 based system)
@@ -243,7 +172,7 @@
 {
 	printk("S3C2412: Initialising architecture\n");
 
-#ifdef CONFIG_PM
+#ifdef CONFIG_PM_SLEEP
 	register_syscore_ops(&s3c2412_pm_syscore_ops);
 	register_syscore_ops(&s3c24xx_irq_syscore_ops);
 #endif